EN 10249-1:2023

SLOVENSKI STANDARD
oSIST prEN 10249-1:2022
01-april-2022
Hladno oblikovana jeklena obešala - 1. del: Tehnični dobavni pogoji
Cold formed steel sheet piles - Part 1: Technical delivery conditions
Kaltgeformte Spundbohlen aus Stahl - Teil 1: Technische Lieferbedingungen
Palplanches profilées à froid en acier - Partie 1 : Conditions techniques de livraison
Ta slovenski standard je istoveten z: prEN 10249-1
ICS:
77.140.45 Nelegirana jekla Non-alloyed steels
77.140.70 Jekleni profili Steel profiles
oSIST prEN 10249-1:2022 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

oSIST prEN 10249-1:2022
oSIST prEN 10249-1:2022
DRAFT
EUROPEAN STANDARD
prEN 10249-1
NORME EUROPÉENNE
EUROPÄISCHE NORM
February 2022
ICS 77.140.70 Will supersede EN 10249-1:1995
English Version
Cold formed steel sheet piles - Part 1: Technical delivery
conditions
Palplanches profilées à froid en acier - Partie 1 : Kaltgeformte Spundbohlen aus Stahl - Teil 1:
Conditions techniques de livraison Technische Lieferbedingungen
This draft European Standard is submitted to CEN members for enquiry. It has been drawn up by the Technical Committee
CEN/TC 459/SC 3.
If this draft becomes a European Standard, CEN members are bound to comply with the CEN/CENELEC Internal Regulations
which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.

This draft European Standard was established by CEN in three official versions (English, French, German). A version in any other
language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC
Management Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and
United Kingdom.
Recipients of this draft are invited to submit, with their comments, notification of any relevant patent rights of which they are
aware and to provide supporting documentation.

Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without
notice and shall not be referred to as a European Standard.

EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2022 CEN All rights of exploitation in any form and by any means reserved Ref. No. prEN 10249-1:2022 E
worldwide for CEN national Members.

oSIST prEN 10249-1:2022
prEN 10249-1:2022 (E)
Contents Page
European foreword . 3
1 Scope . 4
2 Normative references . 4
3 Terms and definitions . 5
4 Classification and designation . 5
4.1 Classification. 5
4.2 Designation . 6
5 Information to be supplied by the purchaser . 6
5.1 Mandatory information . 6
5.2 Options . 6
6 Manufacturing process . 6
6.1 Steel making process . 6
6.2 Delivery conditions . 7
7 Requirements . 7
7.1 General. 7
7.2 Chemical composition . 7
7.3 Mechanical properties . 7
7.4 Technological properties . 8
7.5 Surface condition . 9
7.6 Internal soundness . 9
7.7 Dimensions, tolerances on dimensions and shape, mass . 9
7.8 Load Bearing Capacity . 9
8 Inspection . 9
8.1 Type of inspection and inspection document . 9
8.2 Content of inspection document. 9
8.3 Tests to be carried out for specific inspection . 10
9 Frequency of testing and preparation of samples and test pieces . 10
9.1 Test unit . 10
9.2 Frequency of testing . 10
9.3 Preparation of samples and test pieces . 11
9.4 Identification of samples and test pieces . 12
10 Test methods . 12
10.1 Chemical analysis . 12
10.2 Mechanical tests . 12
10.3 Retests . 13
11 Marking, labelling, packaging . 13
12 Complaints . 13
13 Options . 13
Annex A (normative) Location of test samples. 15
Annex B (normative) Calculation of geometrical cross-sectional properties . 16
Annex C (informative) Steel grades and chemical composition according to EN 10025-2,
EN 10149-2 and EN 10149-3 . 17
Bibliography . 20

oSIST prEN 10249-1:2022
prEN 10249-1:2022 (E)
European foreword
This document (prEN 10249-1:2022) has been prepared by Technical Committee CEN/TC 459 "ECISS –
European Committee for Iron and Steel Standardization" , the secretariat of which is held by AFNOR.
This document is currently submitted to the CEN Enquiry.
This document will supersede EN 10249-1:1995.
In comparison with the previous edition, the following technical modifications have been made:
a) Restructuring of the standard;
b) Updating of the normative references;
c) New definitions 3.1 and 3.3;
d) Specification of grades from EN 10149-2 (S355MC, S420MC) and EN 10149-3 (S355NC, S420NC)
suitable for cold forming;
e) Modification concerning the maximum values for the chemical composition;
f) Addition of 7.4.2 for formability and flame straightening, 7.4.3 dedicated for hot-dip zinc-coating and
7.8 for load bearing capacity;
g) New wording for Clauses 8, 9 and 10 for inspection and testing;
h) Addition of Clause 12 on the complaints;
i) Removal of the former Annexes A and B on Euronorms and equivalent designations;
j) Addition of the Annexes A, B and C.
EN 10249 consists of the following parts, under the general title Cold formed steel sheet piles:
— Part 1: Technical delivery conditions
— Part 2: Tolerances on dimensions and shape
A further standard prEN 10376 with the title Cold formed steel sheet piles – General (Characteristics,
evaluation of conformity and marking) is in preparation and can be used together with EN 10249 after
publication.
Through its sub-committee SC 5 “Steels for heat treatment, alloy steels, free-cutting steels and stainless steels” (secretariat:
DIN).
oSIST prEN 10249-1:2022
prEN 10249-1:2022 (E)
1 Scope
This document specifies the requirements for cold formed steel sheet piles produced from hot rolled strip
or sheet with a thickness equal to or greater than 3 mm in respect of its chemical composition, mechanical
properties and conditions of delivery.
The products specified are for general, structural and civil engineering works. The types of steel sheet
piles covered by this document are: Z-shaped, Omega-shaped and trench sheets. The requirements in
respect of tolerances on shape and dimensions are specified in Part 2 of this document.
2 Normative references
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments) applies.
EN 1011-2, Welding – Recommendations for welding of metallic materials – Part 2: Arc welding of ferritic
steels
EN 1993-5, Eurocode 3 - Design of steel structures - Part 5: Piling
EN 10020:2000, Definition and classification of grades of steel
EN 10021:2006, General technical delivery conditions for steel products
EN 10025-2, Hot rolled products of structural steels – Part 2: Technical delivery conditions for non-alloy
structural steels
EN 10027-1, Designation systems for steels - Part 1: Steel names
EN 10027-2, Designation systems for steels - Part 2: Numerical system
EN 10079:2007, Definition of steel products
EN 10149-2, Hot rolled flat products made of high yield strength steels for cold forming - Part 2: Technical
delivery conditions for thermomechanically rolled steels
EN 10149-3, Hot rolled flat products made of high yield strength steels for cold forming - Part 3: Technical
delivery conditions for normalized or normalized rolled steels
EN 10168, Steel products - Inspection documents - List of information and description
EN 10204, Metallic products - Types of inspection documents
EN 10249-2, Cold formed sheet piling of non alloy steels - Part 2: Tolerances on shape and dimensions
CEN/TR 10261, Iron and steel - European standards for the determination of chemical composition
CEN/TR 10347, Guidance for forming of structural steels in processing
EN ISO 148-1, Metallic materials - Charpy pendulum impact test - Part 1: Test method (ISO 148-1)
EN ISO 377, Steel and steel products - Location and preparation of samples and test pieces for mechanical
testing (ISO 377)
oSIST prEN 10249-1:2022
prEN 10249-1:2022 (E)
EN ISO 1461, Hot dip galvanized coatings on fabricated iron and steel articles - Specifications and test
methods (ISO 1461)
EN ISO 6892-1, Metallic materials - Tensile testing - Part 1: Method of testing at room temperature
(ISO 6892-1)
EN ISO 14284, Steel and iron - Sampling and preparation of samples for the determination of chemical
composition (ISO 14284)
EN ISO 14713-2, Zinc coatings - Guidelines and recommendations for the protection against corrosion of
iron and steel in structures - Part 2: Hot dip galvanizing (ISO 14713-2)
3 Terms and definitions
For the purposes of this document, the terms and definitions given in EN 10020:2000, EN 10021:2006,
EN 10079:2007 and the following apply.
ISO and IEC maintain terminological databases for use in standardization at the following addresses:
— IEC Electropedia: available at https://www.electropedia.org/
— ISO Online browsing platform: available at https://www.iso.org/obp
3.1
product range
group of products produced by o
...