EN ISO 10426-3:2019

SLOVENSKI STANDARD
01-december-2019
Nadomešča:
SIST EN ISO 10426-3:2005
Industrija za predelavo nafte in zemeljskega plina - Cementi in materiali za
cementiranje vrtin - 3. del: Preskušanje sestave cementov za globokomorske
vrtine (ISO 10426-3:2019)
Petroleum and natural gas industries - Cements and materials for well cementing - Part
3: Testing of deepwater well cement formulations (ISO 10426-3:2019)
Erdöl- und Erdgasindustrie - Zemente und Materialien für die Zementation von
Tiefbohrungen - Teil 3: Prüfung von Unterwasser-Bohrlochzement (ISO 10426-3:2019)
Industries du pétrole et du gaz naturel - Ciments et matériaux pour la cimentation des
puits - Partie 3: Essais de formulations de ciment pour puits en eau profonde (ISO 10426
-3:2019)
Ta slovenski standard je istoveten z: EN ISO 10426-3:2019
ICS:
75.180.10 Oprema za raziskovanje, Exploratory, drilling and
vrtanje in odkopavanje extraction equipment
91.100.10 Cement. Mavec. Apno. Malta Cement. Gypsum. Lime.
Mortar
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EN ISO 10426-3
EUROPEAN STANDARD
NORME EUROPÉENNE
October 2019
EUROPÄISCHE NORM
ICS 75.020; 91.100.10 Supersedes EN ISO 10426-3:2004
English Version
Petroleum and natural gas industries - Cements and
materials for well cementing - Part 3: Testing of deepwater
well cement formulations (ISO 10426-3:2019)
Industries du pétrole et du gaz naturel - Ciments et Erdöl- und Erdgasindustrie - Zemente und Materialien
matériaux pour la cimentation des puits - Partie 3: für die Zementation von Tiefbohrungen - Teil 3:
Essais de formulations de ciment pour puits en eau Prüfung von Unterwasser-Bohrlochzement (ISO
profonde (ISO 10426-3:2019) 10426-3:2019)
This European Standard was approved by CEN on 9 June 2019.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and
United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2019 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 10426-3:2019 E
worldwide for CEN national Members.

Contents Page
European foreword . 3

European foreword
This document (EN ISO 10426-3:2019) has been prepared by Technical Committee ISO/TC 67
"Materials, equipment and offshore structures for petroleum, petrochemical and natural gas industries"
in collaboration with Technical Committee CEN/TC 12 “Materials, equipment and offshore structures
for petroleum, petrochemical and natural gas industries” the secretariat of which is held by NEN.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by April 2020, and conflicting national standards shall be
withdrawn at the latest by April 2020.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN ISO 10426-3:2004.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland,
Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Republic of
North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the
United Kingdom.
Endorsement notice
The text of ISO 10426-3:2019 has been approved by CEN as EN ISO 10426-3:2019 without any
modification.
INTERNATIONAL ISO
STANDARD 10426-3
Second edition
2019-08
Petroleum and natural gas
industries — Cements and materials
for well cementing —
Part 3:
Testing of deepwater well cement
formulations
Industries du pétrole et du gaz naturel — Ciments et matériaux pour
la cimentation des puits —
Partie 3: Essais de formulations de ciment pour puits en eau profonde
Reference number
ISO 10426-3:2019(E)
©
ISO 2019
ISO 10426-3:2019(E)
© ISO 2019
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting
on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address
below or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Fax: +41 22 749 09 47
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland
ii © ISO 2019 – All rights reserved

ISO 10426-3:2019(E)
Contents Page
Foreword .iv
Introduction .vi
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
nd
4 Supplements to API RP 10B-3, 2 edition (2016) . 2
4.1 General requirements . 2
4.2 Procedure for compressive strength determination . 2
4.3 Thickening-time schedule determination . 2
4.3.1 Testing method and procedures for a casing or liner without a liner-top
packer or non-expandable liner hanger system . 2
4.3.2 Testing method for a liner with a liner-top packer or expandable liner
hanger system . 2
4.3.3 Testing method for open-hole or closed-hole plug . 2
4.3.4 Thickening-time test procedure . 2
4.3.5 Testing method for continuous-pumping squeeze cementing . 3
4.3.6 Testing method for hesitating-pumping squeeze cementing . 3
Bibliography . 4
ISO 10426-3:2019(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular, the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www .iso .org/directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received (see www .iso .org/patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation of the voluntary nature of standards, the meaning of ISO specific terms and
expressions related to conformity assessment, as well as information about ISO's adherence to the
World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT) see www .iso
.org/iso/foreword .html.
This document was prepared by Technical Committee ISO/TC 67, Materials, equipment and offshore
structures for petroleum, petrochemical and natural gas industries, Subcommittee SC 3, Drilling and
completion fluids, and well cements.
This second edition cancels and replaces the first edition (ISO 10426-3:2003), which has been
technically revised.
nd
This document supplements API RP 10B-3, 2 edition (2016).
The technical requirements of this document and API RP 10B-3 used to be identical. In the meantime,
nd
API RP 10B-3 has been technically revised as API RP 10B-3, 2 edition (2016). The purpose of this
document is to bring this document up-to-date, by referencing the current edition of API RP 10B-3 and
adding supplementary content.
The main changes compared to the previous edition are as follows:
— A clause on numerical pressure and temperature simulation has been added in order to allow
accurate determination of the pressure and temperature schedules required for the various tests;
— Strength determination at the casing shoe, the mudline, potential flow zones, top-of-liner and open-
or cased hole plug and squeeze locations is treated separately;
— Directions for sonic strength testing data reporting have been included;
— The laboratory procedures for both sonic and destructive strength measurements have been
expanded;
— A clause has been added on thickening time simulations for liner cementations with and without the
use of either liner-top packers or expandable liner hangers.
A list of all parts in the ISO 10426 series can be found on the ISO website.
iv © ISO 2019 – All rights reserved

ISO 10426-3:2019(E)
Any feedback or questions on this document should be directed to the user’s national standards body. A
complete listing of these bodies can be found at www .iso .org/members .html.
ISO 10426-3:2019(E)
Introduction
The test methods contained in this document, though generally based on ISO 10426-2, consider the
specialized sampling/testing requirements and unique downhole temperature profiles found in
deepwater wells. ISO 10426-2 contains no applicable well simulation schedules for deepwater cementing
operations.
In a deepwater cementing environment, several factors impact the thermal history of the cement
slurry. These factors include: water depth, mud-line temperature, geothermal gradient, the presence or
absence of a drilling riser, drilling fluid temperature, ocean current velocity, presence of thermoclines
(layers of ocean water separated by temperature), ambient sea-surface temperature, cement mix-water
temperature, bulk cement temperature, cement mixing rate, cement heat of hydration, displacement rate,
prior circulating and static event history, drill pipe size and mass, casing size and mass, and hole
...