EN IEC 60794-1-209:2024

SLOVENSKI STANDARD
01-september-2024
Optični kabli - 1-209. del: Splošna specifikacija - Osnovni preskusni postopki za
optične kable - Okoljske preskusne metode - Staranje, metoda F9 (IEC 60794-1-
209:2024)
Optical fibre cables - Part 1-209: Generic specification - Basic optical cable test
procedures - Environmental test methods - Ageing, Method F9 (IEC 60794-1-209:2024)
Lichtwellenleiterkabel - Teil 1-209: Fachgrundspezifikation - Grundlegende Prüfverfahren
für optische Kabel - Umweltprüfverfahren - Alterung, Verfahren F9 (IEC 60794-1-
209:2024)
Câbles à fibres optiques - Partie 1-209: Spécification générique - Procédures
fondamentales d’essai des câbles optiques - Méthodes d’essai d’environnement -
Vieillissement, méthode f9 (IEC 60794-1-209:2024)
Ta slovenski standard je istoveten z: EN IEC 60794-1-209:2024
ICS:
33.180.10 (Optična) vlakna in kabli Fibres and cables
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EUROPEAN STANDARD EN IEC 60794-1-209

NORME EUROPÉENNE
EUROPÄISCHE NORM July 2024
ICS 33.180.10 Supersedes EN IEC 60794-1-22:2018 (partially)
English Version
Optical fibre cables - Part 1-209: Generic specification - Basic
optical cable test procedures - Environmental test methods -
Ageing, method F9
(IEC 60794-1-209:2024)
Câbles à fibres optiques - Partie 1-209: Spécification Lichtwellenleiterkabel - Teil 1-209: Fachgrundspezifikation -
générique - Procédures fondamentales d'essai des câbles Grundlegende Prüfverfahren für optische Kabel -
optiques - Méthodes d'essai d'environnement - Umweltprüfverfahren - Alterung, Verfahren F9
Vieillissement, méthode F9 (IEC 60794-1-209:2024)
(IEC 60794-1-209:2024)
This European Standard was approved by CENELEC on 2024-07-04. CENELEC members are bound to comply with the CEN/CENELEC
Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC
Management Centre or to any CENELEC member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CENELEC member into its own language and notified to the CEN-CENELEC Management Centre has the
same status as the official versions.
CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic,
Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the
Netherlands, Norway, Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Türkiye and the United Kingdom.

European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2024 CENELEC All rights of exploitation in any form and by any means reserved worldwide for CENELEC Members.
Ref. No. EN IEC 60794-1-209:2024 E

European foreword
The text of document 86A/2443/FDIS, future edition 1 of IEC 60794-1-209, prepared by SC 86A
"Fibres and cables" of IEC/TC 86 "Fibre optics" was submitted to the IEC-CENELEC parallel vote and
approved by CENELEC as EN IEC 60794-1-209:2024.
The following dates are fixed:
• latest date by which the document has to be implemented at national (dop) 2025-04-04
level by publication of an identical national standard or by endorsement
• latest date by which the national standards conflicting with the (dow) 2027-07-04
document have to be withdrawn
This document partially supersedes EN IEC 60794-1-22:2018 and all of its amendments and
corrigenda (if any).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CENELEC shall not be held responsible for identifying any or all such patent rights.
Any feedback and questions on this document should be directed to the users’ national committee. A
complete listing of these bodies can be found on the CENELEC website.
Endorsement notice
The text of the International Standard IEC 60794-1-209:2024 was approved by CENELEC as a
European Standard without any modification.
Annex ZA
(normative)
Normative references to international publications
with their corresponding European publications
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments)
applies.
NOTE 1  Where an International Publication has been modified by common modifications, indicated by (mod),
the relevant EN/HD applies.
NOTE 2  Up-to-date information on the latest versions of the European Standards listed in this annex is available
here: www.cencenelec.eu.
Publication Year Title EN/HD Year
IEC 60304 - Standard colours for insulation for low- HD 402 S2 -
frequency cables and wires
IEC 60794-1-1 - Optical fibre cables - Part 1-1: Generic EN 60794-1-1 -
specification - General
IEC 60794-1-2 - Optical fibre cables - Part 1-2: Generic EN IEC 60794-1-2 -
specification - Basic optical cable test
procedures - General guidance
IEC 60794-1-201 - Optical fibre cables - Part 1-201: Generic EN IEC 60794-1-201 -
specification - Basic optical cable test
procedures - Environmental test methods
- Temperature cycling, method F1

IEC 60794-1-209 ®
Edition 1.0 2024-05
INTERNATIONAL
STANDARD
NORME
INTERNATIONALE
Optical fibre cables –
Part 1-209: Generic specification – Basic optical cable test procedures –
Environmental test methods – Ageing, method F9
Câbles à fibres optiques –
Partie 1-209: Spécification générique – Procédures fondamentales d’essai des
câbles optiques – Méthodes d’essai d’environnement – Vieillissement, méthode
F9
INTERNATIONAL
ELECTROTECHNICAL
COMMISSION
COMMISSION
ELECTROTECHNIQUE
INTERNATIONALE
ICS 33.180.10 ISBN 978-2-8322-8962-4
– 2 – IEC 60794-1-209:2024 © IEC 2024
CONTENTS
FOREWORD . 3
INTRODUCTION . 5
1 Scope . 6
2 Normative references . 6
3 Terms and definitions . 6
4 Method F9 – Ageing . 7
4.1 Object . 7
4.2 Sample . 7
4.3 Apparatus . 7
4.4 Procedure . 7
4.5 Requirement . 7
4.6 Details to be specified . 8
4.7 Details to be reported . 8
Annex A (normative) Colour permanence . 9

IEC 60794-1-209:2024 © IEC 2024 – 3 –
INTERNATIONAL ELECTROTECHNICAL COMMISSION
____________
OPTICAL FIBRE CABLES –
Part 1-209: Generic specification – Basic optical cable test procedures –
Environmental test methods – Ageing, method F9

FOREWORD
1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of IEC is to promote international
co-operation on all questions concerning standardization in the electrical and electronic fields. To this end and
in addition to other activities, IEC publishes International Standards, Technical Specifications, Technical Reports,
Publicly Available Specifications (PAS) and Guides (hereafter referred to as "IEC Publication(s)"). Their
preparation is entrusted to technical committees; any IEC National Committee interested in the subject dealt with
may participate in this preparatory work. International, governmental and non-governmental organizations liaising
with the IEC also participate in this preparation. IEC collaborates closely with the International Organization for
Standardization (ISO) in accordance with conditions determined by agreement between the two organizations.
2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international
consensus of opinion on the relevant subjects since each technical committee has representation from all
interested IEC National Committees.
3) IEC Publications have the form of recommendations for international use and are accepted by IEC National
Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC
Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any
misinterpretation by any end user.
4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications
transparently to the maximum extent possible in their national and regional publications. Any divergence between
any IEC Publication and the corresponding national or regional publication shall be clearly indicated in the latter.
5) IEC itself does not provide any attestation of conformity. Independent certification bodies provide conformity
assessment services and, in some areas, access to IEC marks of conformity. IEC is not responsible for any
services carried out by independent certification bodies.
6) All users should ensure that they have the latest edition of this publication.
7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and
members of its technical committees and IEC National Committees for any personal injury, property damage or
other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and
expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC
Publications.
8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is
indispensable for the correct application of this publication.
9) IEC draws attention to the possibility that the implementation of this document may involve the use of (a)
patent(s). IEC takes no position concerning the evidence, validity or applicability of any claimed patent rights in
respect thereof. As of the date of publication of this document, IEC had not received notice of (a) patent(s), which
may be required to implement this document. However, implementers are cautioned that this may not represent
the latest information, which may be obtained from the patent database available at https://patents.iec.ch. IEC
shall not be held responsible for identifying any or all such patent rights.
IEC 60794-1-209 has been prepared by subcommittee 86A: Fibres and cables, of IEC technical
committee 86: Fibre optics. It is an International Standard.
This document partially cancels and replaces IEC 60794-1-22:2017. This edition constitutes a
technical revision.
This edition includes the following significant technical changes with respect to
IEC 60794-1-22:2017:
a) the ambient temperature test condition has been defined as per IEC 60794-1-2;
b) all the maximum allowable attenuation increase values for single-mode and multimode fibres
have been deleted, and have been included in the list of details to be specified.

– 4 – IEC 60794-1-209:2024 © IEC 2024
The text of this International Standard is based on the following documents:
Draft Report on voting
86A/2443/FDIS 86A/2466/RVD
Full information on the voting for its approval can be found in the report on voting indicated in
the above table.
The language used for the development of this International Standard is English.
This document was drafted in accordance with ISO/IEC Directives, Part 2, and developed in
accordance with ISO/IEC Directives, Part 1 and ISO/IEC Directives, IEC Supplement, available
at www.iec.ch/members_experts/refdocs. The main document types developed by IEC are
described in greater detail at www.iec.ch/publications.
A list of all parts in the IEC 60794 series, published under the general title Optical fibre cables,
can be found on the IEC website.
The committee has decided that the contents of this document will remain unchanged until the
stability date indicated on the IEC website under webstore.iec.ch in the data related to the
spe
...