EN 13251:2016
(Main)Geotextiles and geotextile-related products - Characteristics required for use in earthworks, foundations and retaining structures
Geotextiles and geotextile-related products - Characteristics required for use in earthworks, foundations and retaining structures
This European Standard specifies the relevant characteristics of geotextiles and geotextile-related products used in the construction of earthworks, foundations and retaining structures, and the appropriate test methods to determine these characteristics.
The intended use of these geotextiles or geotextile-related products is to fulfil one or more of the following functions: filtration, separation, and reinforcement. The separation function will always occur in conjunction with filtration or reinforcement, and hence will not be specified alone.
This European Standard is not applicable to geosynthetic barriers, as defined in EN ISO 10318 1.
This European Standard provides for the assessment and verification of constancy of performance of the product to this European Standard and for factory production control procedures.
Particular application cases may contain requirements regarding additional properties and – preferably standardized – test methods, if they are technically relevant.
This European Standard may be used to derive design values by taking into account factors within the context of the definitions given in EN 1997 1 (Eurocode 7), e.g. factors of safety. The design life of the product should be determined, since its function may be temporary, as a construction expediency, or permanent, for the lifetime of the structure.
Geotextilien und geotextilverwandte Produkte - Geforderte Eigenschaften für die Anwendung im Erd- und Grundbau sowie in Stützbauwerken
Diese Europäische Norm legt die wichtigsten Eigenschaften von Geotextilien und geotextilverwandten Produkten, die im Erd- und Grundbau sowie in Stützbauwerken verwendet werden, sowie die geeigneten Prüfverfahren zur Bestimmung dieser Eigenschaften fest.
Bei ihrer vorgesehenen Anwendung werden diese Geotextilien und geotextilverwandten Produkte eine oder mehrere der folgenden Funktionen erfüllen: Filtern, Trennen und Bewehren. Die Trennfunktion wird immer in Verbindung mit Filtern oder Bewehren genutzt, folglich ist Trennen nie allein vorgegeben.
Diese Europäische Norm ist nicht auf geosynthetische Dichtungsbahnen anwendbar, wie in EN ISO 10318-1 festgelegt.
Diese Europäische Norm behandelt die Bewertung und Überprüfung der Leistungsbeständigkeit des Produkts nach dieser Europäischen Norm und Verfahren für die werkseigene Produktionskontrolle.
Besondere Anwendungen können Anforderungen hinsichtlich zusätzlicher Eigenschaften und - vorzugsweise genormte - Prüfverfahren enthalten, wenn diese technisch relevant sind.
Diese Europäische Norm darf zur Festlegung von Bemessungswerten herangezogen werden, in dem die im Zusammenhang mit den in EN 1997-1 (Eurocode 7) angegebenen Definitionen berücksichtigt werden, z. B. Sicherheitsbeiwerte,. Für das Produkt sollte die Bemessungsdauer festgelegt werden, weil seine Funktion zeitlich befristet sein darf, als Einbauhilfe, oder dauerhaft, der Lebensdauer des Bauwerks entsprechend.
Géotextiles et produits apparentés - Caractéristiques requises pour l'utilisation dans les travaux de terrassement, les fondations et les structures de soutènement
La présente Norme européenne spécifie les caractéristiques pertinentes des géotextiles et produits apparentés utilisés dans les travaux de terrassement, les fondations et les structures de soutènement, ainsi que les méthodes d'essai appropriées pour déterminer ces caractéristiques.
L'utilisation prévue de ces géotextiles ou produits apparentés est de remplir au moins l'une des fonctions suivantes : filtration, séparation et renforcement. La fonction séparation étant toujours utilisée conjointement avec une filtration ou un renforcement, celle-ci n'est pas spécifiée seule.
La présente Norme européenne ne s'applique pas aux géomembranes et géosynthétiques bentonitiques tels que définis dans l'EN ISO 10318 1.
La présente Norme européenne permet d'évaluer et de vérifier la constance des performances du produit à la présente Norme européenne et les procédures de contrôle de la production en usine.
Des cas d'application particuliers peuvent contenir des exigences sur des propriétés supplémentaires et méthodes d'essai – si possible normalisées – si elles sont techniquement pertinentes.
La présente Norme européenne peut être utilisée pour déduire les valeurs de calcul en prenant en compte les facteurs définis dans l'EN 1997 1 (Eurocode 7), par exemple les facteurs de sécurité. Il convient de déterminer la durée de vie prévue du produit, puisque sa fonction peut être provisoire, pour des besoins de construction, ou permanente, pour la durée de vie de la structure.
Geotekstilije in geotekstilijam sorodni izdelki - Značilnosti, ki se zahtevajo pri nasipih, temeljih in trdnih strukturah
Ta evropski standard določa pomembne značilnosti geotekstilij in geotekstilijam sorodnih izdelkov, ki se uporabljajo pri gradnji nasipov, temeljev in trdnih struktur, ter ustrezne preskusne metode za določitev teh značilnosti.
Te geotekstilije in geotekstilijam sorodni izdelki naj bi imeli eno ali več naslednjih funkcij: filtriranje, ločevanje in ojačitev. Funkcija ločevanja se bo vedno pojavljala skupaj s filtriranjem ali ojačitvijo, zato ne bo ločeno opredeljena.
Ta evropski standard se ne uporablja za geosintetične zapore, kakor so opredeljene v standardu EN ISO 10318.
Ta evropski standard omogoča ocenjevanje in preverjanje stalnosti funkcionalnosti izdelka v skladu s tem evropskim standardom ter postopke kontrole proizvodnje v obratu.
OPOMBA: Posamezni primeri uporabe lahko vključujejo zahteve glede dodatnih lastnosti in – po možnosti standardiziranih – preskusnih metod, če so tehnično pomembni.
Ta evropski standard se lahko uporablja za izpeljavo projektnih vrednosti ob upoštevanju dejavnikov v okviru definicij iz standarda EN 1997 1 (Evrokod 7), npr. dejavnikov varnosti. Določila naj bi se projektna življenjska doba izdelka, saj je njegova funkcija začasna, kot zagotavljanje primernosti za gradnjo, ali stalna, tj. za življenjsko dobo konstrukcije.
General Information
Relations
Standards Content (Sample)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Geotextilien und geotextilverwandte Produkte - Geforderte Eigenschaften für die Anwendung im Erd- und Grundbau sowie in StützbauwerkenGéotextiles et produits apparentés - Caractéristiques requises pour l'utilisation dans les travaux de terrassement, les fondations et les structures de soutènementGeotextiles and geotextile-related products - Characteristics required for use in earthworks, foundations and retaining structures93.020Zemeljska dela. Izkopavanja. Gradnja temeljev. Dela pod zemljoEarthworks. Excavations. Foundation construction. Underground works59.080.70GeotekstilijeGeotextilesICS:Ta slovenski standard je istoveten z:EN 13251:2016SIST EN 13251:2016en,fr,de01-december-2016SIST EN 13251:2016SLOVENSKI
STANDARDSIST EN 13251:2014+A1:20151DGRPHãþD
EUROPEAN STANDARD NORME EUROPÉENNE EUROPÄISCHE NORM
EN 13251
October
t r s x ICS
w {ä r z rä y r Supersedes EN
s u t w sã t r s v ªA sã t r s wEnglish Version
Geotextiles and geotextileærelated products æ Characteristics required for use in earthworksá foundations and retaining structures Géotextiles et produits apparentés æ Caractéristiques requises pour l 5utilisation dans les travaux de terrassementá les fondations et les structures de soutènement
Geotextilien und geotextilverwandte Produkte æ Geforderte Eigenschaften für die Anwendung im Erdæ und Grundbau sowie in Stützbauwerken This European Standard was approved by CEN on
v June
t r s xä
egulations which stipulate the conditions for giving this European Standard the status of a national standard without any alterationä Upætoædate lists and bibliographical references concerning such national standards may be obtained on application to the CENæCENELEC Management Centre or to any CEN memberä
translation under the responsibility of a CEN member into its own language and notified to the CENæCENELEC Management Centre has the same status as the official versionsä
CEN members are the national standards bodies of Austriaá Belgiumá Bulgariaá Croatiaá Cyprusá Czech Republicá Denmarká Estoniaá Finlandá Former Yugoslav Republic of Macedoniaá Franceá Germanyá Greeceá Hungaryá Icelandá Irelandá Italyá Latviaá Lithuaniaá Luxembourgá Maltaá Netherlandsá Norwayá Polandá Portugalá Romaniaá Slovakiaá Sloveniaá Spainá Swedená Switzerlandá Turkey andUnited Kingdomä
EUROPEAN COMMITTEE FOR STANDARDIZATION COMITÉ EUROPÉEN DE NORMALISATION EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre:
Avenue Marnix 17,
B-1000 Brussels
t r s x CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Membersä Refä Noä EN
s u t w sã t r s x ESIST EN 13251:2016
Factory production control (FPC) . 15 A.1 Factory production control scheme . 15 A.1.1 General . 15 A.1.2 Product design . 15 A.1.3 Production . 15 A.1.4 Finished products . 15 A.1.5 Provisions applicable to A.1.2, A.1.3 and A.1.4 (to be used where appropriate) . 16 A.2 Assessment of a factory production control (FPC) system. 17 A.2.1 General . 17 A.2.2 Checklist . 17 SIST EN 13251:2016
Durability aspects . 22 B.1 General . 22 B.1.1 Service life . 22 B.1.2 Initial and repeat testing of durability. 22 B.1.3 Use of rework material . 23 B.2 Weathering (all products) . 23 B.3 Products used in non-reinforcing applications and with service lives up to 5 years . 23 B.4 Other applications and service lives up to 25 years, 50 years and 100 years . 24 B.4.1 General . 24 B.4.2 Tests for specific materials . 24 Annex C (informative)
Guidelines for the selection of the appropriate standard in a specific application . 28 Annex D (informative)
Significant technical changes to superseded versions of this standard . 30 Annex ZA (informative)
Clauses of this European Standard addressing the provisions of the EU Construction Products Regulation . 31 ZA.1 Scope and relevant characteristics . 31 ZA.2 Procedure for AVCP of Geotextiles and geotextiles-related products for the use in the construction of earthworks, foundations and retaining structures . 36 ZA.2.1 Systems of AVCP . 36 ZA.2.2 Declaration of performance (DoP) . 39 ZA.3 CE marking and labelling . 43 Bibliography . 44
A: relevant to all conditions of use
S: relevant to specific conditions of use
“–”: indicates that the characteristic is not relevant for that function. SIST EN 13251:2016
Static puncture resistance may not be relevant for some types of products, e.g. GGR, GCO-R or GST. b
If the mechanical properties (tensile strength and static puncture) are coded “A” in this Table, the use of only one, either tensile strength or static puncture, is usually sufficient in a project specification. c
The strength of internal structural junctions of geocells shall be tested in accordance with EN ISO 13426-1. d
The strength of internal structural junctions of geocomposites shall be tested in accordance with EN ISO 13426-2. SIST EN 13251:2016
For the durability aspects, see Table 1 and Annex B. The results of PTD tests shall be recorded and be available for inspection. The sample for the PTD tests shall be drawn according to EN ISO 9862 from a normal production run using the same materials and forming processes as used for the full production process. The size of the sample shall be big enough to allow the determination of the characteristics specified in Table 2. Handmade samples, short trial batches and other development prototypes may be tested by the same methods, but shall not be used for establishing characteristic values in PTD tests. 5.4 Factory production control (FPC) A FPC scheme shall be established and documented in a manual prior to a product type being placed on the market. Subsequently, any fundamental changes in raw materials and additives, manufacturing procedures or the control scheme that affect the properties or use of a product shall be recorded in the manual. The manual shall include the FPC procedures relevant to the declared properties, as confirmed by the product type determination. The FPC procedures shall consist of a permanent internal production control system to ensure that such products comply with this European Standard and that the measured values conform to the declared values. Annex A (normative) lists all the items that shall be considered to determine the appropriate control measures for a product. The manufacturer shall establish control measures for the relevant items and record them in his FPC manual. These measures shall be described in detail, including the type of tests to be performed and the frequency of these tests (see also A.2). When relevant, the procedure given in A.2.3 shall be used to check the conformity of the product for one or more characteristics. 5.5 Verification of values If verification of values is required, the compliance of characteristics with the values defined in 5.2 shall be based on measurements made on two representative samples (A and B), taken from two different rolls. Sampling shall be made in accordance with EN ISO 9862. For on-site quality control purposes CEN/TR 15019 may also be considered. The characteristics given in Table 2 shall be measured in accordance with the corresponding European Standards on specimens prepared from sample A. If the test result(s) for a particular characteristic is (are) within the tolerance value(s) given by the manufacturer, the product is accepted as complying with respect to this characteristic. If the test result(s) for a particular characteristic is (are) outside 1,5 times the tolerance value(s), the product does not comply with respect to that characteristic. If the test result(s) for a particular characteristic is (are) within 1 and 1,5 times the tolerance value(s), specimens prepared from sample B shall be tested. If the test result(s) of the sample B specimens for the same characteristic is (are) within the given tolerance value(s), the product is accepted as complying with respect to that characteristic. If the test result(s) is (are) outside the tolerance value(s), the product is not accepted. SIST EN 13251:2016
Factory production control (FPC) A.1 Factory production control scheme A.1.1 General The items to be addressed in the factory production control manual relating to the system of control, determined from 5.4, are given in A.1. The single steps of factory production control are addressed in the check-list (A.2). NOTE Manufacturers operating an FPC system, which complies with EN ISO 9001 and which addresses the provisions of this European Standard, are considered to be able to satisfy the FPC requirements of this standard. A.1.2 Product design The manufacturer shall describe how product design requirements and criteria are identified, checked, controlled and updated to be unambiguous and relevant to the use of the product and its specification. The manufacturer shall describe the communication of the product design to the internal production departments or to external subcontractors. A.1.3 Production A.1.3.1 Raw or incoming materials The manufacturer shall define the acceptance criteria of raw or incoming materials and the procedures that he operates to ensure that these are met. The manufacturer shall document by analyses and/or certificates from his suppliers that all raw or incoming materials meet the declared performance, including durability performance. A.1.3.2 Production process The relevant features of the plant and production process shall be defined giving the frequency of the inspections, checks and tests, together with the values or criteria required on equipment and on work in process. The actions to be taken when control values or criteria are not obtained shall be recorded. These records shall be available for inspection. A.1.4 Finished products A.1.4.1 Tests on the finished product The size of the samples and the frequency of sampling, together with the results obtained, shall be recorded. These records shall be available for inspection. A.1.4.2 Alternative tests Where alternative tests to the reference tests are used, details of the alternative tests and procedures together with their correlation with the reference tests shall be recorded and shall be made available for inspection. SIST EN 13251:2016
Design 1.1 – Has the manufacturer a description how design requirements and criteria are identified, checked, controlled and updated to be unambiguous and relevant to the use of the product and its specification? To be assessed only if claimed by the manufacturer Refer to the manufacturer's documentation. 1.2 – Has the manufacturer a description of the communication of the design to the internal production departments or to external subcontractors? To be assessed only if claimed by the manufacturer. Refer to the manufacturer's documentation. 2 Product identification and traceability 2.1 – What are the means used for the unique identification of any individual finished product ? E Refer to the manufacturer's documentation. 2.2 – Is it possible to identify and check date, E Refer to the manufacturer's SIST EN 13251:2016
3 Production process control 3.1 – Are there documents which define the production process parameters which could affect quality? E Refer to the manufacturer's documentation. 3.2 – Are the standards and procedures implemented? E
3.3 – Are the specified requirements concerning process validation, including the associated personnel and equipment, documented? E Refer to the manufacturer's documentation. 4 Inspection and testing on receipt of raw materials 4.1 – Are there specification sheets concerning incoming raw materials? E Refer to the manufacturer's documentation. 4.2 – Are there documents which define what shall be done in case of non-conformance of raw materials? E Refer to the manufacturer's documentation. 4.3 – Are the nature and frequency of the evaluation of incoming raw materials described and followed? E Refer to the manufacturer's documentation. 5 Inspection and testing during manufacturing 5.1 – Are there inspections or tests during the manufacturing process with specific requirement for the results? E Refer to the manufacturer's documentation. 5.2 – Are there documents concerning inspection or testing during the manufacturing process with requirement for the results? E Refer to the manufacturer's documentation. 5.3 – Do they define what shall be done in case of non-conformance of the product with the requirements? E Refer to the manufacturer's documentation. 5.4 – Are non-conforming products isolated from conform products when they are detected during manufacturing? E Refer to the manufacturer's documentation. 5.5 – Is there a procedure for handling non-conforming products? E Refer to the manufacturer's documentation. 6 Final inspection and testing 6.1 – Are there installations, equipment and personnel for final inspection and tests? E Refer to the manufacturer's documentation. This requirement may be fulfilled by concluding a subcontracting SIST EN 13251:2016
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.
Loading comments...