EN ISO 15876-2:2003/A1:2007

SLOVENSKI STANDARD
01-december-2007
&HYQLVLVWHPLL]SROLPHUQLKPDWHULDORY]DQDSHOMDYH]YURþRLQKODGQRYRGR
3ROLEXWLOHQ3%GHO&HYL'RSROQLOR,62$PG
Plastics piping systems for hot and cold water installations - Polybutylene (PB) - Part 2:
Pipes - Amendment 1 (ISO 15876-2:2003/Amd 1:2007)
Kunststoff-Rohrleitungssysteme für die Warm- und Kaltwasserinstallation - Polybuten
(PB) - Teil 2: Rohre - Änderung 1 (ISO 15876-2:2003/Amd 1:2007)
Systemes de canalisations en plastique pour les installations d'eau chaude et froide -
Polybutene (PB) - Partie 2: Tubes - Amendement 1 (ISO 15876-2:2003/Amd 1:2007)
Ta slovenski standard je istoveten z: EN ISO 15876-2:2003/A1:2007
ICS:
23.040.20 Cevi iz polimernih materialov Plastics pipes
91.140.60 Sistemi za oskrbo z vodo Water supply systems
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EUROPEAN STANDARD
EN ISO 15876-2:2003/A1
NORME EUROPÉENNE
EUROPÄISCHE NORM
June 2007
ICS 91.140.60; 23.040.20
English Version
Plastics piping systems for hot and cold water installations -
Polybutylene (PB) - Part 2: Pipes - Amendment 1 (ISO 15876-
2:2003/Amd 1:2007)
Systèmes de canalisations en plastique pour les Kunststoff-Rohrleitungssysteme für die Warm- und
installations d'eau chaude et froide - Polybutène (PB) - Kaltwasserinstallation - Polybuten (PB) - Teil 2: Rohre -
Partie 2: Tubes - Amendement 1 (ISO 15876-2:2003/Amd Änderung 1 (ISO 15876-2:2003/Amd 1:2007)
1:2007)
This amendment A1 modifies the European Standard EN ISO 15876-2:2003; it was approved by CEN on 9 June 2007.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for inclusion of this
amendment into the relevant national standard without any alteration. Up-to-date lists and bibliographical references concerning such
national standards may be obtained on application to the CEN Management Centre or to any CEN member.
This amendment exists in three official versions (English, French, German). A version in any other language made by translation under the
responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as the official
versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland,
France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,
Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: rue de Stassart, 36  B-1050 Brussels
© 2007 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 15876-2:2003/A1:2007: E
worldwide for CEN national Members.

Foreword
This document (EN ISO 15876-2:2003/A1:2007) has been prepared by Technical Committee
CEN/TC 155 "Plastics piping systems and ducting systems", the secretariat of which is held by
NEN, in collaboration with Technical Committee ISO/TC 138 "Plastics pipes, fittings and valves
for the transport of fluids".
This European Standard shall be given the status of a national standard, either by publication of
an identical text or by endorsement, at the latest by December 2007, and conflicting national
standards shall be withdrawn at the latest by December 2007.

According to the CEN/CENELEC Internal Regulations, the national standards organizations of
the following countries are bound to implement this European Standard: Austria, Belgium,
Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece,
Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United
Kingdom.
INTERNATIONAL ISO
STANDARD 15876-2
First edition
2003-12-01
AMENDMENT 1
2007-06-15
Plastics piping systems for hot and cold
water installations — Polybutylene
(PB) —
Part 2:
Pipes
AMENDMENT 1
Systèmes de canalisations en plastique pour les installations d'eau
chaude et froide — Polybutène (PB) —
Partie 2: Tubes
AMENDEMENT 1
Reference number
ISO 15876-2:2003/Amd.1:2007(E)
©
ISO 2007
ISO 15876-2:2003/Amd.1:2007(E)
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but
shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In
downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat
accepts no liability in this area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation
parameters were optimized for printing. Every care has been taken to ensure that th
...