EN 13611:2019/prA1
(Amendment)Safety and control devices for burners and appliances burning gaseous and/or liquid fuels - General requirements
Safety and control devices for burners and appliances burning gaseous and/or liquid fuels - General requirements
This European Standard specifies the general safety, design, construction, and performance requirements and testing of safety, control or regulating devices (hereafter referred to as controls) for burners and appliances burning one or more gaseous fuels or liquid fuels. This European Standard is applicable to controls with declared maximum inlet pressure up to and including 500 kPa and of nominal connection sizes up to and including DN 250.
This European standard specifies general product requirements for the following controls:
— automatic shut-off valves;
— automatic burner control systems;
— flame supervision devices;
— gas/air ratio controls;
— pressure regulators;
— manual taps;
— mechanical thermostats;
— multifunctional controls;
— pressure sensing devices;
— valve proving systems;
— automatic vent valves.
This European standard applies for control functions that are not covered by a specific control standard for burners and appliances burning one or more gaseous fuels or liquid fuels.
This European Standard applies also for safety accessories and pressure accessories with a product of the maximum allowable pressure PS and the volume V of less than 600 000 kPa · dm3 (6 000 bar · L) or with a product of PS and DN of less than 300 000 kPa (3 000 bar).
This European Standard applies for AC and DC supplied controls (for controls supplied by stand-alone battery system, battery systems for mobile applications or systems which are intended to be connected to DC supply networks controls see Annex I).
This European Standard is applicable to reset functions used for reset from lockout, e.g. due to ignition failure or temperature cut-out in burners and appliances (see Annex M).
This European Standard establishes methodologies for the determination of a Safety Integrity Level (SIL) and the determination of a Performance Level (PL) (see Annex J, Annex K and Annex L).
This European Standard gives guidelines for environmental aspects (see Annex N).
This European Standard does not apply to mechanical controls for use with liquid fuels.
The protection against environmental impact in open air (i.e. capable of withstanding UV radiation, wind, rain, snow, dirt deposits, condensation, ice and hoar frost (see IEV 441-11-05:2005), earthquake and external fire) is not covered by this standard.
This European Standard should be used in conjunction with the specific control standard (see Bibliography).
Sicherheits- und Regeleinrichtungen für Brenner und Brennstoffgeräte für gasförmige und/oder flüssige Brennstoffe - Allgemeine Anforderungen
Den vierten Absatz durch Folgendes ersetzen: "
Dieses Dokument gilt auch für druckhaltende Ausrüstungsteile mit einem höchsten Eingangsdruck von > 50 kPa und für Ausrüstungsteile mit Sicherheitsfunktionen. Anhang F enthält einige zusätzliche Anforderungen.
Dieses Dokument umfasst keine Aspekte von Fertigungsprozessen wie z. B. Wiederholungsprüfungen von druckhaltenden Ausrüstungsteilen.".
Équipements auxiliaires pour brûleurs et appareils utilisant des combustibles gazeux ou liquides - Exigences générales
Remplacer le 4e alinéa par ce qui suit : «
Le présent document s'applique aux accessoires sous pression soumis à une pression amont maximale > 50 kPa et aux accessoires de sécurité. Les exigences supplémentaires particulières sont spécifiées à l'Annexe F.
Le présent document ne couvre pas les aspects des procédés de fabrication, par exemple les essais d’épreuve des accessoires sous pression. »
Varnostne in nadzorne naprave za gorilnike in aparate na plin in/ali tekoča goriva - Splošne zahteve - Dopolnilo A1
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
01-oktober-2021
Varnostne in nadzorne naprave za gorilnike in aparate na plin in/ali tekoča goriva -
Splošne zahteve - Dopolnilo A1
Safety and control devices for burners and appliances burning gaseous and/or liquid
fuels - General requirements
Sicherheits- und Regeleinrichtungen für Brenner und Brennstoffgeräte für gasförmige
und/oder flüssige Brennstoffe - Allgemeine Anforderungen
Équipements auxiliaires pour brûleurs et appareils utilisant des combustibles gazeux ou
liquides - Exigences générales
Ta slovenski standard je istoveten z: EN 13611:2019/prA1
ICS:
23.060.40 Tlačni regulatorji Pressure regulators
27.060.20 Plinski gorilniki Gas fuel burners
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
DRAFT
EUROPEAN STANDARD
EN 13611:2019
NORME EUROPÉENNE
EUROPÄISCHE NORM
prA1
September 2021
ICS 23.060.40
English Version
Safety and control devices for burners and appliances
burning gaseous and/or liquid fuels - General
requirements
Équipements auxiliaires pour brûleurs et appareils Sicherheits- und Regeleinrichtungen für Brenner und
utilisant des combustibles gazeux ou liquides - Brennstoffgeräte für gasförmige und/oder flüssige
Exigences générales Brennstoffe - Allgemeine Anforderungen
This draft amendment is submitted to CEN members for enquiry. It has been drawn up by the Technical Committee CEN/TC 58.
This draft amendment A1, if approved, will modify the European Standard EN 13611:2019. If this draft becomes an amendment,
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for inclusion of
this amendment into the relevant national standard without any alteration.
This draft amendment was established by CEN in three official versions (English, French, German). A version in any other
language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC
Management Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and
United Kingdom.
Recipients of this draft are invited to submit, with their comments, notification of any relevant patent rights of which they are
aware and to provide supporting documentation.
Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without
notice and shall not be referred to as a European Standard.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2021 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 13611:2019/prA1:2021 E
worldwide for CEN national Members.
Contents Page
European foreword . 3
1 Modification to the European foreword . 4
2 Modification to 1, Scope . 4
3 Modification to 2, Normative references . 4
4 Modification to 3, Terms and definitions . 6
5 Modification to 6.1, General . 7
6 Modification to 6.3.4, Springs . 7
7 Modification to Table A.1 . 7
8 Modification to Annex F . 8
9 Modification to Annex G . 13
10 Modification to Annex H . 26
11 Modification to Annex ZA . 31
12 Modification to Annex ZB . 31
13 Modification to Annex ZC. 33
14 Modification to Bibliography . 34
European foreword
This document (EN 13611:2019/prA1:2021) has been prepared by Technical Committee CEN/TC 58
“Safety and control devices for burners and appliances burning gaseous or liquid fuels”, the secretariat of
which is held by BSI.
This document is currently submitted to CEN Enquiry.
1 Modifications to the European foreword
Replace the items d) and e) with: "
d) Annex ZA has been deleted;
e) Annex ZB has been updated;".
Add item g) and, subsequently, the following paragraph: "
g) Annex ZC has been updated with respect to Directive 2014/68/EU relating to safety accessories and
pressure accessories used in pressure equipment.
This document has been prepared under a Commission’s standardization request [TBD], and supports
essential requirements of EU Directives.".
2 Modification to Clause 1, Scope
th
Replace the 4 paragraph with: "
This document applies to pressure accessories which are subject to a maximum inlet pressure > 50 kPa
and to safety accessories. Specific additional requirements are given in Annex F.
This document does not cover aspects of manufacturing processes, e.g. proof tests of pressure
accessories.".
3 Modification to Clause 2, Normative references
Replace the Normative references with the following: "
EN 334:2019, Gas pressure regulators for inlet pressures up to 100 bar
1)
EN 377:1993, Lubricants for applications in appliances and associated controls using combustible gases
except those designed for use in industrial processes
EN 549:1994, Rubber materials for seals and diaphragms for gas appliances and gas equipment
st nd rd
EN 751-1:1996, Sealing materials for metallic threaded joints in contact with 1 , 2 and 3 family gases
and hot water — Part 1: Anaerobic jointing compounds
st nd rd
EN 751-2:1996, Sealing materials for metallic threaded joints in contact with 1 , 2 and 3 family gases
and hot water — Part 2: Non-hardening jointing compounds
st nd rd
EN 751-3:1996, Sealing materials for metallic threaded joints in contact with 1 , 2 and 3 family gases
and hot water — Part 3: Unsintered PTFE tapes
EN 1759-1:2004, Flanges and their joint — Circular flanges for pipes, valves, fittings and accessories, Class
designated — Part 1: Steel flanges, NPS 1/2 to 24
EN 1759-3:2003, Flanges and their joints — Circular flanges for pipes, valves, fittings and accessories, Class
designated — Part 3: Copper alloy flanges
EN 1759-4:2003, Flanges and their joint — Circular flanges for pipes, valves, fittings and accessories, class
designated — Part 4: Aluminium alloy flanges
1) As impacted by EN 377:1993+A1:1996.
EN 10226-1:2004, Pipe threads where pressure tight joints are made on the threads — Part 1: Taper
external threads and parallel internal threads — Dimensions, tolerances and designation
EN 10226-2:2005, Pipe threads where pressure tight joints are made on the threads — Part 2: Taper
external threads and taper internal threads — Dimensions, tolerances and designation
EN 12186:2014, Gas infrastructure — Gas pressure regulating stations for transmission and distribution —
Functional requirements
EN 12279:2000, Gas supply systems — Gas pressure regulating installations on service lines — Functional
requirements
EN 12516-2:2014, Valves — Shell design strength — Part 2: Experimental method
EN 12516-4:2014, Valves — Shell design strength — Part 4: Experimental method
EN 13555:2014, Flanges and their joints — Gasket parameters and test procedures relevant to the design
rules for gasketed circular flange connections
EN 13906-1:2013, Cylindrical helical springs made from round wire and bar — Calculation and design —
Part 1: Compression springs
EN 13906-2:2013, Cylindrical helical springs made from round wire and bar — Calculation and design —
Part 2: Extension springs
EN 13906-3:2013, Cylindrical helical springs made from round wire and bar — Calculation and design —
Part 2: Torsion springs
EN 50159:2010, Railway applications — Communication, signalling and processing systems — Safety-
related communication in transmission systems
EN 60068-2-6:2008, Environmental testing — Part 2-6: Tests — Test Fc: Vibration (sinusoidal)(IEC 60068-
2-6:2007)
EN 60384-14:2013, Fixed capacitors for use in electronic equipment — Part 14: Sectional specification —
Fixed capacitors for electromagnetic interference suppression and connection to the supply mains (IEC
60384-14:2010)
EN 60384-16:2005, Fixed capacitors for use in electronic equipment — Part 16: Sectional specification:
Fixed metallized polypropylene film dielectric d.c. capacitors (IEC 60384-16:2005)
EN 60529:1991, Degrees of protection provided by enclosures (IP Code) (IEC 60529:1989)
EN 60730-1:2016, Automatic electrical controls — Part 1: General requirements (IEC 60730-1:2013)
EN 60747-5-2:2001, Discrete semiconductor devices and integrated circuits — Part 5-2: Optoelectronic
devices — Essential ratings and characteristics (IEC 60747-5-2:1997)
EN 60947-5-1:2004, Low-voltage switchgear and controlgear — Part 5-1: Control circuit devices and
switching elements — Electromechanical control circuit devices (IEC 60947-5-1:2003)
EN 61000-4-29:2000, Electromagnetic compatibility (EMC) — Part 4-29: Testing and measurement
techniques — Voltage dips, short interruptions and voltage variations on d.c. input power port immunity
tests (IEC 61000-4-29:2000)
EN 61508-2:2010, Functional safety of electrical/electronic/programmable electronic safety-related
systems — Part 2: Requirements for electrical/electronic/programmable electronic safety-related systems
(IEC 61508-2:2010)
EN 61508-3:2010, Functional safety of electrical/electronic/programmable electronic safety-related
systems — Part 3: Software requirements (IEC 61508-3:2010)
EN 61508-4:2010, Functional safety of electrical/electronic/programmable electronic safety-related
systems — Part 4: Definitions and abbreviations (IEC 61508-4:2010)
EN 61508-6:2010, Functional safety of electrical/electronic/programmable electronic safety-related
systems — Part 6: Guidelines on the application of IEC 61508-2 and IEC 61508-3 (IEC 61508-6:2010)
EN 61508-7:2010, Functional safety of electrical/electronic/programmable electronic safety-related
systems — Part 7: Overview of techniques and measures (IEC 61508-3:2010)
EN 61558-2-6:2009, Safety of transformers, reactors, power supply units and similar products for supply
voltages up to 1 100 V — Part 2-6: Particular requirements and tests for safety isolating transformers and
power supply units incorporating safety isolating transformers (IEC 61558-2-6:2009)
EN 61558-2-16:2009, Safety of transformers, reactors, power supply units and similar products for supply
voltages up to 1 100 V — Part 2-16: Particular requirements and tests for switch mode power supply units
and transformers for switch mode power supply units (IEC 61558-2-16:2009)
EN 61643-11:2012, Low-voltage surge protective devices — Part 11: Surge protective devices connected to
low-voltage power systems — Requirements and test methods (IEC 61643-11:2011, modified)
EN 61810-1:2015, Electromechanical elementary relays — Part 1: General and safety requirements (IEC
61810-1:2015)
EN 62061:2005, Safety of machinery — Functional safety of safety-related electrical, electronic and
programmable electronic control systems (IEC 62061:2005)
EN ISO 228-1:2003, Pipe threads where pressure-tight joints are not made on the threads — Part 1:
Dimensions, tolerances and designation (ISO 228-1:2000)
EN ISO 13849-1:2015, Safety of machinery — Safety-related parts of control systems — Part 1: General
principles for design (ISO 13849-1:2015)
ISO 37:2017, Rubber, vulcanized or thermoplastic — Determination of tensile stress-strain properties
ISO 262:1998, ISO general purpose metric screw threads — Selected sizes for screws, bolts and nuts
ISO 301:2006, Zinc alloy ingots intended for castings
ISO 815-1:2014, Rubber, vulcanized or thermoplastic — Determination of compression set — Part 1: At
ambient or elevated temperatures
ISO 1817:2015, Rubber, vulcanized or thermoplastic — Determination of the effect of liquids
ISO 7637-2:2011, Road vehicles — Electrical disturbances from conduction and coupling — Part 2:
Electrical transient conduction along supply lines only
ISO 7637-3:2016, Road vehicles — Electrical disturbances from conduction and coupling — Part 3:
Electrical transient transmission by capacitive and inductive coupling via lines other than supply lines
ISO 23529:2016, Rubber — General procedures for preparing and conditioning test pieces for physica
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.