prEN ISO 11148-13

SLOVENSKI STANDARD
01-januar-2024
Neelektrična ročna orodja - Varnostne zahteve - 13. del: Orodja za pritrjevanje
(ISO/DIS 11148-13)
Hand-held non-electric power tools - Safety requirements - Part 13: Fastener driving
tools (ISO/DIS 11148-13)
Handgehaltene nicht-elektrisch betriebene Maschinen - Sicherheitsanforderungen - Teil
13: Eintreibgeräte (ISO/DIS 11148-13:2023)
Machines portatives à moteur non électrique - Exigences de sécurité - Partie 13:
Machines à enfoncer les fixations (ISO/DIS 11148-13:2023)
Ta slovenski standard je istoveten z: prEN ISO 11148-13
ICS:
25.140.10 Pnevmatična orodja Pneumatic tools
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

DRAFT INTERNATIONAL STANDARD
ISO/DIS 11148-13
ISO/TC 118/SC 3 Secretariat: SIS
Voting begins on: Voting terminates on:
2023-11-13 2024-02-05
Hand-held non-electric power tools — Safety
requirements —
Part 13:
Fastener driving tools
Machines portatives à moteur non électrique — Exigences de sécurité —
Partie 13: Machines à enfoncer les fixations
ICS: 25.140.10
This document is circulated as received from the committee secretariat.
THIS DOCUMENT IS A DRAFT CIRCULATED
FOR COMMENT AND APPROVAL. IT IS
ISO/CEN PARALLEL PROCESSING
THEREFORE SUBJECT TO CHANGE AND MAY
NOT BE REFERRED TO AS AN INTERNATIONAL
STANDARD UNTIL PUBLISHED AS SUCH.
IN ADDITION TO THEIR EVALUATION AS
BEING ACCEPTABLE FOR INDUSTRIAL,
TECHNOLOGICAL, COMMERCIAL AND
USER PURPOSES, DRAFT INTERNATIONAL
STANDARDS MAY ON OCCASION HAVE TO
BE CONSIDERED IN THE LIGHT OF THEIR
POTENTIAL TO BECOME STANDARDS TO
WHICH REFERENCE MAY BE MADE IN
Reference number
NATIONAL REGULATIONS.
ISO/DIS 11148-13:2023(E)
RECIPIENTS OF THIS DRAFT ARE INVITED
TO SUBMIT, WITH THEIR COMMENTS,
NOTIFICATION OF ANY RELEVANT PATENT
RIGHTS OF WHICH THEY ARE AWARE AND TO
PROVIDE SUPPORTING DOCUMENTATION. © ISO 2023

ISO/DIS 11148-13:2023(E)
DRAFT INTERNATIONAL STANDARD
ISO/DIS 11148-13
ISO/TC 118/SC 3 Secretariat: SIS
Voting begins on: Voting terminates on:

Hand-held non-electric power tools — Safety
requirements —
Part 13:
Fastener driving tools
Machines portatives à moteur non électrique — Exigences de sécurité —
Partie 13: Machines à enfoncer les fixations
ICS: 25.140.10
This document is circulated as received from the committee secretariat.
THIS DOCUMENT IS A DRAFT CIRCULATED
FOR COMMENT AND APPROVAL. IT IS
© ISO 2023
ISO/CEN PARALLEL PROCESSING
THEREFORE SUBJECT TO CHANGE AND MAY
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
NOT BE REFERRED TO AS AN INTERNATIONAL
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on STANDARD UNTIL PUBLISHED AS SUCH.
the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below
IN ADDITION TO THEIR EVALUATION AS
or ISO’s member body in the country of the requester. BEING ACCEPTABLE FOR INDUSTRIAL,
TECHNOLOGICAL, COMMERCIAL AND
ISO copyright office
USER PURPOSES, DRAFT INTERNATIONAL
CP 401 • Ch. de Blandonnet 8
STANDARDS MAY ON OCCASION HAVE TO
BE CONSIDERED IN THE LIGHT OF THEIR
CH-1214 Vernier, Geneva
POTENTIAL TO BECOME STANDARDS TO
Phone: +41 22 749 01 11
WHICH REFERENCE MAY BE MADE IN
Reference number
Email: copyright@iso.org
NATIONAL REGULATIONS.
Website: www.iso.org ISO/DIS 11148-13:2023(E)
RECIPIENTS OF THIS DRAFT ARE INVITED
Published in Switzerland
TO SUBMIT, WITH THEIR COMMENTS,
NOTIFICATION OF ANY RELEVANT PATENT
RIGHTS OF WHICH THEY ARE AWARE AND TO
ii
PROVIDE SUPPORTING DOCUMENTATION. © ISO 2023

ISO/DIS 11148-13:2023(E)
Contents Page
Foreword .v
Introduction . vi
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 2
3.1 General terms . 2
3.2 Terms and definitions related to fastener driving tools . 3
4 Safety requirements and measures.8
4.1 General . 8
4.2 Mechanical safety . 8
4.2.1 Protection against points and edges of fasteners . 8
4.2.2 Prevention of unintended ejection of fasteners. 8
4.2.3 Prevention of free flight of fasteners . 9
4.2.4 Design of the workpiece contact . 9
4.2.5 Permitted trigger actuation modes . 11
4.2.6 Strength of the fastener driving tool .12
4.2.7 Surfaces, edges and corners .12
4.2.8 Stability . 12
4.2.9 Hose fittings . 12
4.2.10 Unintentional change of actuation mode .12
4.3 Electrical safety .13
4.4 Thermal safety. 13
4.4.1 Hot surfaces .13
4.4.2 Cold surfaces . 13
4.5 Noise reduction . 13
4.6 Mechanical impact (vibration/recoil) . 13
4.7 Materials and substances processed, used or emitted . 14
4.7.1 Collating material residues . 14
4.7.2 Discharged air, gas and lubricants . 14
4.8 Ergonomics . 14
4.8.1 Weight and control of the tool . 14
4.8.2 Handle design . 15
4.9 User information . 15
4.9.1 Tool markings .15
4.9.2 Tool operating instructions . 15
4.10 Fire and explosion . 15
4.10.1 Hazardous energy supplies for pneumatic tools . 15
4.10.2 Release of flammable gas from gas tools and gas containers .15
4.10.3 Rupture due to high temperatures in the tool . 16
5 Verification .16
5.1 General . 16
5.2 Protection against mechanical hazards. 16
5.2.1 Protection against points and edges of fasteners . 16
5.2.2 Prevention of unintended ejection of fasteners. 16
5.2.3 Prevention of free flight of fasteners . 17
5.2.4 Design of the workpiece contact . 17
5.2.5 Actuation modes . 18
5.2.6 Strength of the fastener driving tool . 21
5.2.7 Surfaces, edges and corners . 22
5.2.8 Stability . 22
5.2.9 Hose Fittings .22
5.2.10 Unintentional change of actuation mode . 22
iii
ISO/DIS 11148-13:2023(E)
5.2.11 Strength of the fastener driving tool . 22
5.2.12 Surfaces, edges and corners . 23
5.2.13 Stability . 23
5.2.14 Hose Fittings .23
5.2.15 Unintentional change of actuation mode . 23
5.3 Electrical safety .23
5.4 Thermal safety. 23
5.4.1 Hot surfaces .
...