EN 6126:2018
(Main)Aerospace series - Fitting end, 24° internal cone, external thread, flareless type, size -32 tube diameter D=2 inches (D=50,8 mm) extra fine thread pitch inch series - Inch series - Design standard
Aerospace series - Fitting end, 24° internal cone, external thread, flareless type, size -32 tube diameter D=2 inches (D=50,8 mm) extra fine thread pitch inch series - Inch series - Design standard
This European Standard specifies the dimensions, tolerances and the required characteristics of a fitting end, 24° cone, external thread, flareless type, size −32 for use in hydraulic and fluid systems at 220 psi, diameter D = 2 inches (D = 50,8 mm) for aerospace applications.
This is a design standard, not valid for order.
This fitting can not be used for plug in union.
Luft- und Raumfahrt - Anschlussstück, Innenkonus 24°, Außengewinde, nicht gebördelt, Größe -32, Rohrdurchmesser D=2 inches (D=50,8 mm) Extrafeingewindesteigung - Inch-Reihe - Konstruktionsnorm
Série aérospatiale - Raccord, cône interne à 24°, filetage externe, de type sans épanoui et dimension -32 diamètre du tube D=2 inches (D=50,8 mm) filetage à pas extra fin - Série en inches - Norme de conception
Aeronavtika - Končnik, notranji stožec 24°, zunanji navoj, nerobljen, velikost -32 premer cevi D=2 inches (D=50,8 mm), dodatna serija finih palčnih mer - Palčne mere - Standard za projektiranje
Ta evropski standard določa dimenzije, tolerance in zahtevane lastnosti končnikov (stožec 24°, zunanji navoj, nerobljen, velikost –32) za uporabo v hidravličnih in tekočinskih sistemih pri 220 psi, premer D = 2 palca (D = 50,8 mm), ki se uporabljajo v aeronavtiki.
To je standard za zasnovo in ni veljaven za naročilo.
Tega končnika ni mogoče uporabiti za vtično zvezo.
General Information
Standards Content (Sample)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Luft- und Raumfahrt - Anschlussstück, Innenkonus 24°, Aussengewinde, nicht gebördelt, Größe -32 rohrdurchmesser D=2 inches (D=50,8 mm) Extrafeingewindesteigerung - Inch Reihe - KonstruktionsnormSérie aérospatiale - Raccord, cône interne à 24°, filetage externe, de type sans épanoui et dimension -32 diamètre du tube D=2 inches (D=50,8 mm) filetage à pas extra fin - Série en inches - Norme de conceptionAerospace series - Fitting end, 24° internal cone, external thread, flareless type, size -32 tube diameter D=2 inches (D=50,8 mm) extra fine thread pitch inch series - Inch series - Design standard49.080Aerospace fluid systems and componentsICS:Ta slovenski standard je istoveten z:EN 6126:2018SIST EN 6126:2018en,fr,de01-november-2018SIST EN 6126:2018SLOVENSKI
STANDARD
EUROPEAN STANDARD NORME EUROPÉENNE EUROPÄISCHE NORM
EN 6126
August
t r s z ICS
v {ä r z r English Version
Aerospace series æ Fitting endá
t v ¹ internal coneá external threadá flareless typeá size æ u t tube diameter D é t inches series æ Design standard Série aérospatiale æ Raccordá cône interne à
t v ¹á filetage externeá de type sans épanoui et dimension æ u t pas extra fin æ Série en inches æ Norme de conception
Luftæ und Raumfahrt æ Anschlussstücká Innenkonus
t v ¹á Außengewindeá nicht gebördeltá Größe æ u tá Extrafeingewindesteigung æ InchæReihe æ Konstruktionsnorm This European Standard was approved by CEN on
t t January
t r s zä
egulations which stipulate the conditions for giving this European Standard the status of a national standard without any alterationä Upætoædate lists and bibliographical references concerning such national standards may be obtained on application to the CENæCENELEC Management Centre or to any CEN memberä
translation under the responsibility of a CEN member into its own language and notified to the CENæCENELEC Management Centre has the same status as the official versionsä
CEN members are the national standards bodies of Austriaá Belgiumá Bulgariaá Croatiaá Cyprusá Czech Republicá Denmarká Estoniaá Finlandá Former Yugoslav Republic of Macedoniaá Franceá Germanyá Greeceá Hungaryá Icelandá Irelandá Italyá Latviaá Lithuaniaá Luxembourgá Maltaá Netherlandsá Norwayá Polandá Portugalá Romaniaá Serbiaá Slovakiaá Sloveniaá Spainá Swedená Switzerlandá Turkey and United Kingdomä
EUROPEAN COMMITTEE FOR STANDARDIZATION COMITÉ EUROPÉEN DE NORMALISATION EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre:
Rue de la Science 23,
B-1040 Brussels
t r s z CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Membersä Refä Noä EN
x s t xã t r s z ESIST EN 6126:2018
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.