EN IEC 63295:2022

SLOVENSKI STANDARD
01-junij-2022
Specifikacija za steklene perlice serije WB z impedanco 50Ω za konektorje RF (IEC
63295:2022)
Specification for WB series glass beads with 50Ω impedance for RF connectors (IEC
63295:2022)
Spezifikation für Glasperlen der Serie WB mit 50Ω Impedanz für HF-Steckverbinder (IEC
63295:2022)
Spécification pour perles en verre de série WB à impédance de 50 Ω pour connecteurs
RF (IEC 63295:2022)
Ta slovenski standard je istoveten z: EN IEC 63295:2022
ICS:
33.120.30 Radiofrekvenčni konektorji RF connectors
(RF)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EUROPEAN STANDARD EN IEC 63295

NORME EUROPÉENNE
EUROPÄISCHE NORM April 2022
ICS 33.120.30
English Version
Specification for WB series glass beads with 50 O impedance for
RF connectors
(IEC 63295:2022)
Spécification pour perles en verre de série WB à Spezifikation für Glasperlen der Serie WB mit 50O
impédance de 50 O pour connecteurs RF Impedanz für HF-Steckverbinder
(IEC 63295:2022) (IEC 63295:2022)
This European Standard was approved by CENELEC on 2022-03-31. CENELEC members are bound to comply with the CEN/CENELEC
Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC
Management Centre or to any CENELEC member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CENELEC member into its own language and notified to the CEN-CENELEC Management Centre has the
same status as the official versions.
CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic,
Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the
Netherlands, Norway, Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and the United Kingdom.

European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2022 CENELEC All rights of exploitation in any form and by any means reserved worldwide for CENELEC Members.
Ref. No. EN IEC 63295:2022 E
European foreword
The text of document 46F/597/FDIS, future edition 1 of IEC 63295, prepared by SC 46F "RF and
microwave passive components" of IEC/TC 46 "Cables, wires, waveguides, RF connectors, RF and
microwave passive components and accessories" was submitted to the IEC-CENELEC parallel vote
and approved by CENELEC as EN IEC 63295:2022.
The following dates are fixed:
• latest date by which the document has to be implemented at national (dop) 2022-12-31
level by publication of an identical national standard or by endorsement
• latest date by which the national standards conflicting with the (dow) 2025-03-31
document have to be withdrawn
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CENELEC shall not be held responsible for identifying any or all such patent rights.
Any feedback and questions on this document should be directed to the users’ national committee. A
complete listing of these bodies can be found on the CENELEC website.
Endorsement notice
The text of the International Standard IEC 63295:2022 was approved by CENELEC as a European
Standard without any modification.
Annex ZA
(normative)
Normative references to international publications
with their corresponding European publications
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments)
applies.
NOTE 1  Where an International Publication has been modified by common modifications, indicated by (mod),
the relevant EN/HD applies.
NOTE 2  Up-to-date information on the latest versions of the European Standards listed in this annex is available
here: www.cenelec.eu.
Publication Year Title EN/HD Year
IEC 61169-1 2013 Radio frequency connectors - Part 1: Generic EN 61169-1 2013
specification - General requirements and
measuring methods
IEC 62153-4-7 - Metallic cables and other passive components EN IEC 62153-4-7 -
test methods - Part 4-7: Electromagnetic
compatibility (EMC) - Test method for
measuring of transfer impedance Z and
T
screening attenuation a or coupling
S
attenuation a of connectors and assemblies -
C
Triaxial tube in tube method
IEC 63295 ®
Edition 1.0 2022-02
INTERNATIONAL
STANDARD
NORME
INTERNATIONALE
Specification for WB series glass beads with 50 Ω impedance for RF connectors

Spécification pour perles en verre de série WB à impédance de 50 Ω pour

connecteurs RF
INTERNATIONAL
ELECTROTECHNICAL
COMMISSION
COMMISSION
ELECTROTECHNIQUE
INTERNATIONALE
ICS 33.120.30 ISBN 978-2-8322-1081-8

– 2 – IEC 63295:2022 © IEC 2022
CONTENTS
FOREWORD . 3
1 Scope . 5
2 Normative references . 5
3 Terms and definitions . 5
4 Structure dimensions and IEC type designation . 5
5 Quality assessment procedure . 6
5.1 General . 6
5.2 Ratings and characteristics . 6
5.3 Test schedule and inspection requirements. 9
5.3.1 Acceptance tests . 9
5.3.2 Periodic tests . 10
5.4 Procedures for quality conformance . 12
5.4.1 Quality conformance inspection . 12
5.4.2 Quality conformance and its maintenance . 12
6 Marking . 12
6.1 Marking of components . 12
6.2 Marking and contents of package . 13
Annex A (Informative) Type designation . 14
Annex B (Informative) Typical applications . 15
Annex C (Informative) Test fixture . 16
C.1 Test fixture. 16
C.2 Dimensions for test fixture . 16

Figure 1 – Structure of WB series glass beads . 6
Figure B.1 – WB series glass bead used in PCB to connect with RF connector . 15
Figure B.2 – WB series glass bead used in PCB as an inner conductor of an RF
connector . 15
Figure C.1 – Test fixture . 16
Figure C.2 – Test fixture . 17

Table 1 – Dimensions of WB series glass beads . 6
Table 2 – Ratings and characteristics . 7
Table 3 – Acceptance tests . 10
Table 4 – Periodic tests . 11
Table C.1 – Test fixtures per type of glass-bead . 16
Table C.2 – Dimensions of test fixtures . 17

IEC 63295:2022 © IEC 2022 – 3 –
INTERNATIONAL ELECTROTECHNICAL COMMISSION
____________
SPECIFICATION FOR WB SERIES GLASS BEADS
WITH 50 Ω IMPEDANCE FOR RF CONNECTORS

FOREWORD
1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of IEC is to promote international
co-operation on all questions concerning standardization in the electrical and electronic fields. To this end and
in addition to other activities, IEC publishes International Standards, Technical Specifications, Technical Reports,
Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC Publication(s)”). Their
preparation is entrusted to technical committees; any IEC National Committee interested in the subject dealt with
may participate in this preparatory work. International, governmental and non-governmental organizations liaising
with the IEC also participate in this preparation. IEC collaborates closely with the International Organization for
Standardization (ISO) in accordance with conditions determined by agreement between the two organizations.
2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international
consensus of opinion on the relevant subjects since each technical committee has representation from all
interested IEC National Committees.
3) IEC Publications have the form of recommendations for international use and are accepted by IEC National
Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC
Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any
misinterpretation by any end user.
4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications
transparently to the maximum extent possible in their national and regional publications. Any divergence between
any IEC Publication and the corresponding national or regional publication shall be clearly indicated in the latter.
5) IEC itself does not provide any attestation of conformity. Independent certification bodies provide conformity
assessment services and, in some areas, access to IEC marks of conformity. IEC is not responsible for any
services carried out by independent certification bodies.
6) All users should ensure that they have the latest edition of this publication.
7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and
members of its technical committees and IEC National Committees for any personal injury, property damage or
other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and
expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC
Publications.
8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is
indispensable for the correct application of this publication.
9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of patent
rights. IEC shall not be held responsible for identifying any or all such patent rights.
IEC 63295 has been prepared by subcommittee 46F: RF and microwave passive components,
of IEC technical committee 46: Cables, wires, waveguides, RF connectors, RF and microwave
passive components and accessories. It is an International Standard.
The text of this International Standard is based on the following documents:
Draft Report on voting
46F/597/FDIS 46F/611/RVD
Full information on the voting for its approval can be found in the report on voting indicated in
the above table.
The language used for the development of this International Standard is English.
This document was drafted in accordance with ISO/IEC Directives, Part 2, and developed in
accordance with ISO/IEC Directives, Part 1 and ISO/IEC Directives, IEC Supplement, available
at www.iec.ch/mem
...