EN ISO 7376:2020

SLOVENSKI STANDARD
01-november-2020
Nadomešča:
SIST EN ISO 7376:2010
Anestezijska in dihalna oprema - Laringoskopi za trahealno intubacijo (ISO
7376:2020)
Anaesthetic and respiratory equipment - Laryngoscopes for tracheal intubation (ISO
7376:2020)
Anästhesie- und Beatmungsgeräte - Laryngoskope für Trachealintubation (ISO
7376:2020)
Matériel d'anesthésie et de réanimation respiratoire - Laryngoscopes pour intubation
trachéale (ISO 7376:2020)
Ta slovenski standard je istoveten z: EN ISO 7376:2020
ICS:
11.040.10 Anestezijska, respiratorna in Anaesthetic, respiratory and
reanimacijska oprema reanimation equipment
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EN ISO 7376
EUROPEAN STANDARD
NORME EUROPÉENNE
September 2020
EUROPÄISCHE NORM
ICS 11.040.10 Supersedes EN ISO 7376:2009
English Version
Anaesthetic and respiratory equipment - Laryngoscopes
for tracheal intubation (ISO 7376:2020)
Matériel d'anesthésie et de réanimation respiratoire - Anästhesie- und Beatmungsgeräte - Laryngoskope für
Laryngoscopes pour intubation trachéale (ISO Trachealintubation (ISO 7376:2020)
7376:2020)
This European Standard was approved by CEN on 26 June 2020.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and
United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2020 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 7376:2020 E
worldwide for CEN national Members.

Contents Page
European foreword . 3

European foreword
This document (EN ISO 7376:2020) has been prepared by Technical Committee ISO/TC 121
"Anaesthetic and respiratory equipment" in collaboration with Technical Committee CEN/TC 215
“Respiratory and anaesthetic equipment” the secretariat of which is held by BSI.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by March 2021, and conflicting national standards shall
be withdrawn at the latest by March 2021.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN ISO 7376:2009.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland,
Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Republic of
North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the
United Kingdom.
Endorsement notice
The text of ISO 7376:2020 has been approved by CEN as EN ISO 7376:2020 without any modification.

INTERNATIONAL ISO
STANDARD 7376
Third edition
2020-08
Anaesthetic and respiratory
equipment — Laryngoscopes for
tracheal intubation
Matériel d'anesthésie et de réanimation respiratoire —
Laryngoscopes pour intubation trachéale
Reference number
ISO 7376:2020(E)
©
ISO 2020
ISO 7376:2020(E)
© ISO 2020
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting
on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address
below or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland
ii © ISO 2020 – All rights reserved

ISO 7376:2020(E)
Contents Page
Foreword .iv
Introduction .v
1 *Scope . 1
2 Normative references . 1
3 *Terms and definitions . 1
4 General requirements . 2
5 Materials . 2
6 Design requirements . 2
6.1 General . 2
6.2 *Environmental conditions . 2
7 Performance requirements . 3
7.1 Handles . 3
7.1.1 *Electrical safety . 3
7.1.2 Electrical contact . 3
7.1.3 Dimensions . 3
7.1.4 *Optical output . 5
7.1.5 *Strength . 5
7.2 Laryngoscope blades . 5
7.2.1 Dimensions . 5
7.2.2 *Rigidity . 5
7.2.3 *Strength . 5
7.2.4 *Illumination . 6
7.2.5 Electrical interface. 6
7.3 Hinged combinations . 6
7.4 Single-piece laryngoscopes . 7
8 Cleaning, disinfection and sterilization . 8
9 Information supplied by the manufacturer . 8
9.1 General . 8
9.2 Marking . 8
9.3 Designated size for the intended patient demographic . 8
9.4 Instructions for use . 8
Annex A (informative) Rationale .10
Annex B (normative) Test method for illumination, strength and rigidity .12
Annex C (informative) Common terms for parts of a laryngoscope blade .15
Bibliography .16
ISO 7376:2020(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular, the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www .iso .org/ directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received (see www .iso .org/ patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation of the voluntary nature of standards, the meaning of ISO specific terms and
expressions related to conformity assessment, as well as information about ISO's adherence to the
World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT), see www .iso .org/
iso/ foreword .html.
This document was prepare
...