Electric motor-operated tools - Dust measurement procedure - Part 2-3: Particular requirements for concrete grinders and disk-type sanders

1.1 General This European Standard specifies general requirements for the dust measurement of electric motor-operated tools supplied from mains or from batteries. This standard applies to those tools with and without dust extraction unit where dust such as mineral dust containing silica or wood dust is expected. 1.2 Types of dust Dust is a disperse distribution of solid substances in gases, particularly air, resulting from mechanical processes. According to EN 481, two size categories are to be differentiated: the inhalable dust and the respirable dust fraction. Inhalable dust refers to the entire inhalable fraction of the dust through mouth and/or nose. Respirable dust relates to the fraction of the inhalable dust that can reach the pulmonary alveoli due to its small particle size. This part of EN 50632 applies to concrete grinders and disc-type sanders.

Motorbetriebene Elektrowerkzeuge - Staubmessverfahren - Teil 2-3: Besondere Anforderungen für Betonschleifer und Schleifer mit Schleifblatt

Outils électriques à moteur - Procédure de mesure de la poussière - Partie 2-3: Exigences particulières pour les rectifieuses à béton et les ponceuses à disque

L'article de la Partie 1 est applicable avec l'exception suivante: Addition: La présente partie de l'EN 50632 s'applique aux rectifieuses à béton et aux ponceuses à disque.

Elektromotorna orodja - Postopek merjenja prahu - 2-3. del: Posebne zahteve za brusilnike betona in diskovne brusilnike

Ta evropski standard določa splošne zahteve za merjenje prahu elektromotornih orodij, ki se napajajo prek omrežja ali baterij. Ta standard se uporablja za orodja, pri katerih se pričakuje nabiranje prahu (na primer mineralnega prahu, ki vsebuje kremenico, ali lesnega prahu), ne glede na to, ali so opremljena z enoto za izločevanje prahu.
1.2 Vrste prahu
Prah je razpršena porazdelitev trdnih snovi v plinih, zlasti v zraku, do katere pride pri mehanskih postopkih. V skladu s standardom EN 481 se razlikuje med dvema kategorijama velikosti: vdihljivi in respiratorni delež prahu. Vdihljivi prah se nanaša na celoten vdihljivi delež prahu skozi usta in/ali nos. Respiratorni prah se nanaša na delež vdihljivega prahu, ki lahko zaradi majhne velikosti delcev doseže pljučne mešičke.
Ta del standarda EN 50632 se uporablja za brusilnike betona in diskaste brusilnike.

General Information

Status
Published
Publication Date
21-Jul-2016
Current Stage
9093 - Decision to confirm - Review Enquiry
Completion Date
02-Jun-2021

Relations

Buy Standard

Standard
EN 50632-2-3:2016
English language
10 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)


SLOVENSKI STANDARD
01-oktober-2016
Elektromotorna orodja - Postopek merjenja prahu - 2-3. del: Posebne zahteve za
brusilnike betona in diskovne brusilnike
Electric motor-operated electric tools - Dust measurement procedure - Part 2-3:
Particular requirements for concrete grinders and disk-type sanders
Outils électriques à moteur - Procédure de mesure de la poussière - Partie 2-3:
Exigences particulières pour les rectifieuses à béton et les ponceuses à disque
Ta slovenski standard je istoveten z: EN 50632-2-3:2016
ICS:
25.080.50 Brusilni in polirni stroji Grinding and polishing
machines
25.140.20 (OHNWULþQDRURGMD Electric tools
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EUROPEAN STANDARD EN 50632-2-3

NORME EUROPÉENNE
EUROPÄISCHE NORM
July 2016
ICS 13.040.40; 25.140.20
English Version
Electric motor-operated tools - Dust measurement procedure -
Part 2-3: Particular requirements for concrete grinders and disk-
type sanders
Outils électriques à moteur - Procédure de mesure de la Motorbetriebene Elektrowerkzeuge - Staubmessverfahren -
poussière - Partie 2-3: Exigences particulières pour les Teil 2-3: Besondere Anforderungen für Betonschleifer und
rectifieuses à béton et les ponceuses à disque Schleifer mit Schleifblatt
This European Standard was approved by CENELEC on 2016-05-03. CENELEC members are bound to comply with the CEN/CENELEC
Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC
Management Centre or to any CENELEC member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CENELEC member into its own language and notified to the CEN-CENELEC Management Centre has the
same status as the official versions.
CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic,
Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia,
Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and the United Kingdom.

European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung
CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2016 CENELEC All rights of exploitation in any form and by any means reserved worldwide for CENELEC Members.
Ref. No. EN 50632-2-3:2016 E
Contents
European foreword . 3
1 Scope . 4
2 Normative references . 4
3 Terms and definitions . 4
4 Test procedure . 4
5 Instrumentation . 8
6 Information to be reported . 8
Figures
Figure 101 — Test set-up for concrete grinders . 8
Figure 102 — A-support . 9
Figure 103 — Test set-up for sanding gypsum blocks .10
Tables
Table 101 — Operating conditions for concrete grinders . 5
Table 102 — Operating conditions for disc-type sanders when sanding gypsum blocks . 6
Table 103 — Operating conditions for disc-type sanders when sanding wood . 7
Table 104 — Operating conditions for disc-type sanders when sanding wooden floor . 7

European foreword
This document (EN 50632-2-3:2016) has been prepared by CLC/TC 116 “Safety of motor-operated
electric tools”.
The following dates are fixed:
(dop) 2017-05-03
• latest date by which this document has
to be implemented at national level by
publication of an identical national
standard or by endorsement
• latest date by which the national (dow) 2018-05-03
standards conflicting with this
document have to be withdrawn
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CENELEC [and/or CEN] shall not be held responsible for identifying any or all such
patent rights.
This European Standard is divided into three parts:
Part 1: General requirements for the dust measurement which are common to electric motor-
operated tools (for the purpose of this standard referred to simply as tools);
Part 2 or 3: Requirements for the dust measurement for particular types of tools, which either
supplement or modify the requirements given in Part 1 to account for the particular
characteristics of these specific tools.
This Part 2 is to be used in conjunction with EN 50632-1:2015.
This Part 2 supplements or modifies the corresponding clauses in EN 50632-1:2015.
This Part 2 was developed to set out requirements for the measurement of the concentration for
inhalable and respirable dust emitted by concrete grinders or disc-type sanders.
Where a particular subclause of Part 1 is not mentioned in this Part 2, that subclause applies as far as
reasonable. When this standard states "addition", "modification" or "replacement", the relevant text in
Part 1 is to be adapted accordingly.
Subclauses, tables and figures which are additional to those in Part 1 are numbered starting from 101.
This European Standard has been drafted in accordance with the CEN/CENELEC Internal
Regulations, Part 3.
The following print types are used:
- requirements proper: in roman type;
- test specifications: in italic type;
- explanatory matter: in smaller roman type.
The terms defined in Clause 3 are printed in bold typeface.
1 Scope
This clause of Part 1 is applicable except as follows:
Addition:
This part of EN 50632 applies to concrete grinders and disc-type sanders.
2 Normative references
This clause of Part 1 is applicable except as follows:
Addition:
EN 1339:2003, Concrete paving flags — Requirements and test methods
EN 12859:2011, Gypsum blocks — Definitions, requirements and test methods
3 Terms and definitions
This clause of Part 1 is applicable except as follows:
3.101
concrete grinder
tool intended for smoothing and deburring concrete surfaces by means of diamond wheels
3.102
disc-type sander
tool driving a rotating spindle on which a sanding accessory is mounted
4 Test procedure
This clause of Part 1 is applicable except as follows:
4.3 Operating conditions
Addition:
Concrete grinders are tested under load observing the condi
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.