Preparation of steel substrates before application of paints and related products - Test methods for metallic blast-cleaning abrasives - Part 7: Determination of moisture (ISO 11125-7:2018)

This document specifies a test method for the determination of the level of free moisture present in metallic blast-cleaning abrasives. It is determined by measuring the mass lost on heating.
This is one of a number of parts of ISO 11125 dealing with the sampling and testing of metallic abrasives for blast-cleaning.
The types of metallic abrasive and requirements for each are contained in the various parts of ISO 11124.
The ISO 11124 and ISO 11125 series have been drafted as a coherent set of International Standards on metallic blast-cleaning abrasives. Information on all parts of both series is given in Annex A.

Vorbereitung von Stahloberflächen vor dem Auftragen von Beschichtungsstoffen - Prüfverfahren für metallische Strahlmittel - Teil 7: Bestimmung der Feuchte (ISO 11125-7:2018)

Préparation des subjectiles d'acier avant application de peintures et de produits assimilés - Méthodes d'essai pour abrasifs métalliques destinés à la préparation par projection - Partie 7: Détermination de l'humidité (ISO 11125-7:2018)

Le présent document spécifie une méthode d'essai pour la détermination du niveau d'humidité libre présente dans les abrasifs métalliques destinés à la préparation par projection. Elle est déterminée en mesurant la perte de masse par chauffage.
Ceci est l'une des parties de l'ISO 11125 qui traitent de l'échantillonnage et des essais des abrasifs métalliques destinés à la préparation par projection.
Le type d'abrasifs métalliques et les exigences pour chacun sont donnés dans les différentes parties de l'ISO 11124.
Les séries de l'ISO 11124 et l'ISO 11125 constituent une série cohérente de Normes internationales sur les abrasifs métalliques destinés à la préparation par projection. L'Annexe A donne des informations sur toutes les parties des deux séries.

Priprava jeklenih podlag pred nanašanjem barv in sorodnih premazov - Preskusne metode za kovinske granulate za peskanje - 7. del: Ugotavljanje vlage (ISO 11125-7:2018)

Ta dokument določa preskusno metodo za ugotavljanje ravni proste vlage v kovinskih granulatih za peskanje. Določi se z merjenjem mase, izgubljene zaradi ogrevanja.
To je eden od več delov standarda ISO 11125, ki obravnavajo vzorčenje in preskušanje kovinskih granulatov
za peskanje.
Vrste kovinskega granulata in zahteve za vsak granulat so določene v različnih delih standarda ISO 11124.
Skupini standardov ISO 11124 in ISO 11125 sta bili pripravljeni kot skladen sklop mednarodnih standardov za kovinske granulate za peskanje. Informacije o vseh delih obeh skupin so podane v dodatku A.

General Information

Status
Published
Publication Date
30-Oct-2018
Withdrawal Date
29-Apr-2019
Current Stage
6060 - Definitive text made available (DAV) - Publishing
Start Date
31-Oct-2018
Completion Date
31-Oct-2018

Relations

Buy Standard

Standard
EN ISO 11125-7:2018
English language
11 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)


SLOVENSKI STANDARD
01-december-2018
Priprava jeklenih podlag pred nanašanjem barv in sorodnih premazov - Preskusne
metode za kovinske granulate za peskanje - 7. del: Ugotavljanje vlage (ISO 11125-
7:2018)
Preparation of steel substrates before application of paints and related products - Test
methods for metallic blast-cleaning abrasives - Part 7: Determination of moisture (ISO
11125-7:2018)
Vorbereitung von Stahloberflächen vor dem Auftragen von Beschichtungsstoffen -
Prüfverfahren für metallische Strahlmittel - Teil 7: Bestimmung der Feuchte (ISO 11125-
7:2018)
Préparation des subjectiles d'acier avant application de peintures et de produits
assimilés - Méthodes d'essai pour abrasifs métalliques destinés à la préparation par
projection - Partie 7: Détermination de l'humidité (ISO 11125-7:2018)
Ta slovenski standard je istoveten z: EN ISO 11125-7:2018
ICS:
25.220.10 Priprava površine Surface preparation
87.020 Postopki za nanašanje Paint coating processes
barvnih premazov
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EN ISO 11125-7
EUROPEAN STANDARD
NORME EUROPÉENNE
October 2018
EUROPÄISCHE NORM
ICS 25.220.10 Supersedes EN ISO 11125-7:1997
English Version
Preparation of steel substrates before application of paints
and related products - Test methods for metallic blast-
cleaning abrasives - Part 7: Determination of moisture
(ISO 11125-7:2018)
Préparation des subjectiles d'acier avant application de Vorbereitung von Stahloberflächen vor dem Auftragen
peintures et de produits assimilés - Méthodes d'essai von Beschichtungsstoffen - Prüfverfahren für
pour abrasifs métalliques destinés à la préparation par metallische Strahlmittel - Teil 7: Bestimmung der
projection - Partie 7: Détermination de l'humidité (ISO Feuchte (ISO 11125-7:2018)
11125-7:2018)
This European Standard was approved by CEN on 17 August 2018.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2018 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 11125-7:2018 E
worldwide for CEN national Members.

Contents Page
European foreword . 3

European foreword
This document (EN ISO 11125-7:2018) has been prepared by Technical Committee ISO/TC 35 "Paints
and varnishes" in collaboration with Technical Committee CEN/TC 139 “Paints and varnishes” the
secretariat of which is held by DIN.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by April 2019, and conflicting national standards shall be
withdrawn at the latest by April 2019.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN ISO 11125-7:1997.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia,
France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta,
Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and the United Kingdom.
Endorsement notice
The text of ISO 11125-7:2018 has been approved by CEN as EN ISO 11125-7:2018 without any
modification.
INTERNATIONAL ISO
STANDARD 11125-7
Second edition
2018-09
Preparation of steel substrates before
application of paints and related
products — Test methods for metallic
blast-cleaning abrasives —
Part 7:
Determination of moisture
Préparation des subjectiles d'acier avant application de peintures et
de produits assimilés — Méthodes d'essai pour abrasifs métalliques
destinés à la préparation par projection —
Partie 7: Détermination de l'humidité
Reference number
ISO 11125-7:2018(E)
©
ISO 2018
ISO 11125-7:2018(E)
© ISO 2018
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting
on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address
below or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Fax: +41 22 749 09 47
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland
ii © ISO 2018 – All rights reserved

ISO 11125-7:2018(E)
Contents Page
Foreword .iv
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Apparatus . 1
5 Sampling . 2
6 Procedure. 2
6.1 Test portion . 2
6.2 Determination .
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.