FprEN IEC 63522-15:2024

SLOVENSKI STANDARD
01-oktober-2023
Električni releji - Preskusi in meritve - 7-15. del: Čvrstost terminalov
Electrical relays - Tests and Measurements - Part 7-15: Robustness of Terminals
Relais électriques - Essais et mesurages - Partie 7-15: Robustesse des bornes
Ta slovenski standard je istoveten z: prEN IEC 61810-7-15:2023
ICS:
29.120.70 Releji Relays
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

94/922/CDV
COMMITTEE DRAFT FOR VOTE (CDV)
PROJECT NUMBER:
IEC 61810-7-15 ED1
DATE OF CIRCULATION: CLOSING DATE FOR VOTING:
2023-08-18 2023-11-10
SUPERSEDES DOCUMENTS:
94/814/CD, 94/909/CC
IEC TC 94 : ELECTRICAL RELAYS
SECRETARIAT: SECRETARY:
Austria Mr Bernhard Spalt
OF INTEREST TO THE FOLLOWING COMMITTEES: PROPOSED HORIZONTAL STANDARD:

Other TC/SCs are requested to indicate their interest, if
any, in this CDV to the secretary.
FUNCTIONS CONCERNED:
EMC ENVIRONMENT QUALITY ASSURANCE SAFETY
SUBMITTED FOR CENELEC PARALLEL VOTING NOT SUBMITTED FOR CENELEC PARALLEL VOTING
Attention IEC-CENELEC parallel voting
The attention of IEC National Committees, members of
CENELEC, is drawn to the fact that this Committee Draft
for Vote (CDV) is submitted for parallel voting.
The CENELEC members are invited to vote through the
CENELEC online voting system.
This document is still under study and subject to change. It should not be used for reference purposes.
Recipients of this document are invited to submit, with their comments, notification of any relevant patent rights of
which they are aware and to provide supporting documentation.
Recipients of this document are invited to submit, with their comments, notification of any relevant “In Some
Countries” clauses to be included should this proposal proceed. Recipients are reminded that the CDV stage is
the final stage for submitting ISC clauses. (SEE AC/22/2007 OR NEW GUIDANCE DOC).

TITLE:
Electrical relays – Tests and Measurements – Part 7-15: Robustness of Terminals

PROPOSED STABILITY DATE: 2025
NOTE FROM TC/SC OFFICERS:
electronic file, to make a copy and to print out the content for the sole purpose of preparing National Committee positions.
You may not copy or "mirror" the file or printed version of the document, or any part of it, for any other purpose without
permission in writing from IEC.

– 2 – IEC CDV 61810-7-15:2023 © IEC:2023
1 CONTENTS
3 FOREWORD . 3
4 1 Scope . 5
5 2 Normative references . 5
6 3 Terms and definitions . 6
7 4 Test procedure . 7
8 4.1 Purpose . 7
9 4.2 Procedure . 7
10 4.3 Conditions . 7
11 5 Evaluation . 7
12 Annex T (informative)  Test report. 8
13 Bibliography . 9
IEC CDV 61810-7-15:2023 © IEC:2023 – 3 –
15 INTERNATIONAL ELECTROTECHNICAL COMMISSION
16 ____________
18 ALL-OR-NOTHING ELECTRICAL RELAYS – TESTS AND MEASUREMENTS
20 Part 7-15: Robustness of Terminals
23 FOREWORD
24 1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising
25 all national electrotechnical committees (IEC National Committees). The object of IEC is to promote international
26 co-operation on all questions concerning standardization in the electrical and electronic fields. To this end and
27 in addition to other activities, IEC publishes International Standards, Technical Specifications, Technical Reports,
28 Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC Publication(s)”). Their
29 preparation is entrusted to technical committees; any IEC National Committee interested in the subject dealt with
30 may participate in this preparatory work. International, governmental and non-governmental organizations liaising
31 with the IEC also participate in this preparation. IEC collaborates closely with the International Organization for
32 Standardization (ISO) in accordance with conditions determined by agreement between the two organizations.
33 2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international
34 consensus of opinion on the relevant subjects since each technical committee has representation from all
35 interested IEC National Committees.
36 3) IEC Publications have the form of recommendations for international use and are accepted by IEC National
37 Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC
38 Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any
39 misinterpretation by any end user.
40 4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications
41 transparently to the maximum extent possible in their national and regional publications. Any divergence between
42 any IEC Publication and the corresponding national or regional publication shall be clearly indicated in the latter.
43 5) IEC itself does not provide any attestation of conformity. Independent certification bodies provide conformity
44 assessment services and, in some areas, access to IEC marks of conformity. IEC is not responsible for any
45 services carried out by independent certification bodies.
46 6) All users should ensure that they have the latest edition of this publication.
47 7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and
48 members of its technical committees and IEC National Committees for any personal injury, property damage or
49 other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and
50 expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC
51 Publications.
52 8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is
53 indispensable for the correct application of this publication.
54 9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of patent
55 rights. IEC shall not be held responsible for identifying any or all such patent rights.
56 IEC 61810-7 has been prepared by subcommittee WG3: Maintenance of basic relay standards,
57 of IEC technical committee 94: All-or-nothing electrical relays. It is an International Standard.
58 The text of this International Standard is based
...