EN 62150-3:2012

SLOVENSKI STANDARD
01-november-2012
$NWLYQHRSWLþQHNRPSRQHQWHLQQDSUDYH3UHVNXãHYDOQLLQPHULOQLSRVWRSNL
GHO6SUHPLQMDQMHRSWLþQHPRþL]DUDGLPHKDQVNLKPRWHQMYRSWLþQLKVSUHMHPQLNLK
LQRGGDMQRVSUHMHPQLãNLKYPHVQLNLK,(&
Fibre optic active components and devices - Test and measurement procedures - Part 3:
Optical power variation induced by mechanical disturbance in optical receptacles and
transceiver interfaces (IEC 62150-3:2012)
Aktive Lichtwellenleiter-Bauteile und -Bauelemente - Grundlegende Prüf- und
Messverfahren - Teil 3: Optische Leistungsabweichungen bedingt durch mechanische
Störungen an Schnittstellen optischer Steckverbinder und Transceivern (IEC 62150-
3:2012)
Composants et dispositifs actifs à fibres optiques - Procédures d'essais et de mesures -
Partie 3: Variation de puissance optique induite par des perturbations mécaniques dans
les interfaces d'émetteurs-récepteurs et d'embases optiques (CEI 62150-3:2012)
Ta slovenski standard je istoveten z: EN 62150-3:2012
ICS:
33.180.20 3RYH]RYDOQHQDSUDYH]D Fibre optic interconnecting
RSWLþQDYODNQD devices
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EUROPEAN STANDARD
EN 62150-3
NORME EUROPÉENNE
September 2012
EUROPÄISCHE NORM
ICS 33.180.20
English version
Fibre optic active components and devices -
Test and measurement procedures -
Part 3: Optical power variation induced by mechanical disturbance in
optical receptacles and transceiver interfaces
(IEC 62150-3:2012)
Composants et dispositifs actifs à fibres Aktive Lichtwellenleiter-Bauteile und -
optiques - Bauelemente -
Procédures d'essais et de mesures - Grundlegende Prüf- und Messverfahren -
Partie 3: Variation de puissance optique Teil 3: Optische Leistungsabweichungen
induite par des perturbations mécaniques bedingt durch mechanische Störungen in
dans les interfaces d'embases optiques et optischen Kupplungen und Transceiver-
d'émetteurs-récepteurs Schnittstellen
(CEI 62150-3:2012) (IEC 62150-3:2012)

This European Standard was approved by CENELEC on 2012-08-13. CENELEC members are bound to comply
with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard
the status of a national standard without any alteration.

Up-to-date lists and bibliographical references concerning such national standards may be obtained on
application to the CEN-CENELEC Management Centre or to any CENELEC member.

This European Standard exists in three official versions (English, French, German). A version in any other
language made by translation under the responsibility of a CENELEC member into its own language and notified
to the CEN-CENELEC Management Centre has the same status as the official versions.

CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus,
the Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany,
Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland,
Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom.

CENELEC
European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung

Management Centre: Avenue Marnix 17, B - 1000 Brussels

© 2012 CENELEC - All rights of exploitation in any form and by any means reserved worldwide for CENELEC members.
Ref. No. EN 62150-3:2012 E
Foreword
The text of document 86C/1061/FDIS, future edition 1 of IEC 62150-3, prepared by SC 86C, "Fibre optic
systems and active devices", of IEC TC 86, "Fibre optics" was submitted to the IEC-CENELEC parallel
vote and approved by CENELEC as EN 62150-3:2012.

The following dates are fixed:
(dop) 2013-05-13
• latest date by which the document has
to be implemented at national level by
publication of an identical national
standard or by endorsement
• latest date by which the national (dow) 2015-08-13

standards conflicting with the
document have to be withdrawn
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CENELEC [and/or CEN] shall not be held responsible for identifying any or all such patent
rights.
Endorsement notice
The text of the International Standard IEC 62150-3:2012 was approved by CENELEC as a European
Standard without any modification.
In the official version, for Bibliography, the following note has to be added for the standard indicated:
IEC 61300 (series) NOTE  Harmonized in EN 61300 series (not modified).

- 3 - EN 62150-3:2012
Annex ZA
(normative)
Normative references to international publications
with their corresponding European publications

The following documents, in whole or in part, are normatively referenced in this document and are
indispensable for its application. For dated references, only the edition cited applies. For undated
references, the latest edition of the referenced document (including any amendments) applies.

NOTE  When an international publication has been modified by common modifications, indicated by (mod), the relevant EN/HD
applies.
Publication Year Title EN/HD Year

IEC 61753 Series Fibre optic interconnecting devices and EN 61753 Series
passive components performance standard

IEC 61753-021-6 - Fibre optic interconnecting devices and EN 61753-021-6 -
passive components performance standard -
Part 021-6: Grade B/2 single-mode fibre optic
connectors for category O - Uncontrolled
environment
IEC 61754 Series Fibre optic connector interfaces EN 61754 Series

IEC 62150-3 ®
Edition 1.0 2012-07
INTERNATIONAL
STANDARD
NORME
INTERNATIONALE
colour
inside
Fibre optic active components and devices – Test and measurement

procedures –
Part 3: Optical power variation induced by mechanical disturbance in optical

receptacles and transceiver interfaces

Composants et dispositifs actifs à fibres optiques – Procédures d'essais et de

mesures –
Partie 3: Variation de puissance optique induite par des perturbations

mécaniques dans les interfaces d'embases optiques et d'émetteurs-récepteurs

INTERNATIONAL
ELECTROTECHNICAL
COMMISSION
COMMISSION
ELECTROTECHNIQUE
PRICE CODE
INTERNATIONALE
CODE PRIX S
ICS 33.180.20 ISBN 978-2-83220-157-2

– 2 – 62150-3 © IEC:2012
CONTENTS
FOREWORD . 4
1 Scope . 6
2 Normative references. 6
3 Terms, definitions and abbreviations . 6
3.1 Terms and definitions . 6
3.2 Abbreviations . 7
4 Measurement consideration . 7
4.1 Multiple test methods . 7
4.2 Two wiggle loss mechanisms . 7
4.2.1 Rationale for two different wiggle loss test methods. 7
4.2.2 Case A: Point of action for the ferrule . 8
4.2.3 Case B: Point of action for the plug housing . 8
5 Test method A . 8
5.1 Apparatus . 8
5.1.1 Apparatus . 8
5.1.2 Test cord . 8
5.1.3 Power meter . 8
5.1.4 Test load . 8
5.2 Test procedures for Tx interfaces . 9
5.2.1 Test procedures . 9
5.2.2 Set up . 9
5.2.3 Initial measurement . 9
5.2.4 Apply load and rotate . 9
5.2.5 Wiggle loss . 10
5.3 Test procedures for Rx interfaces and optical receptors . 10
5.3.1 Test procedures . 10
5.3.2 LOS indicator method . 10
5.3.3 Receiver optical power monitor method . 10
6 Test method B . 11
6.1 Apparatus . 11
6.1.1 Apparatus . 11
6.1.2 Test fixture and rotation mechanism . 11
6.1.3 Test cord . 11
6.1.4 Power meter . 11
6.1.5 Test load . 11
6.2 Test procedures for Tx interfaces . 11
6.2.1 Test procedures . 11
6.2.2 Set up . 12
6.2.3 Initial measurement . 12
6.2.4 Apply load . 12
6.2.5 Measurement . 12
6.2.6 Wiggle loss . 12
6.3 Test procedures for Rx interfaces and optical receptors . 13
6.3.1 Test procedures . 13
6.3.2 LOS indicator method . 13
6.3.3 Receiver optical power monitor method . 13

62150-3 © IEC:2012 – 3 –
7 Test results . 14
Annex A (normative) Load requirements . 15
Annex B (normative) Summary of test conditions . 16
Annex C (normative) Characteristics of test cord . 17
Annex D (normative) Floating tolerance . 19
Bibliography . 20

Figure 1 – Equipment setup of Method A for Tx interfaces . 9
Figure 2 – Equipment setup of Method A for Rx interfaces and optical receptors . 10
Figure 3 – Equipment setup of Method B for Tx interfaces . 12
Figure 4 – Equipment setup of Method B for Rx interface and optical receptors. 13
Figure C.1 – Wiggle test cord interface . 17
Figure D.1 – Floating tolerance . 19

Table 1 – Multiple test methods . 7
Table A.1 – Method A: Loads applied for devices using small-form-factor connector
cords (1,25 mm ferrule) .
...