EN ISO 10407-2:2008

SLOVENSKI STANDARD
01-december-2008
Industrija za predelavo nafte in zemeljskega plina - Rotacijska vrtalna oprema - 2.
del: Pregled in klasifikacija sestavnih delov vrtalnega vretena (ISO 10407-2:2008)
Petroleum and natural gas industries - Rotary drilling equipment - Part 2: Inspection and
classification of used drill stem elements (ISO 10407-2:2008)
Erdöl- und Erdgasindustrie - Bohr- und Produktionsausrüstung - Teil 2: Inspektion und
Klassifizierung von Bohrstrang-Komponenten (ISO 10407-2:2008)
Industries du pétrole et du gaz naturel - Équipement de forage rotatif - Partie 2: Contrôle
et classification des éléments de garnitures de forage usagés (ISO 10407-2:2008)
Ta slovenski standard je istoveten z: EN ISO 10407-2:2008
ICS:
75.180.10 Oprema za raziskovanje in Exploratory and extraction
odkopavanje equipment
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EUROPEAN STANDARD
EN ISO 10407-2
NORME EUROPÉENNE
EUROPÄISCHE NORM
October 2008
ICS 75.180.10
English Version
Petroleum and natural gas industries - Rotary drilling equipment
- Part 2: Inspection and classification of used drill stem elements
(ISO 10407-2:2008)
Industries du pétrole et du gaz naturel - Équipement de Erdöl- und Erdgasindustrie - Bohr- und
forage rotatif - Partie 2: Contrôle et classification des Produktionsausrüstung - Teil 2: Inspektion und
éléments de garnitures de forage usagés (ISO 10407- Klassifizierung von Bohrstrang-Komponenten (ISO 10407-
2:2008) 2:2008)
This European Standard was approved by CEN on 27 September 2008.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the CEN Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as the
official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland,
France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,
Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: rue de Stassart, 36  B-1050 Brussels
© 2008 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 10407-2:2008: E
worldwide for CEN national Members.

Contents Page
Foreword.3

Foreword
This document (EN ISO 10407-2:2008) has been prepared by Technical Committee ISO/TC 67 "Materials,
equipment and offshore structures for petroleum and natural gas industries" in collaboration with Technical
Committee CEN/TC 12 “Materials, equipment and offshore structures for petroleum, petrochemical and
natural gas industries” the secretariat of which is held by AFNOR.
This European Standard shall be given the status of a national standard, either by publication of an identical
text or by endorsement, at the latest by April 2009, and conflicting national standards shall be withdrawn at the
latest by April 2009.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights.
According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following
countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Cyprus, Czech
Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia,
Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain,
Sweden, Switzerland and the United Kingdom.
Endorsement notice
The text of ISO 10407-2:2008 has been approved by CEN as a EN ISO 10407-2:2008 without any
modification.
INTERNATIONAL ISO
STANDARD 10407-2
First edition
2008-10-15
Petroleum and natural gas industries —
Rotary drilling equipment —
Part 2:
Inspection and classification of used drill
stem elements
Industries du pétrole et du gaz naturel — Équipement de forage
rotatif —
Partie 2: Contrôle et classification des éléments de garnitures de forage
usagés
Reference number
ISO 10407-2:2008(E)
©
ISO 2008
ISO 10407-2:2008(E)
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but
shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In
downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat
accepts no liability in this area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation
parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In
the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.

©  ISO 2008
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or
ISO's member body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland
ii © ISO 2008 – All rights reserved

ISO 10407-2:2008(E)
Contents Page
Foreword. vi
Introduction . vii
1 Scope .1
2 Normative references .1
3 Terms and definitions .2
4 Symbols and abbreviated terms .8
4.1 Symbols .8
4.2 Abbreviated terms .9
5 Conformance.10
5.1 Basis for inspection .10
5.2 Repeatability of results .11
5.3 Ordering information.11
6 Quality assurance.11
6.1 General.11
6.2 Standardization and operating procedures .11
6.3 Equipment description.12
6.4 Personnel qualification .12
6.5 Dynamic test data demonstrating the system capabilities for detecting the reference
indicators.12
6.6 Reports .12
7 Qualification of inspection personnel .12
7.1 General.12
7.2 Written procedure.12
7.3 Qualification responsibility and requirements .13
7.4 Training programmes.13
7.5 Examinations.13
7.6 Experience.13
7.7 Re-qualification.13
7.8 Documentation.14
7.9 NDT personnel certification.14
8 General inspection procedures.14
8.1 General.14
8.2 Owner/operator work site requirements for quality inspection.14
8.3 Documents at job site .14
8.4 Pre-inspection procedures .15
8.5 Drill-pipe and tool-joint classification markings .15
8.6 Post-inspection procedures .16
9 General non-destructive inspection method requirements .19
9.1 General.19
9.2 Equipment .19
9.3 Illumination.20
9.4 Magnetic-particle-inspection equipment.21
9.5 Ultrasonic .23
9.6 Electromagnetic inspection units .24
10 Drill stem element inspection and classification .24
10.1 Pipe body — Full-length visual inspection .24
10.2 Drill body — Outside diameter gauging .25
ISO 10407-2:2008(E)
10.3 Pipe body — Ultrasonic wall-thickness gauging. 27
10.4 Pipe body — Full-length electromagnetic inspection (EMI) . 29
10.5 Pipe body — Full-length ultrasonic transverse and wall thickness . 31
10.6 Pipe body — Full-length ultrasonic transverse, wall thickness and longitudinal inspection. 34
10.7 Drill-pipe body — External magnetic-particle inspection of the critical area . 37
...