Specifications for particular types of winding wires - Part 27: Paper tape covered rectangular copper wire

IEC 60317-27:2013 specifies the requirements of paper tape covered rectangular copper winding wires. This covering consists of two or more layers of paper tape, all in the same direction and is primarily intended for winding coils for oil immersed transformers. The range of nominal conductor dimensions covered by this standard is: - width: min. 2,0 mm max. 16,0 mm; - thickness: min. 0,80 mm max. 5,60 mm. The paper tapes covered by this standard are restricted to those specified in IEC 60554-1 having thicknesses in the range 25 μm to 125 μm inclusive. This fourth edition cancels and replaces the third edition published in 1998, Amendment 1:1999. This edition constitutes a technical revision. This edition includes the following significant technical changes with respect to the previous edition: - new subclause containing general notes on winding wire, formerly a part of the scope; - revision to references to IEC 60317-0-2:2013 to clarify that their application is normative; - new 3.3, Appearance; - modification to 4.4, Increase in dimensions due to paper tape covering; - deletion of Clause 22, High temperature failure; - new Clause 23, Pin hole test. Keywords: requirements of paper tape covered rectangular copper winding wires, winding coils for oil immersed transformers

Technische Lieferbedingungen für bestimmte Typen von Wickeldrähten - Teil 27: Flachdrähte aus Kupfer, papierisoliert

Spécifications pour types particuliers de fils de bobinage - Partie 27: Fil de section rectangulaire en cuivre recouvert de ruban papier

La CEI 60317-27:2013 spécifie les exigences relatives au fil de bobinage de section rectangulaire en cuivre recouvert de ruban papier. Ce revêtement est constitué de deux ou plusieurs couches de ruban papier, enroulées toutes dans le même sens, et est essentiellement destiné au bobinage pour les transformateurs immergés dans l'huile. La gamme des dimensions nominales des conducteurs couvertes par la présente norme est: - la largeur: min. 2,0 mm max. 16,0 mm; - l'épaisseur: min. 0,80 mm max. 5,60 mm. Les rubans papier concernés par cette norme sont limités à ceux qui possèdent une épaisseur de 25 μm à 125 μm compris et qui sont spécifiés dans la CEI 60554-1. Cette quatrième édition annule et remplace la troisième édition parue en 1998, et l'Amendement 1:1999. Cette édition constitue une révision technique. Cette édition inclut les modifications techniques majeures suivantes par rapport à l'édition précédente: - un nouveau paragraphe contenant des notes générales sur le fil de bobinage intégrées auparavant au domaine d'application; - la révision des références à la CEI 60317-0-2:2013, pour bien établir que leur application est normative; - un nouveau 3.3, Aspect; - une révision du 4.4, Accroissement des dimensions dû au revêtement de ruban papier; - la suppression de l'Article 22 Défaillance à haute température; - un nouvel Article 23, Détection des microfissures en immersion. Mots clés: exigences relatives au fil de bobinage de section rectangulaire en cuivre recouvert de ruban papier, bobinage pour les transformateurs immergés dans l'huile

Specifikacije za posebne vrste navijalnih žic - 27. del: S papirnim trakom ovita pravokotna bakrena žica (IEC 60317-27:2013)

General Information

Status
Withdrawn
Publication Date
13-Feb-2014
Withdrawal Date
13-Nov-2016
Technical Committee
Drafting Committee
Current Stage
9960 - Withdrawal effective - Withdrawal
Start Date
18-Dec-2022
Completion Date
18-Dec-2022

Relations

Buy Standard

Standard
EN 60317-27:2014
English language
15 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)


2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Specifikacije za posebne vrste navijalnih žic - 27. del: S papirnim trakom ovita pravokotna bakrena žica (IEC 60317-27:2013)/Spécifications pour types particuliers de fils de bobinage - Partie 27: Fil de section rectangulaire en cuivre recouvert de ruban papierSpecifications for particular types of winding wires - Part 27: Paper tape covered rectangular copper wire29.060.10ŽiceWiresICS:Ta slovenski standard je istoveten z:EN 60317-27:2014SIST EN 60317-27:2014en01-april-2014SIST EN 60317-27:2014SLOVENSKI
STANDARDSIST EN 60317-27:2001/A1:2001SIST EN 60317-27:20011DGRPHãþD

EUROPEAN STANDARD EN 60317-27 NORME EUROPÉENNE
EUROPÄISCHE NORM February 2014
CENELEC European Committee for Electrotechnical Standardization Comité Européen de Normalisation Electrotechnique Europäisches Komitee für Elektrotechnische Normung
CEN-CENELEC Management Centre: Avenue Marnix 17, B - 1000 Brussels
© 2014 CENELEC -
All rights of exploitation in any form and by any means reserved worldwide for CENELEC members.
Ref. No. EN 60317-27:2014 E
ICS 29.060.10 Supersedes EN 60317-27:1998 + A1:2000
English version
Specifications for particular types of winding wires -
Part 27: Paper tape covered rectangular copper wire (IEC 60317-27:2013)
Spécifications pour types particuliers de fils de bobinage -
Partie 27: Fil de section rectangulaire en cuivre recouvert de ruban papier (CEI 60317-27:2013)
Technische Lieferbedingungen für bestimmte Typen von Wickeldrähten -
Teil 27: Flachdrähte aus Kupfer, papierisoliert (IEC 60317-27:2013)
This European Standard was approved by CENELEC on 2013-11-14. CENELEC members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CENELEC member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CENELEC member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions.
CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom.
The following dates are fixed: • latest date by which the document has to be implemented at national level by publication of an identical national standard or by endorsement (dop) 2014-08-14 • latest date by which the national standards conflicting with the document have to be withdrawn (dow) 2016-11-14
This document supersedes EN 60317-27:1998.
This standard is to be read in conjunction with EN 60317-0-2:2014.
The numbering of clauses in this standard is not continuous from Clauses 20 and 30 in order to reserve space for possible future wire requirements prior to those for wire packaging.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CENELEC [and/or CEN] shall not be held responsible for identifying any or all such patent rights.
Endorsement notice The text of the International Standard IEC 60317-27:2013 was approved by CENELEC as a European Standard without any modification. In the official version, for Bibliography, the following notes have to be added for the standards indicated:
IEC 60264 Series NOTE Harmonized as EN 60264 Series (not modified). IEC 60317 Series NOTE Harmonized as EN 60317 Series (not modified). IEC 60851 Series NOTE Harmonized as EN 60851 Series (not modified). ISO 6892-1:2009 NOTE Harmonized as EN ISO 6892-1:2009 (not modified). SIST EN 60317-27:2014

- 3 - EN 60317-27:2014 Annex ZA
(normative)
Normative references to international publications with their corresponding European publications
The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies.
NOTE
When an international publication has been modified by common modifications, indicated by (mod), the relevant EN/HD applies.
Publication Year Title EN/HD Year
IEC 60317-0-2 2013 Specifications for particular types
of winding wires -
Part 0-2: General requirements -
Enamelled rectangular copper wire EN 60317-0-2 2014
IEC 60554-1 - Specification for cellulosic papers for electrical purposes -
Part 1: Definitions and general requirements - -
IEC 60317-27 Edition 4.0 2013-10 INTERNATIONAL STANDARD NORME INTERNATIONALE Specifications for particular types of winding wires – Part 27: Paper tape covered rectangular copper wire
Spécifications pour types particuliers de fils de bobinage – Partie 27: Fil de section rectangulaire en cuivre recouvert de ruban papier
INTERNATIONAL ELECTROTECHNICAL COMMISSION COMMISSION ELECTROTECHNIQUE INTERNATIONALE M ICS 29.060.10 PRICE CODE CODE PRIX ISBN 978-2-8322-1154-0
– 2 – 60317-27 © IEC:2013 CONTENTS FOREWORD . 3 INTRODUCTION . 5 1 Scope . 6 2 Normative references . 6 3 Terms, definitions, general notes and appearance . 6 3.1 Terms and definitions . 6 3.2 General notes . 6 3.2.1 Methods of test . 6 3.2.2 Winding wire . 7 3.3 Appearance . 7 4 Dimensions . 7 4.1 Conductor dimensions . 7 4.2 Tolerance on conductor dimensions . 7 4.3 Rounding of corners . 7 4.4 Increase in dimensions due to paper tape covering . 7 4.5 Maximum overall dimensions . 8 5 Electrical resistance . 8 6 Elongation . 8 7 Springiness . 8 8 Flexibility and adherence . 8 9 Heat shock . 8 10 Cut-through . 8 11 Resistance to abrasion . 9 12 Resistance to solvents . 9 13 Breakdown voltage . 9 14 Continuity of insulation . 9 15 Temperature index . 9 16 Resistance to refrigerants . 9 17 Solderability . 9 18 Heat or solvent bonding . 9 19 Dielectric dissipation factor . 9 20 Resistance to hydrolysis and to transformer oil . 9 21 Loss of mass . 9 23 Pin hole test . 9 30 Packaging . 10 Annex A (informative)
Method of determination of x % proof stress: Rpx . 11 Bibliography . 12
Figure A.1 – Load-elongation diagram . 11
Table 1 – Increase in dimensions . 8
60317-27 © IEC:2013 – 3 – INTERNATIONAL ELECTROTECHNICAL COMMISSION ____________
SPECIFICATIONS FOR PARTICULAR
TYPES OF WINDING WIRES –
Part 27: Paper tape covered rectangular copper wire
FOREWORD 1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising all national electrotechnical committees (IEC National Committees). The object of IEC is to promote international co-operation on all questions concerning standardization in the electrical and electronic fields. To this end and in addition to other activities, IEC publishes International Standards, Technical Specifications, Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested in the subject dealt with may participate in this preparatory work. International, governmental and non-governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely with the International Organization for Standardization (ISO) in accordance with conditions determined by agreement between the two organizations. 2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international consensus of opinion on the relevant subjects since each technical committee has representation from all interested IEC National Committees.
3) IEC Publications have the form of recommendations for international use and are accepted by IEC National Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any misinterpretation by any end user. 4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications transparently to the maximum extent possible in their national and regional publications. Any divergence between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in the latter. 5) IEC itself does not provide any attestation of conformity. Independent certification bodies provide conformity assessment services and, in some areas, access to IEC marks of conformity. IEC is not responsible for any services carried out by independent certification bodies. 6) All users should ensure that they have the latest edition of this publication. 7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and members of its technical committees and IEC National Committees for any personal injury, property damage or other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC Publications.
8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is indispensable for the correct application of this publication. 9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of patent rights. IEC shall not be held resp
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.