EN IEC 61169-65:2021

SLOVENSKI STANDARD
01-maj-2021
Radiofrekvenčni konektorji - 65. del: Področna specifikacija za radiofrekvenčne
(RF) koaksialne konektorje z notranjim premerom 1,35 mm zunanjega prevodnika,
z vijačno spojko in značilno impedanco 50 ohm (IEC 61169-65:2021)
Radio-frequency connectors - Part 65: Sectional specification for RF coaxial connectors,
1,35 mm inner diameter of outer conductor, with screw-coupling, characteristic
impedance 50 Ohm (IEC 61169-65:2021)
Hochfrequenz-Steckverbinder – Teil 65: Rahmenspezifikation für koaxiale HF-
Steckverbinder mit 1,35 mm Innendurchmesser des Außenleiters, mit Schraubkupplung,
Wellenwiderstand 50 Ohm, für den Einsatz bis 90 GHz (IEC 61169-65:2021)
Connecteurs pour fréquences radioélectriques - Partie 65: Spécification intermédiaire
relative aux connecteurs coaxiaux pour fréquences radioélectriques, avec un diamètre
intérieur du conducteur extérieur de 1,35 mm, à couplage à vis, impédance
caractéristique de 50 Ω (IEC 61169-65:2021)
Ta slovenski standard je istoveten z: EN IEC 61169-65:2021
ICS:
33.120.30 Radiofrekvenčni konektorji RF connectors
(RF)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EUROPEAN STANDARD EN IEC 61169-65

NORME EUROPÉENNE
EUROPÄISCHE NORM
February 2021
ICS 33.120.30
English Version
Radio-frequency connectors - Part 65: Sectional specification for
RF coaxial connectors, 1,35 mm inner diameter of outer
conductor, with screw-coupling, characteristic impedance 50 O
(IEC 61169-65:2021)
Connecteurs pour fréquences radioélectriques - Partie 65: Hochfrequenz-Steckverbinder - Teil 65:
Spécification intermédiaire relative aux connecteurs Rahmenspezifikation für koaxiale HF-Steckverbinder mit
coaxiaux pour fréquences radioélectriques, avec un 1,35 mm Innendurchmesser des Außenleiters, mit
diamètre intérieur du conducteur extérieur de 1,35 mm, à Schraubkupplung, Wellenwiderstand 50 Ohm, für den
couplage à vis, impédance caractéristique de 50 O Einsatz bis 90 GHz
(IEC 61169-65:2021) (IEC 61169-65:2021)
This European Standard was approved by CENELEC on 2021-02-23. CENELEC members are bound to comply with the CEN/CENELEC
Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC
Management Centre or to any CENELEC member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CENELEC member into its own language and notified to the CEN-CENELEC Management Centre has the
same status as the official versions.
CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic,
Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the
Netherlands, Norway, Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and the United Kingdom.

European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2021 CENELEC All rights of exploitation in any form and by any means reserved worldwide for CENELEC Members.
Ref. No. EN IEC 61169-65:2021 E

European foreword
The text of document 46F/527(F)/FDIS, future edition 1 of IEC 61169-65, prepared by SC 46F “RF
and microwave passive components” of IEC/TC 46 “Cables, wires, waveguides, RF connectors, RF
and microwave passive components and accessories” was submitted to the IEC-CENELEC parallel
vote and approved by CENELEC as EN IEC 61169-65:2021.
The following dates are fixed:
• latest date by which the document has to be implemented at national (dop) 2021–11–23
level by publication of an identical national standard or by endorsement
• latest date by which the national standards conflicting with the (dow) 2024–02–23
document have to be withdrawn
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CENELEC shall not be held responsible for identifying any or all such patent rights.
Endorsement notice
The text of the International Standard IEC 61169-65:2021 was approved by CENELEC as a European
Standard without any modification.
Annex ZA
(normative)
Normative references to international publications
with their corresponding European publications
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments)
applies.
NOTE 1 Where an International Publication has been modified by common modifications, indicated by (mod), the
relevant EN/HD applies.
NOTE 2 Up-to-date information on the latest versions of the European Standards listed in this annex is available
here: www.cenelec.eu.
Publication Year Title EN/HD Year
IEC 61169-1 2013 Radio frequency connectors - Part 1:EN 61169-1 2013
Generic specification - General
requirements and measuring methods
IEC 61726 - Cable assemblies, cables, connectors andEN 61726 -
passive microwave components -
Screening attenuation measurement by
the reverberation chamber method
IEC 62037 - RF connectors, connector cable- -
assemblies and cables - Intermodulation
level measurement
IEC 62153-4-7 - Metallic communication cable testEN 62153-4-7 -
methods - Part 4–7: Electromagnetic
compatibility (EMC) - Test method for
measuring of transfer impedance Z and
T
screening attenuation as or coupling
attenuation a of connectors and
c
assemblies up to and above 3 GHz -
Triaxial tube in tube method
IEC 61169-65 ®
Edition 1.0 2021-01
INTERNATIONAL
STANDARD
NORME
INTERNATIONALE
Radio-frequency connectors –
Part 65: Sectional specification for RF coaxial connectors, 1,35 mm inner

diameter of outer conductor, with screw-coupling, characteristic

impedance 50 Ω
Connecteurs pour fréquences radioélectriques –

Partie 65: Spécification intermédiaire relative aux connecteurs coaxiaux pour

fréquences radioélectriques, avec un diamètre intérieur du conducteur extérieur

de 1,35 mm, à couplage à vis, impédance caractéristique de 50 Ω

INTERNATIONAL
ELECTROTECHNICAL
COMMISSION
COMMISSION
ELECTROTECHNIQUE
INTERNATIONALE
ICS 33.120.30 ISBN 978-2-8322-9259-4

– 2 – IEC 61169-65:2021 © IEC 2021
CONTENTS
FOREWORD . 3
1 Scope . 5
2 Normative references . 5
3 Terms and definitions . 5
4 Mating face and gauge information . 6
4.1 Dimensions – General purpose connectors – Grade 1 . 6
4.1.1 Connector with pin centre contact . 6
4.1.2 General purpose connector with socket centre contact . 7
4.2 Gauge pin for socket centre contact . 8
4.2.1 Dimensions . 8
4.2.2 Test procedure . 8
4.3 Dimensions standard test connectors – Grade 0 . 8
4.3.1 Standard test connector with pin centre contact . 8
4.3.2 Standard test connector with socket centre contact . 9
5 Quality assessment procedures . 11
5.1 General . 11
5.2 Ratings and characteristics (see Clause 5 of IEC 61169-1:2013) . 11
5.3 Test schedule and inspection requirements. 12
5.3.1 Acceptance tests . 12
5.3.2 Periodic tests . 13
5.4 Procedures for quality conformance . 15
5.4.1 Quality conformance inspection . 15
5.4.2 Quality conformance and its maintenance . 15
6 Instructions for preparation of detail specifications . 15
6.1 General . 15
6.2 Identification of the component . 15
6.3 Performance . 15
6.4 Marking, ordering information and related matters . 16
6.5 Selection of tests, test conditions and severities . 16
6.6 Blank detail specification pro-forma for 1,35 mm connectors . 16

Figure 1 – General purpose connector with pin centre contact . 6
Figure 2 – General purpose connector with socket centre contact . 7
Figure 3 – Gauge pin for socket centre contact . 8
Figure 4 – Standard test connector with pin centre contact . 9
Figure 5 – Standard test connector with socket centre contact . 10

Table 1 – Dimensions of connector with pin centre contact – Grade 1 . 6
Table 2 – Dimensions of connector with socket centre contact – Grade 1 . 7
Table 3 – Dimensions of gauge pin for socket centre contact . 8
Table 4 – Dimensions of connector with pin centre contact – Grade 0 . 9
Table 5 – Dimensions of connector with socket centre contact – Grade 0 . 10
Table 6 – Ratings and characteristics . 11
Table 7 – Acceptance tests . 12
Table 8 – Periodic tests . 13

IEC 61169-65:2021 © IEC 2021 – 3 –
INTERNATIONAL ELECTROTECHNICAL COMMISSION
____________
RADIO-FREQUENCY CONNECTORS –
Part 65: Sectional specification for RF coaxial connectors,
1,35 mm inner diameter of outer conductor, with screw-coupling,
characteristic impedance 50 Ω
FOREWORD
1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of IEC is to promote
international co-operation on all questions concerning standardization in the electrical and electronic fields. To
this end and in addition to other activities, IEC publishes International Standards, Technical Specifications,
Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC
Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested
in the subject dealt with may participate in this preparatory work. International, governmental and non-
governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely
with the International Organization for Standardization (ISO) in accordance with conditions determined by
agreement between the two organizations.
2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international
consensus of opinion on the relevant subjects since each technical committee has representation from all
interested IEC National Committees.
3) IEC Publications have the form of recommendations for international use and are accepted by IEC National
Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC
Publications is accurate, IEC cannot be held responsible for the way in w
...