prEN 13763-6

SLOVENSKI STANDARD
oSIST prEN 13763-6:2021
01-april-2021
Eksplozivi za civilno uporabo - Detonatorji in zakasnilniki - 6. del: Ugotavljanje
odpornosti vodnikov proti razpokanju pri nizkih temperaturah
Explosives for civil uses - Detonators and relays - Part 6: Determination of resistance to
cracking in low temperatures of leading wires
Explosivstoffe für zivile Zwecke - Zünder und Verzögerungselemente - Teil 6:
Bestimmung des Widerstandes der Isolation von Zünderdrähten gegen Rissbildung bei
niedrigen Temperaturen
Explosifs à usage civil - Détonateurs et relais - Partie 6: Détermination de la résistance à
la fissuration des fils d'amorces à basse température
Ta slovenski standard je istoveten z: prEN 13763-6
ICS:
71.100.30 Eksplozivi. Pirotehnika in Explosives. Pyrotechnics and
ognjemeti fireworks
oSIST prEN 13763-6:2021 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------
oSIST prEN 13763-6:2021

---------------------- Page: 2 ----------------------
oSIST prEN 13763-6:2021


DRAFT
EUROPEAN STANDARD
prEN 13763-6
NORME EUROPÉENNE

EUROPÄISCHE NORM

April 2021
ICS 71.100.30 Will supersede EN 13763-6:2003
English Version

Explosives for civil uses - Detonators and detonating cord
relays - Part 6: Determination of resistance to cracking in
low temperatures of leading wires
Explosifs à usage civil - Détonateurs et relais pour Explosivstoffe für zivile Zwecke - Zünder und
cordeau détonant - Partie 6: Détermination de la Sprengschnurverbinder - Teil 6: Bestimmung des
résistance à la fissuration des fils d'amorces à basse Widerstandes der Isolation von Zünderdrähten gegen
température Rissbildung bei niedrigen Temperaturen
This draft European Standard is submitted to CEN members for enquiry. It has been drawn up by the Technical Committee
CEN/TC 321.

If this draft becomes a European Standard, CEN members are bound to comply with the CEN/CENELEC Internal Regulations
which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.

This draft European Standard was established by CEN in three official versions (English, French, German). A version in any other
language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC
Management Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and
United Kingdom.

Recipients of this draft are invited to submit, with their comments, notification of any relevant patent rights of which they are
aware and to provide supporting documentation.

Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without
notice and shall not be referred to as a European Standard.


EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2021 CEN All rights of exploitation in any form and by any means reserved Ref. No. prEN 13763-6:2021 E
worldwide for CEN national Members.

---------------------- Page: 3 ----------------------
oSIST prEN 13763-6:2021
prEN 13763-6:2021 (E)
Contents Page
European foreword . 3
Introduction . 5
1 Scope . 6
2 Normative references . 6
3 Terms and definitions . 6
4 Principle . 6
5 Apparatus . 6
)
6 Preparation and handling of test samples and test pieces . 6
7 Procedure .
...