prEN 12767

SLOVENSKI STANDARD
01-november-2013
Pasivna varnost nosilnih konstrukcij za opremo cest - Zahteve in preskusne
metode
Passive safety of support structures for road equipment - Requirements and test
methods
Passive Sicherheit von Tragkonstruktionen für die Straßenausstattung - Anforderungen
und Prüfverfahren
Ta slovenski standard je istoveten z: prEN 12767
ICS:
93.080.30 Cestna oprema in pomožne Road equipment and
naprave installations
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EUROPEAN STANDARD
DRAFT
NORME EUROPÉENNE
EUROPÄISCHE NORM
September 2013
ICS 93.080.30 Will supersede EN 12767:2007
English Version
Passive safety of support structures for road equipment -
Requirements and test methods
Passive Sicherheit von Tragkonstruktionen für die
Straßenausstattung - Anforderungen und Prüfverfahren
This draft European Standard is submitted to CEN members for enquiry. It has been drawn up by the Technical Committee CEN/TC 226.

If this draft becomes a European Standard, CEN members are bound to comply with the CEN/CENELEC Internal Regulations which
stipulate the conditions for giving this European Standard the status of a national standard without any alteration.

This draft European Standard was established by CEN in three official versions (English, French, German). A version in any other language
made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United
Kingdom.
Recipients of this draft are invited to submit, with their comments, notification of any relevant patent rights of which they are aware and to
provide supporting documentation.

Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without notice and
shall not be referred to as a European Standard.

EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2013 CEN All rights of exploitation in any form and by any means reserved Ref. No. prEN 12767:2013: E
worldwide for CEN national Members.

Contents
Page
Foreword .4
Introduction .5
1 Scope .6
2 Normative references .6
3 Terms and definitions .6
4 Abbreviations .8
5 Official language .9
6 General test parameters .9
6.1 Test site .9
6.2 Backfill . 10
6.2.1 Backfill type S, D and X . 10
6.2.2 Backfill type P . 10
6.3 Test vehicle . 11
6.3.1 Test vehicle instrumentation . 11
7 General test item parameters . 12
7.1 General test item documentation . 12
7.2 Test item selection. 12
7.2.1 Lighting column . 12
7.2.2 Sign support . 13
7.2.3 Signal support . 13
7.2.4 Utility pole . 13
7.2.5 Other support structures . 13
7.2.6 Multi-legged supports . 13
8 Test method . 14
8.1 General . 14
8.2 Impact angle . 14
8.3 Impact point . 14
8.3.1 Theoretical alignment point for single legged support structures . 14
8.3.2 Theoretical alignment point for multilegged support structures . 15
8.4 Impact speed . 19
8.5 Simplified test method for unharmful support structures. 19
9 Impact data measurement and Evaluation . 20
9.1 General . 20
9.2 Test item behaviour . 20
9.3 Vehicle behaviour . 23
9.4 Impact severity indexes . 23
9.5 Impact data to be recorded . 24
9.6 Photographic coverage . 25
10 Test report . 25
10.1 General . 25
10.2 Test data decimal rounding . 26
Annex A (normative) Data evaluation . 27
A.1 Performance classes . 27
A.2 Evaluation of speedclass . 27
A.3 Evaluation of energy absorbing categories . 28
A.4 Evaluation of occupant safety level . 28
A.5 Evaluation of collapse mode behaviour . 29
A.6 Evaluation of the direction class . 29
A.7 Additional information . 30
Annex B (normative) Range of versions . 31
B.1 General . 31
B.2 Lighting column . 31
B.2.1 Definition of range of versions . 31
B.2.2 Evaluation of the performance within a range of versions . 32
B.3 Sign support . 33
B.3.1 Definition of range of versions . 33
B.3.2 Evaluation of the performance of sign support within a range of versions . 33
B.4 Signal support . 34
B.5 Utility poles . 34
B.6 Other support structures . 34
B.7 Multi-legged supports . 34
Annex C (normative) Changed versions . 35
C.1 Changed version . 35
C.1.1 Risk evaluation . 36
C.2 Deemed to comply . 36
C.2.1 Lighting column . 36
C.2.2 Sign support . 36
C.2.3 Signal support . 36
Annex D (normative) Vehicle data . 37
D.1 Vehicle dimensions . 37
Annex E (normative) Vehicle calibration . 39
E.1 Vehicle calibration test . 39
Annex F (normative) Backfill requirements . 41
F.1 Backfill dimension and support structure positioning for S, X and D backfill types . 41
F.2 Compaction of the backfill soil . 41
F.3 Pull/Push test . 42
F.4 Standard soil, type S . 42
F.5 Fine soil, type D . 43
Annex G (informative) Test report .
...