EN 10248-1:2023

SLOVENSKI STANDARD
01-maj-2023
Vroče valjana jeklena obešala - 1. del: Tehnični dobavni pogoji
Hot-rolled steel sheet piles - Part 1: Technical delivery conditions
Warmgewalzte Spundbohlen aus Stahl - Teil 1: Technische Lieferbedingungen
Palplanches en acier laminées à chaud - Partie 1: Conditions techniques de livraison
Ta slovenski standard je istoveten z: EN 10248-1:2023
ICS:
77.140.45 Nelegirana jekla Non-alloyed steels
77.140.70 Jekleni profili Steel profiles
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EN 10248-1
EUROPEAN STANDARD
NORME EUROPÉENNE
March 2023
EUROPÄISCHE NORM
ICS 77.140.70 Supersedes EN 10248-1:1995
English Version
Hot-rolled steel sheet piles - Part 1: Technical delivery
conditions
Palplanches en acier laminées à chaud - Partie 1: Warmgewalzte Spundbohlen aus Stahl - Teil 1:
Conditions techniques de livraison Technische Lieferbedingungen
This European Standard was approved by CEN on 17 January 2023.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Türkiye and
United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2023 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 10248-1:2023 E
worldwide for CEN national Members.

Contents Page
European foreword . 4
1 Scope . 5
2 Normative references . 5
3 Terms and definitions . 6
4 Classification and designation . 6
4.1 Classification. 6
4.2 Designation . 6
5 Information to be supplied by the purchaser . 6
5.1 Mandatory information . 6
5.2 Options . 7
6 Manufacturing process . 7
6.1 Steel making process . 7
6.2 Delivery conditions . 7
7 Requirements . 7
7.1 General. 7
7.2 Chemical composition . 7
7.3 Mechanical properties . 8
7.4 Technological properties . 8
7.5 Surface properties . 9
7.6 Internal soundness . 9
7.7 Dimensions, tolerances on dimensions and shape, mass . 9
7.8 Load bearing capacity . 10
8 Inspection . 10
8.1 Type of inspection and inspection document . 10
8.2 Content of inspection document. 11
8.3 Tests to be carried out for specific inspection . 11
9 Frequency of testing and preparation of samples and test pieces . 11
9.1 Test unit . 11
9.2 Frequency of testing . 11
9.3 Preparation of samples and test pieces . 12
9.4 Identification of samples and test pieces . 13
10 Test methods . 13
10.1 Chemical analysis . 13
10.2 Mechanical tests . 13
10.3 Retests . 14
10.4 Load bearing capacity . 14
11 Marking, labelling, packaging . 15
12 Complaints . 15
13 Options . 15
Annex A (normative) Location of samples and test pieces . 19
Annex B (normative) Calculation of geometrical cross sectional properties . 20
Annex C (normative) Interlock resistance of straight web sheet piles . 21
Annex D (normative) Determination of the resistance of crimped points for U-shaped sheet
piles . 23
Annex E (normative) Interlock performance criteria . 27
Bibliography . 33

European foreword
This document (EN 10248-1:2023) has been prepared by Technical Committee CEN/TC 459/SC 3
“Structural steels other than reinforcements”, the secretariat of which is held by DIN.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by September 2023, and conflicting national standards shall
be withdrawn at the latest by September 2023.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN 10248-1:1995.
In comparison with the previous edition, the following technical modifications have been made:
a) Document was restructured;
b) Normative references were updated;
c) Grades S460 and S500 in quality GP were introduced;
d) Modification concerning the maximum values for the chemical composition;
e) Addition of 7.4.3 dedicated for hot-dip zinc-coating and 7.8 for load bearing capacity;
f) New wording for Clauses 8, 9 and 10 for inspection and testing;
g) Addition of Clause 12 on the complaints;
h) Removal of the former Annexes B and C on Euronorms and equivalent designations;
i) Addition of the Annexes B, C, D and E.
EN 10248 consists of the following parts, under the general title Hot-rolled steel sheet piles:
— Part 1: Technical delivery conditions
— Part 2: Tolerances on shape and dimensions
A further standard prEN 10375 with the title Hot-rolled steel sheet piles – General (Characteristics,
evaluation of conformity and marking) is in preparation and can be used together with EN 10248 after
publication.
Any feedback and questions on this document should be directed to the users’ national standards body.
A complete listing of these bodies can be found on the CEN website.
According to the CEN-CENELEC Internal Regulations, the national standards organisations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia,
Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland,
Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Republic of North
Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Türkiye and the United
Kingdom.
1 Scope
This document specifies the requirements for hot rolled steel sheet piles in respect of its chemical
composition, mechanical properties and conditions of delivery.
The products specified are for general, structural and civil engineering works. The types of steel sheet
piles covered by this document are: Z-shaped, U-shaped, straight web, H-shaped with their interlocking
bars. The types of interlocks and the requirements in respect of tolerances on shape and dimensions are
specified in Part 2 of this document.
2 Normative references
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments) applies.
EN 1011-2, Welding - Recommendations for welding of metallic materials - Part 2: Arc welding of ferritic
steels
EN 1990:2002, Eurocode - Basis of structural design
EN 1993-5:2007, Eurocode 3 - Design of steel structures - Part 5: Piling
EN 10020:2000, Definition and classification of grades of steel
EN 10021:2006, General technical delivery conditions for steel products
EN 10027-1, Designation systems for steels - Part 1: Steel names
EN 10027-2, Designation systems for steels - Part 2: Numerical system
EN 10079:2007, Definition of steel products
EN 10168, Steel products - Inspection documents - List of information and description
EN 10204, Metallic products - Types of inspection documents
EN 10248-2, Hot-rolled steel sheet piles - Part 2: Tolerances on shape and dimensions
CEN/TR 10261, Iron and steel - European standards for the determination of chemical composition
EN ISO 148-1, Metallic materials - Charpy pendulum impact test - Part 1: Test method (ISO 148-1)
EN ISO 377, Steel and steel products - Location and preparation of samples and test pieces for mechanical
testing (ISO 377)
EN ISO 2566-1, Steel - Conversion of elongation values - Part 1: Carbon and low-alloy steels (ISO 2566-
1:2021, Corrected version 2022-06)
EN ISO 6892-1, Metallic materials - Tensile testing - Part 1: Method of test at room temperature (ISO 6892-
1)
EN ISO 14284, Steel and iron - Sampling and preparation of samples for the determination of chemical
composition (ISO 14284)
As impacted by EN 1990:2002/A1:2005.
EN ISO 14713-2:2020, Zinc coatings - Guidelines and recommendations for the protection against corrosion
of iron and steel in structures - Part 2: Hot dip galvanizing (ISO 14713-2:2019)
3 Terms and definitio
...