EN 13253:2014+A1:2015
(Main)Geotextiles and geotextile-related products - Characteristics required for use in erosion control works (coastal protection, bank revetments)
Geotextiles and geotextile-related products - Characteristics required for use in erosion control works (coastal protection, bank revetments)
This European Standard specifies the relevant characteristics of geotextiles and geotextile-related products used in erosion control works for preventing the migration of fine-graded material into layers of coarser material due to alternating hydraulic gradients, and the appropriate test methods to determine these characteristics.
This European Standard covers applications in coastal protection and bank revetment. This European Standard does not cover surface erosion, where the geotextile or geotextile-related product is located at the surface.
The intended use of these geotextiles or geotextile-related products is to fulfil one or more of the following functions: filtration, separation, and reinforcement. The separation function will always occur in conjunction with filtration or reinforcement, and hence will not be specified alone.
This European Standard is not applicable to geosynthetic barriers, as defined in EN ISO 10318.
This European Standard provides for the assessment and verification of constancy of performance of the product to this European Standard and for factory production control procedures.
NOTE Particular application cases may contain requirements regarding additional properties and – preferably standardised – test methods, if they are technically relevant.
This European Standard may be used to derive design values by taking into account factors within the context of the definitions given in EN 1997 1 (Eurocode 7), e.g. factors of safety. The design life of the product should be determined, since its function may be temporary, as a construction expediency, or permanent, for the lifetime of the structure.
Geotextilien und geotextilverwandte Produkte - Geforderte Eigenschaften für die Anwendung in Erosionsschutzanlagen (Küstenschutz, Deckwerksbau)
Diese Europäische Norm legt die wichtigsten Eigenschaften von Geotextilien und geotextilverwandten Produkten, die in Erosionsschutzanlagen verwendet werden, fest, um das Abwandern von feinkörnigen Materialien in Schichten von gröberen Materialien infolge von wechselnden hydraulischen Gefällen zu verhindern, sowie die geeigneten Prüfverfahren zur Bestimmung dieser Eigenschaften fest.
Diese Europäische Norm behandelt Anwendungen in Küstenschutz und Deckwerksbau. Diese Europäische Norm behandelt jedoch nicht Oberflächenerosionsschutz, wobei das Geotextil oder geotextilverwandte Produkt sich an der Oberfläche befindet.
Bei ihrer vorgesehenen Anwendung werden diese Geotextilien und geotextilverwandten Produkte eine oder mehrere der folgenden Funktionen erfüllen: Filtern, Trennen und Bewehren. Die Trennfunktion wird immer in Verbindung mit Filtern oder Bewehren genutzt, folglich ist Trennen nie allein vorgegeben.
Diese Europäische Norm ist nicht auf geosynthetische Dichtungsbahnen anwendbar, wie in EN ISO 10318 festgelegt.
Diese Europäische Norm behandelt die Bewertung und Überprüfung der Leistungsbeständigkeit des Produkts nach dieser Europäischen Norm und die werkseigene Produktionskontrolle.
ANMERKUNG Besondere Anwendungen können Anforderungen hinsichtlich zusätzlicher Eigenschaften und – vorzugsweise genormte – Prüfverfahren enthalten, wenn diese technisch relevant sind.
Diese Europäische Norm darf zur Festlegung von Bemessungswerten herangezogen werden, in dem die im Zusammenhang mit den in EN 1997-1 (Eurocode 7) angegebenen Definitionen, z. B. Sicherheitsbeiwerte, berücksichtigt werden. Für das Produkt sollte die vorgesehene Nutzungsdauer festgelegt werden, weil seine Funktion zeitlich befristet sein darf, als Einbauhilfe, oder dauerhaft, weil sie der Nutzungsdauer des Bauwerks entspricht.
Géotextiles et produits apparentés - Caractéristiques requises pour l’utilisation dans les ouvrages de lutte contre l’érosion (protection côtière et revêtement de berge)
La présente Norme européenne spécifie les caractéristiques pertinentes des géotextiles et produits apparentés utilisés dans les ouvrages de contrôle de l’érosion dans le but de prévenir la migration de matière à granulométrie fine dans des couches de matière plus grosse sous l’influence de gradients hydrauliques alternants. Cette norme spécifie aussi les méthodes d’essai appropriées pour déterminer ces caractéristiques.
L’application de ces géotextiles ou produits apparentés est de remplir au moins l’une des fonctions suivantes : séparation, renforcement et filtration. La fonction séparation étant toujours utilisée conjointement avec une autre fonction, celle-ci ne peut être spécifiée seule.
La présente norme européenne ne s’applique pas aux géomembranes et géosynthétiques bentonitiques tels que définis dans l'EN ISO 10318.
La présente norme européenne permet d’évaluer et de vérifier la constance des performances du produit à la présente norme européenne et les procédures de contrôle de la production en usine.
Des cas d’application particuliers ou des spécifications nationales peuvent contenir des exigences sur des propriétés supplémentaires et méthodes d’essais - si possible normalisées - si elles sont techniquement pertinentes.
La présente norme européenne peut être utilisée pour déduire les valeurs de calcul en prenant en compte les facteurs définis dans l’ ENV 1997-1( Eurocode 7), par exemple les facteurs de sécurité. Il convient de déterminer la durée de vie prévue du produit, puisque sa fonction peut être provisoire, pour des besoins de construction, ou permanente, pour la durée de vie de la structure.
Geotekstilije in geotekstilijam sorodni izdelki - Značilnosti, ki se zahtevajo pri nadzoru erozije (zaščita obale, zaščita z nasipom)
Ta evropski standard določa pomembne značilnosti geotekstilij in geotekstilijam sorodnih izdelkov, ki se uporabljajo pri nadzoru erozije za preprečevanje prodiranja materiala fino stopnjevane zrnavosti v plasti bolj grobega materiala zaradi izmeničnih hidravličnih gradientov, ter ustrezne preskusne metode za določitev teh značilnosti.
Ta evropski standard zajema uporabe v zaščiti obale in zaščiti z nasipom. Ta evropski standard ne zajema površinske erozije, ko je geotekstilija in geotekstiliji sorodni izdelek na površini.
Te geotekstilije in geotekstilijam sorodni izdelki naj bi imeli eno ali več naslednjih funkcij: filtriranje, ločevanje in armiranje. Funkcija ločevanja se bo vedno pojavljala skupaj s filtriranjem ali armiranjem, zato ne bo ločeno opredeljena.
Ta evropski standard ne velja za geosintetične zapore, kakor so opredeljene v standardu EN ISO 10318.
Ta evropski standard omogoča ocenjevanje in preverjanje stalnosti delovanja izdelka v skladu s tem evropskim standardom ter postopke kontrole proizvodnje v obratu.
OPOMBA Posamezni primeri uporabe lahko vključujejo zahteve glede dodatnih lastnosti in – po možnost standardiziranih – preskusnih metod, če so tehnično pomembni.
Ta evropski standard se lahko uporablja za izpeljavo projektnih vrednosti ob upoštevanju dejavnikov v okviru definicij iz standarda EN 1997 1 (Evrokod 7), npr. dejavnikov varnosti. Določila naj bi se projektna življenjska doba izdelka, saj je njegova funkcija začasna, kot zagotavljanje primernosti za gradnjo, ali stalna, tj. za življenjsko dobo konstrukcije.
General Information
- Status
- Withdrawn
- Publication Date
- 10-Feb-2015
- Withdrawal Date
- 20-Jan-2026
- Technical Committee
- CEN/TC 189 - Geotextiles and geotextile-related products
- Drafting Committee
- CEN/TC 189/WG 1 - ad hoc group Asphalt reinforcement
- Current Stage
- 9960 - Withdrawal effective - Withdrawal
- Start Date
- 12-Oct-2016
- Completion Date
- 21-Jan-2026
Relations
- Effective Date
- 19-Jan-2023
- Effective Date
- 18-Jan-2023
- Effective Date
- 19-Oct-2016
- Effective Date
- 28-Jan-2026
- Effective Date
- 28-Jan-2026
- Effective Date
- 28-Jan-2026
- Effective Date
- 28-Jan-2026
- Effective Date
- 28-Jan-2026
- Effective Date
- 28-Jan-2026
- Effective Date
- 28-Jan-2026
- Effective Date
- 28-Jan-2026
- Effective Date
- 28-Jan-2026
- Effective Date
- 28-Jan-2026
- Effective Date
- 28-Jan-2026
- Effective Date
- 28-Jan-2026
Get Certified
Connect with accredited certification bodies for this standard
Bureau Veritas Bangladesh
Bureau Veritas certification services in Bangladesh.
ECOCERT France
Leader in organic and sustainability certification worldwide.
Hohenstein Institut
Textile testing and certification.
Sponsored listings
Frequently Asked Questions
EN 13253:2014+A1:2015 is a standard published by the European Committee for Standardization (CEN). Its full title is "Geotextiles and geotextile-related products - Characteristics required for use in erosion control works (coastal protection, bank revetments)". This standard covers: This European Standard specifies the relevant characteristics of geotextiles and geotextile-related products used in erosion control works for preventing the migration of fine-graded material into layers of coarser material due to alternating hydraulic gradients, and the appropriate test methods to determine these characteristics. This European Standard covers applications in coastal protection and bank revetment. This European Standard does not cover surface erosion, where the geotextile or geotextile-related product is located at the surface. The intended use of these geotextiles or geotextile-related products is to fulfil one or more of the following functions: filtration, separation, and reinforcement. The separation function will always occur in conjunction with filtration or reinforcement, and hence will not be specified alone. This European Standard is not applicable to geosynthetic barriers, as defined in EN ISO 10318. This European Standard provides for the assessment and verification of constancy of performance of the product to this European Standard and for factory production control procedures. NOTE Particular application cases may contain requirements regarding additional properties and – preferably standardised – test methods, if they are technically relevant. This European Standard may be used to derive design values by taking into account factors within the context of the definitions given in EN 1997 1 (Eurocode 7), e.g. factors of safety. The design life of the product should be determined, since its function may be temporary, as a construction expediency, or permanent, for the lifetime of the structure.
This European Standard specifies the relevant characteristics of geotextiles and geotextile-related products used in erosion control works for preventing the migration of fine-graded material into layers of coarser material due to alternating hydraulic gradients, and the appropriate test methods to determine these characteristics. This European Standard covers applications in coastal protection and bank revetment. This European Standard does not cover surface erosion, where the geotextile or geotextile-related product is located at the surface. The intended use of these geotextiles or geotextile-related products is to fulfil one or more of the following functions: filtration, separation, and reinforcement. The separation function will always occur in conjunction with filtration or reinforcement, and hence will not be specified alone. This European Standard is not applicable to geosynthetic barriers, as defined in EN ISO 10318. This European Standard provides for the assessment and verification of constancy of performance of the product to this European Standard and for factory production control procedures. NOTE Particular application cases may contain requirements regarding additional properties and – preferably standardised – test methods, if they are technically relevant. This European Standard may be used to derive design values by taking into account factors within the context of the definitions given in EN 1997 1 (Eurocode 7), e.g. factors of safety. The design life of the product should be determined, since its function may be temporary, as a construction expediency, or permanent, for the lifetime of the structure.
EN 13253:2014+A1:2015 is classified under the following ICS (International Classification for Standards) categories: 59.080.70 - Geotextiles. The ICS classification helps identify the subject area and facilitates finding related standards.
EN 13253:2014+A1:2015 has the following relationships with other standards: It is inter standard links to EN 13253:2014/FprA1, EN 13253:2014, EN 13253:2016, EN ISO 13426-2:2024, EN ISO 13426-1:2019, EN ISO 13433:2025, EN ISO 13431:2024, EN ISO 10722:2019, EN ISO 10319:2024, EN 12447:2021, EN ISO 3696:1995, EN ISO 10318-2:2015, EN ISO 11058:2019, EN ISO 13438:2018, EN ISO 10321:2008. Understanding these relationships helps ensure you are using the most current and applicable version of the standard.
EN 13253:2014+A1:2015 is associated with the following European legislation: EU Directives/Regulations: 305/2011; Standardization Mandates: M/107, M/386. When a standard is cited in the Official Journal of the European Union, products manufactured in conformity with it benefit from a presumption of conformity with the essential requirements of the corresponding EU directive or regulation.
EN 13253:2014+A1:2015 is available in PDF format for immediate download after purchase. The document can be added to your cart and obtained through the secure checkout process. Digital delivery ensures instant access to the complete standard document.
Standards Content (Sample)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Geotextilien und geotextilverwandte Produkte - Geforderte Eigenschaften für die Anwendung in Erosionsschutzanlagen (Küstenschutz, Deckwerksbau)Géotextiles et produits apparentés - Caractéristiques requises pour l’utilisation dans les ouvrages de lutte contre l’érosion (protection côtière et revêtement de berge)Geotextiles and geotextile-related products - Characteristics required for use in erosion control works (coastal protection, bank revetments)93.020Zemeljska dela. Izkopavanja. Gradnja temeljev. Dela pod zemljoEarthworks. Excavations. Foundation construction. Underground works59.080.70GeotekstilijeGeotextilesICS:Ta slovenski standard je istoveten z:EN 13253:2014+A1:2015SIST EN 13253:2014+A1:2015en,fr,de01-april-2015SIST EN 13253:2014+A1:2015SLOVENSKI
STANDARD
EUROPEAN STANDARD NORME EUROPÉENNE EUROPÄISCHE NORM
EN 13253:2014+A1
February 2015 ICS 59.080.70 Supersedes EN 13253:2014English Version
Geotextiles and geotextile-related products - Characteristics required for use in erosion control works (coastal protection, bank revetments)
Géotextiles et produits apparentés - Caractéristiques requises pour l'utilisation dans les ouvrages de lutte contre l'érosion (protection côtière et revêtement de berge)
Geotextilien und geotextilverwandte Produkte - Geforderte Eigenschaften für die Anwendung in Erosionsschutzanlagen (Küstenschutz, Deckwerksbau) This European Standard was approved by CEN on 9 November 2013 and includes Amendment 1 approved by CEN on 13 December 2014.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre:
Avenue Marnix 17,
B-1000 Brussels © 2015 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 13253:2014+A1:2015 ESIST EN 13253:2014+A1:2015
Factory production control . 15 A.1 Factory production control scheme . 15 A.1.1 General . 15 A.1.2 Product design . 15 A.1.3 Production . 15 A.1.4 Finished products . 15 A.1.5 Provisions applicable to A.1.2, A.1.3 and A.1.4 (to be used where appropriate) . 16 A.2 Assessment of a factory production control (FPC) system . 17 A.2.1 General . 17 A.2.2 Checklist . 17 A.2.3 Test frequency . 20 Annex B (normative)
!Durability aspects" . 22 B.1 General . 22 SIST EN 13253:2014+A1:2015
Guidelines for the selection of the appropriate standard in a specific application . 28 Annex D (informative)
Significant technical changes to the superseded standard . 30 Annex ZA (informative)
Clauses of this European Standard addressing the provisions of the EU Construction Products Regulation . 31 ZA.1 Scope and relevant characteristics . 31 ZA.2 Procedure for AVCP of Geotextiles and geotextiles-related products for the use in the construction of erosion control works . 34 ZA.2.1 Systems of AVCP . 34 ZA.2.2 Declaration of performance (DoP) . 37 ZA.3 CE marking and labelling . 40 Bibliography . 43
Determination of the resistance to weathering EN 12226, Geosynthetics
General tests for evaluation following durability testing EN 12447, Geotextiles and geotextile-related products
Screening test method for determining the resistance to hydrolysis in water EN ISO 1043-1, Plastics
Symbols and abbreviated terms
Part 1: Basic polymers and their special characteristics (ISO 1043-1) EN ISO 9862, Geosynthetics
Sampling and preparation of test specimens (ISO 9862) !EN ISO 3696, Water for analytical la" EN ISO 10318, Geosynthetics
Terms and definitions (ISO 10318) EN ISO 10319, Geosynthetics
Wide-width tensile test (ISO 10319) EN ISO 10320, Geotextiles and geotextile-related products
Identification on site (ISO 10320) EN ISO 10321, Geosynthetics
Tensile test for joints/seams by wide-width strip method (ISO 10321) SIST EN 13253:2014+A1:2015
Index test procedure for the evaluation of mechanical damage under repeated loading
Damage caused by granular material (ISO 10722) EN ISO 11058, Geotextiles and geotextile-related products
Determination of water permeability characteristics normal to the plane, without load (ISO 11058) EN ISO 12236, Geosynthetics
Static puncture test (CBR test) (ISO 12236) EN ISO 12956, Geotextiles and geotextile-related products
Determination of the characteristic opening size (ISO 12956) EN ISO 12957-1, Geosynthetics
Determination of friction characteristics
Part 1: Direct shear test (ISO 12957-1) EN ISO 12957-2, Geosynthetics
Determination of friction characteristics
Part 2: Inclined plane test (ISO 12957-2) EN ISO 13426-1, Geotextiles and geotextile-related products
Strength of internal structural junctions
Part 1: Geocells (ISO 13426-1) EN ISO 13426-2, Geotextiles and geotextile-related products
Strength of internal structural junctions
Part 2: Geocomposites (ISO 13426-2) EN ISO 13431, Geotextiles and geotextile-related products
Determination of tensile creep and creep rupture behaviour (ISO 13431) EN ISO 13433, Geosynthetics
Dynamic perforation test (cone drop test) (ISO 13433) EN ISO 13438, Geotextiles and geotextile-related products
Screening test method for determining the resistance to oxidation (ISO 13438) ISO 10390, Soil quality — Determination of pH ASTM D7409 — 07e1, Standard Test Method for Carboxyl End Group Content of Polyethylene Terephthalate (PET) Yarns ASTM D4603 — 03(2011)e1, Standard Test Method for Determining Inherent Viscosity of Poly(Ethylene Terephthalate) (PET) by Glass Capillary Viscometer 3 Terms, definitions and abbreviations 3.1 Terms and definitions For the purposes of this document, the terms and definitions given EN ISO 10318 and the following apply. 3.1.1 product geotextile or geotextile-related product 3.1.2 specification any document in which the work, functions and specific conditions of use of the product are described SIST EN 13253:2014+A1:2015
aramid — GCO-R: geocomposite reinforcement 4 Required characteristics and corresponding methods of test 4.1 General The main functions of geotextiles and geotextile-related products used in erosion control works are filtration, separation and reinforcement. If a drainage or erosion control system is integrated in the construction, the requirements of the appropriate standards shall also be fulfilled. As the separation function is always used in conjunction with another function, the separation function shall never be specified alone. The specification shall define which functions and conditions of use are relevant (see Table 1). The producer shall provide the necessary data based on the requirements and test methods specified in this European Standard, as described in 5.1. The characteristics, their relevance to the conditions of use, and the test methods to be used, are specified in Table 1. The list of characteristics in Table 1 includes those needed for regulatory purposes (H), those relevant to all conditions of use (A), and those relevant to specific conditions of use (S). The indication “–” means that the characteristic is not relevant for that function. Where, for the same property, data for more than one function shall be provided, the following ranking order shall be observed: H overrules A, A overrules S, and S overrules “–”. The functions and conditions of use, corresponding with the S-coded characteristics in Table 1, are specified in 4.3. Durability shall be assessed in accordance with the requirements of Annex B. 4.2 Selection of the appropriate standard in a specific application Guidelines for the selection of the appropriate standard in a specific application are given in Annex C. SIST EN 13253:2014+A1:2015
H: required for regulatory purposes
A: relevant to all conditions of use
S: relevant to specific conditions of use
“–”: indicates that the characteristic is not relevant for that function. a Static puncture resistance may not be relevant for some types of products, e. g. GGR, GCO-R or GST. b If the mechanical properties (tensile strength and static puncture) are coded “H” in this Table, the producer shall provide data for both. The use of only one, either tensile strength or static puncture, is sufficient in a tender specification. c The strength of internal structural junctions of geocells shall be tested in accordance with EN ISO 13426-1. d The strength of internal structural junctions of geocomposites shall be tested in accordance with EN ISO 13426-2. SIST EN 13253:2014+A1:2015
(normative)
Factory production control A.1 Factory production control scheme A.1.1 General The items to be addressed in the factory production control manual relating to the system of control, determined from 5.4, are given in A.1. The single steps of factory production control are addressed in the check-list (A.2). NOTE Manufacturers operating an FPC system, which complies with EN ISO 9001 and which addresses the provisions of this European standard are considered satisfying the FPC requirements of this European Standard. A.1.2 Product design The manufacturer shall describe how product design requirements and criteria are identified, checked, controlled and updated to be unambiguous and relevant to the use of the product and its specification. The manufacturer shall describe the communication of the product design to the internal production departments or to external subcontractors. A.1.3 Production A.1.3.1 Raw or incoming materials The manufacturer shall define the acceptance criteria of raw or incoming materials and the procedures that he operates to ensure that these are met. The manufacturer shall document by analyses and/or certificates from his suppliers that all raw or incoming materials meet the declared performance, including durability performance. A.1.3.2 Production process The relevant features of the plant and production process shall be defined giving the frequency of the inspections, checks and tests, together with the values or criteria required on equipment and on work in process. The actions to be taken when control values or criteria are not obtained shall be recorded. These records shall be available for inspection. A.1.4 Finished products A.1.4.1 Tests on the finished product The size of the samples and the frequency of sampling, together with the results obtained, shall be recorded. These records shall be available for inspection. A.1.4.2 Alternative tests Where alternative tests to the reference tests are used, details of the alternative tests and procedures together with their correlation with the reference tests shall be recorded and shall be made available for inspection. SIST EN 13253:2014+A1:2015
Design 1.1 – Has the manufacturer a description how design requirements and criteria are identified, checked, controlled and updated to be unambiguous and relevant to the use of the product and its specification? To be assessed only if claimed by the manufacturer Refer to the manufacturer's documentation. 1.2 – Has the manufacturer a description of the communication of the design to the internal production departments or to external subcontractors? To be assessed only if claimed by the manufacturer. Refer to the manufacturer's documentation. 2 Product identification and traceability 2.1 – What are the means used for the unique identification of any individual finished product? E Refer to the manufacturer's documentation. SIST EN 13253:2014+A1:2015
3 Production process control 3.1 – Are there documents which define the production process parameters which could affect quality? E Refer to the manufacturer's documentation. 3.2 –Are the standards and procedures implemented? E
3.3 – Are the specified requirements concerning process validation, including the associated personnel and equipment, documented? E Refer to the manufacturer's documentation. 4 Inspection and testing on receipt of raw materials 4.1 – Are there specification sheets concerning incoming raw materials? E Refer to the manufacturer's documentation. 4.2 – Are there documents which define what shall be done in case of non-conformance of raw materials? E Refer to the manufacturer's documentation. 4.3 – Are the nature and frequency of the evaluation of incoming raw materials described and followed? E Refer to the manufacturer's documentation. 5 Inspection and testing during manufacturing 5.1 – Are there inspections or tests during the manufacturing process with specific requirement for the results? E Refer to the manufacturer's documentation. 5.2 – Are there documents concerning inspection or testing during the manufacturing process with requirement for the results? E Refer to the manufacturer's documentation. 5.3 – Do they define what shall be done in case of non-conformance of the product with the requirements? E Refer to the manufacturer's documentation. 5.4 – Are non-conforming products isolated from conform products when they are detected during manufacturing? E Refer to the manufacturer's documentation. 5.5 – Is there a procedure for handling non-conforming products? E Refer to the manufacturer's documentation. 6 Final inspection and testing 6.1 – Are there installations, equipment and personnel for final inspection and tests? E Refer to the manufacturer's documentation.
This requirement may be fulfilled by concluding a subcontracting agreement with one or more organizations or persons having the necessary skills and equipment. SIST EN 13253:2014+A1:2015
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.
Loading comments...