EN IEC 61300-2-14:2021

SLOVENSKI STANDARD
01-junij-2021
Nadomešča:
SIST EN 61300-2-14:2013
Optični spojni elementi in pasivne komponente - Osnovni preskusni in merilni
postopki - 2-14. del: Preskusi - Visoka optična moč (IEC 61300-2-14:2021)
Fibre optic interconnecting devices and passive components - Basic test and
measurement procedures - Part 2-14: Tests - High optical power (IEC 61300-2-14:2021)
Lichtwellenleiter - Verbindungselemente und passive Bauteile - Grundlegende Prüf- und
Messverfahren - Teil 2-14: Prüfungen - Hohe Optische Leistung (IEC 61300-2-14:2021)
Dispositifs d'interconnexion et composants passifs à fibres optiques - Méthodes
fondamentales d'essais et de mesures - Partie 2-14: Essais - Puissance optique élevée
(IEC 61300-2-14:2021)
Ta slovenski standard je istoveten z: EN IEC 61300-2-14:2021
ICS:
33.180.20 Povezovalne naprave za Fibre optic interconnecting
optična vlakna devices
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EUROPEAN STANDARD EN IEC 61300-2-14

NORME EUROPÉENNE
EUROPÄISCHE NORM
March 2021
ICS 33.180.20 Supersedes EN 61300-2-14:2013 and all of its
amendments and corrigenda (if any)
English Version
Fibre optic interconnecting devices and passive components -
Basic test and measurement procedures - Part 2-14: Tests -
High optical power
(IEC 61300-2-14:2021)
Dispositifs d'interconnexion et composants passifs Lichtwellenleiter - Verbindungselemente und passive
fibroniques - Procédures fondamentales d'essais et de Bauteile - Grundlegende Prüf- und Messverfahren - Teil 2-
mesures - Partie 2-14: Essais - Puissance optique élevée 14: Prüfungen - Hohe Optische Leistung
(IEC 61300-2-14:2021) (IEC 61300-2-14:2021)
This European Standard was approved by CENELEC on 2021-03-18. CENELEC members are bound to comply with the CEN/CENELEC
Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC
Management Centre or to any CENELEC member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CENELEC member into its own language and notified to the CEN-CENELEC Management Centre has the
same status as the official versions.
CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic,
Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the
Netherlands, Norway, Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and the United Kingdom.

European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2021 CENELEC All rights of exploitation in any form and by any means reserved worldwide for CENELEC Members.
Ref. No. EN IEC 61300-2-14:2021 E

European foreword
The text of document 86B/4299/CDV, future edition 4 of IEC 61300-2-14, prepared by SC 86B "Fibre
optic interconnecting devices and passive components" of IEC/TC 86 "Fibre optics" was submitted to
the IEC-CENELEC parallel vote and approved by CENELEC as EN IEC 61300-2-14:2021.
The following dates are fixed:
• latest date by which the document has to be implemented at national (dop) 2021-12-18
level by publication of an identical national standard or by endorsement
• latest date by which the national standards conflicting with the (dow) 2024-03-18
document have to be withdrawn
This document supersedes EN 61300-2-14:2013 and all of its amendments and corrigenda (if any).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CENELEC shall not be held responsible for identifying any or all such patent rights.
Endorsement notice
The text of the International Standard IEC 61300-2-14:2021 was approved by CENELEC as a
European Standard without any modification.
In the official version, for Bibliography, the following notes have to be added for the standards
indicated:
IEC 61300 (series) NOTE Harmonized as EN 61300 (series)
IEC 61300-3-4:2012 NOTE Harmonized as EN 61300-3-4:2013 (not modified)
IEC 62005-9-4 NOTE Harmonized as EN IEC 62005-9-4
Annex ZA
(normative)
Normative references to international publications
with their corresponding European publications
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments)
applies.
NOTE 1  Where an International Publication has been modified by common modifications, indicated by (mod),
the relevant EN/HD applies.
NOTE 2  Up-to-date information on the latest versions of the European Standards listed in this annex is available
here: www.cenelec.eu.
Publication Year Title EN/HD Year
IEC 60825-1 - Safety of laser products - Part 1: EN 60825-1 -
Equipment classification and requirements
IEC 61300-1 - Fibre optic interconnecting devices and EN IEC 61300-1 -
passive components - Basic test and
measurement procedures - Part 1: General
and guidance
IEC 61300-3-1 - Fibre optic interconnecting devices and EN 61300-3-1 -
passive components - Basic test and
measurement procedures - Part 3-1:
Examinations and measurements - Visual
examination
IEC 61300-3-3 - Fibre optic interconnecting devices and EN 61300-3-3 -
passive components - Basic test and
measurement procedures - Part 3-3:
Examinations and measurements - Active
monitoring of changes in attenuation and
return loss
IEC 61300-3-35 - Fibre optic interconnecting devices and EN IEC 61300-3-35 -
passive components - Basic test and
measurement procedures - Part 3-35:
Examinations and measurements - Visual
inspection of fibre optic connectors and
fibre-stub transceivers
IEC 61300-2-14 ®
Edition 4.0 2021-02
INTERNATIONAL
STANDARD
NORME
INTERNATIONALE
Fibre optic interconnecting devices and passive components – Basic test and

measurement procedures –
Part 2-14: Tests – High optical power

Dispositifs d'interconnexion et composants passifs fibroniques – Procédures

fondamentales d'essais et de mesures –

Partie 2-14: Essais – Puissance optique élevée

INTERNATIONAL
ELECTROTECHNICAL
COMMISSION
COMMISSION
ELECTROTECHNIQUE
INTERNATIONALE
ICS 33.180.20 ISBN 978-2-8322-9267-9

– 2 – IEC 61300-2-14:2021 © IEC 2021
CONTENTS
FOREWORD . 3
1 Scope . 5
2 Normative references . 5
3 Terms, definitions and abbreviated terms . 5
3.1 Terms and definitions . 5
3.2 Abbreviated terms . 5
4 Apparatus . 6
4.1 Source (S) . 6
4.2 Optical detector (D) . 6
4.3 Environmental chamber . 7
4.4 Data acquisition system (DAS) . 7
4.5 Branching device (BD) . 7
4.6 Temporary joints (TJ) . 7
4.7 Safety devices . 7
4.8 Test set-up . 7
5 Procedure . 8
5.1 Preconditioning . 8
5.2 Initial examinations and measurements . 8
5.3 Conditioning . 8
5.4 Recovery . 8
5.5 Final examinations and measurements . 9
6 Severity . 9
6.1 General . 9
6.2 Optical power . 9
6.3 Wavelengths . 9
6.4 Temperature . 9
6.5 Humidity . 9
6.6 Exposure time . 9
7 Details to be specified . 10
Annex A (normative) Examples of test set-up . 11
A.1 WDM devices . 11
A.2 Input optical power from both ends . 11
A.3 Series connection set-up . 12
Annex B (informative) Examples of pass/fail criteria during exposure time . 14
B.1 General . 14
B.2 Attenuation limitation of monitoring . 14
B.3 Return loss limitation . 15
B.4 Judgment based on the change . 15
Bibliography . 16

Figure 1 – Typical optical power test set-up . 7
Figure A.1 – Example of optical power test set-up for a 2 x 1 WDM device . 11
Figure A.2 – Example of test set-up of both direction input test . 12
Figure A.3 – Example of optical power test set-up in series connection . 13

IEC 61300-2-14:2021 © IEC 2021 – 3 –
INTERNATIONAL ELECTROTECHNICAL COMMISSION
____________
FIBRE OPTIC INTERCONNECTING DEVICES
AND PASSIVE COMPONENTS –
BASIC TEST AND MEASUREMENT PROCEDURES –

Part 2-14: Tests – High optical power

FOREWORD
1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of IEC is to promote international
co-operation on all questions concerning standardization in the electrical and electronic fields. To this end and
in addition to other activities, IEC publishes International Standards, Technical Specifications, Technical Reports,
Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC Publication(s)”). Their
preparation is entrusted to technical committees; any IEC National Committee interested in the subject dealt with
may participate in this preparatory work. International, governmental and non-governmental organizations liaising
with the IEC also participate in this preparation. IEC collaborates closely with the International Organization for
Standardization (ISO) in accordance with conditions determined by agreement between the two organizations.
2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international
consensus of opinio
...