EN ISO 20482:2013

SLOVENSKI STANDARD
01-junij-2014
1DGRPHãþD
SIST EN ISO 20482:2004
.RYLQVNLPDWHULDOL3ORþHYLQHLQWUDNRYL3UHVNXVJORERNHJDYOHNDSR(ULFKVHQX
,62
Metallic materials - Sheet and strip - Erichsen cupping test (ISO 20482:2013)
Metallische Werkstoffe - Bleche und Bänder - Tiefungsversuch nach Erichsen (ISO
20482:2013)
Matériaux métalliques - Tôles et bandes - Essai d'emboutissage Erichsen (ISO
20482:2013)
Ta slovenski standard je istoveten z: EN ISO 20482:2013
ICS:
77.040.10 Mehansko preskušanje kovin Mechanical testing of metals
77.140.50 3ORãþDWLMHNOHQLL]GHONLLQ Flat steel products and semi-
SROL]GHONL products
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EUROPEAN STANDARD
EN ISO 20482
NORME EUROPÉENNE
EUROPÄISCHE NORM
November 2013
ICS 77.040.10 Supersedes EN ISO 20482:2003
English Version
Metallic materials - Sheet and strip - Erichsen cupping test (ISO
20482:2013)
Matériaux métalliques - Tôles et bandes - Essai Metallische Werkstoffe - Bleche und Bänder -
d'emboutissage Erichsen (ISO 20482:2013) Tiefungsversuch nach Erichsen (ISO 20482:2013)
This European Standard was approved by CEN on 28 October 2013.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member.

This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same
status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United
Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2013 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 20482:2013 E
worldwide for CEN national Members.

Contents
Page
Foreword .3

Foreword
The text of ISO 20482:2013 has been prepared by Technical Committee ISO/TC 164 “Mechanical testing of
metals” of the International Organization for Standardization (ISO) and has been taken over as
analysis)” the secretariat of which is held by AFNOR.
This European Standard shall be given the status of a national standard, either by publication of an identical
text or by endorsement, at the latest by May 2014, and conflicting national standards shall be withdrawn at the
latest by May 2014.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN ISO 20482:2003.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the following
countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech
Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece,
Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,
Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom.
Endorsement notice
The text of ISO 20482:2013 has been approved by CEN as EN ISO 20482:2013 without any modification.

INTERNATIONAL ISO
STANDARD 20482
Second edition
2013-11-15
Metallic materials — Sheet and strip
— Erichsen cupping test
Matériaux métalliques — Tôles et bandes — Essai d’emboutissage
Erichsen
Reference number
ISO 20482:2013(E)
©
ISO 2013
ISO 20482:2013(E)
© ISO 2013
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form
or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior
written permission. Permission can be requested from either ISO at the address below or ISO’s member body in the country of
the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland
ii © ISO 2013 – All rights reserved

ISO 20482:2013(E)
Contents Page
Foreword .iv
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Symbols and designations . 1
5 Principle . 3
6 Testing equipment . 3
7 Test piece . 3
8 Test conditions . 4
9 Procedure. 4
10 Test report . 4
Annex A (informative) Recommended composition of the graphite grease.6
Bibliography . 7
ISO 20482:2013(E)
Foreword
IISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2. www.iso.org/directives
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of any
patent rights identified during the development of the document will be in the Introduction and/or on
the ISO list of patent declarations received. www.iso.org/patents
Any trade name used in this document is information given for the convenience of users and does no
...