EN ISO 9015-2:2011

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Porušitveni preskusi zvarov na kovinskih materialih - Preskušanje trdote - 2. del: Preskušanje mikrotrdote zvarnih spojev (ISO 9015-2:2003)Zerstörende Prüfung von Schweißverbindungen an metallischen Werkstoffen - Härteprüfung - Teil 2: Mikrohärteprüfung an Schweißverbindungen (ISO 9015-2:2003)Essais destructifs des soudures sur matériaux métalliques - Essais de dureté - Partie 2: Essai de microdureté des assemblages soudés (ISO 9015-2:2003)Destructive tests on welds in metallic materials - Hardness testing - Part 2: Microhardness testing of welded joints (ISO 9015-2:2003)25.160.40Varjeni spoji in variWelded jointsICS:Ta slovenski standard je istoveten z:EN ISO 9015-2:2011SIST EN ISO 9015-2:2012en,fr,de01-januar-2012SIST EN ISO 9015-2:2012SLOVENSKI
STANDARDSIST EN 1043-2:19981DGRPHãþD

EUROPEAN STANDARD NORME EUROPÉENNE EUROPÄISCHE NORM
EN ISO 9015-2
March 2011 ICS 25.160.40 Supersedes EN 1043-2:1996English Version
Destructive tests on welds in metallic materials - Hardness testing - Part 2: Microhardness testing of welded joints (ISO 9015-2:2003)
Essais destructifs des soudures sur matériaux métalliques -Essais de dureté - Partie 2: Essai de microdureté des assemblages soudés (ISO 9015-2:2003)
Zerstörende Prüfung von Schweißverbindungen an metallischen Werkstoffen - Härteprüfung - Teil 2: Mikrohärteprüfung an Schweißverbindungen (ISO 9015-2:2003) This European Standard was approved by CEN on 13 February 2011.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre:
Avenue Marnix 17,
B-1000 Brussels © 2011 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN ISO 9015-2:2011: ESIST EN ISO 9015-2:2012

Reference numberISO 9015-2:2003(E)© ISO 2003
INTERNATIONAL STANDARD ISO9015-2First edition2003-11-15Destructive tests on welds in metallic materials — Hardness testing — Part 2: Microhardness testing of welded joints Essais destructifs des soudures sur matériaux métalliques —Essais de dureté — Partie 2: Essai de microdureté des assemblages soudés
ISO 9015-2:2003(E) PDF disclaimer This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat accepts no liability in this area. Adobe is a trademark of Adobe Systems Incorporated. Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.
©
ISO 2003 All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or ISO's member body in the country of the requester. ISO copyright office Case postale 56 • CH-1211 Geneva 20 Tel.
+ 41 22 749 01 11 Fax
+ 41 22 749 09 47 E-mail
copyright@iso.org Web
www.iso.org Published in Switzerland
ii © ISO 2003 — All rights reserved
ISO 9015-2:2003(E) © ISO 2003 — All rights reserved iii Contents Page Foreword.iv 1 Scope.1 2 Normative references.1 3 Principle.1 4 Symbols and abbreviated terms.2 5 Preparation of test specimens.2 6 Test procedure.2 6.1 Rows of indentations (R).2 6.2 Individual indentations (E).3 7 Test results.3 8 Test report.3 Annex A (informative)
Example of a test report for rows of hardness tests (R) on welded joints.7 Annex B (informative)
Example of a test report for individual hardness tests (E) on welded joints.8 Bibliography.9
ISO 9015-2:2003(E) iv © ISO 2003 — All rights reserved Foreword ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2. The main task of technical committees is to prepare International Standards. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. ISO 9015-2 was prepared by Technical Committee ISO/TC 44, Welding and allied processes, Subcommittee SC 5, Testing and inspection of welds. ISO 9015 consists of the following parts, under the general title Destructive tests on welds in metallic materials — Hardness testing:  Part 1: Hardness test on arc welded joints  Part 2: Microhardness testing of welded joints
INTERNATIONAL STANDARD ISO 9015-2:2003(E) © ISO 2003 — All rights reserved 1 Destructive tests on welds in metallic materials — Hardness testing — Part 2: Microhardness t
...