EN 1007-4:2004
(Main)Advanced technical ceramics - Ceramic composites - Methods of test for reinforcement - Part 4: Determination of tensile properties of filaments at ambient temperature
Advanced technical ceramics - Ceramic composites - Methods of test for reinforcement - Part 4: Determination of tensile properties of filaments at ambient temperature
This part of EN 1007 specifies the conditions for determination of tensile strength and elongation at fracture of single filaments of ceramic fibre such as tensile strength, Young modulus and stress-strain curve. The method applies to continuous ceramic filaments taken from tows, yarns, braids and knittings, which have strain to fracture less than or equal to 5 %.
The method does not apply to check the homogeneity of strength properties of fibres, nor to assess the effects of volume under stress. Statistical aspects of filament failure are not included.
Hochleistungskeramik - Keramische Verbundwerkstoffe - Verfahren zur Prüfung der Faserverstärkungen - Teil 4: Bestimmung der Zugeigenschaften von Fasern bei Raumtemperatur
Dieser Teil der prEN 1007 legt die Bedingungen zur Messung der Zugfestigkeit und der Auslenkung beim Bruch von einzelnen Abschnitten keramischer Fasern fest. Das Prüfverfahren liefert das Verfahren zur Bestimmung der Zugfestigkeit und Anhang B zur Bestimmung des elastischen Moduls. Das Verfahren bezieht sich auf eine kontinuierliche keramische Fasern, die aus Tauen, Garnen, Stapel, Fasern und Zwirnen entnommen werden und die weniger als 5% Bruchdehnung haben und die linear-elastisches Verhalten zum Bruch zeigen.
Céramiques techniques avancées - Composites céramiques - Méthodes d'essai pour renforts - Partie 4: Détermination des propriétés en traction du filament à température ambiante
La présente partie de l'EN 1007 spécifie les conditions de détermination de la résistance en traction et de l'allongement à la rupture d'un filament de fibre céramique, à savoir de la résistance en traction, du module de Young et de la courbe contrainte-déformation. La méthode s'applique à des filaments céramiques continus issus de mèches, fils, tresses et tricots ayant des allongements à la rupture ou égaux à 5 %.
La méthode ne permet pas de soumettre à essai l'homogénéité des propriétés de traction des fibres, elle ne permet pas plus d'évaluer les effets de volume sous contrainte. L'aspect statistique de la rupture des fibres n'est pas envisagé.
Sodobna tehnična keramika – Keramični kompoziti – Preskusne metode za ojačitve – 4. del: Ugotavljanje nateznih lastnosti vlaken pri sobni temperaturi
General Information
- Status
- Withdrawn
- Publication Date
- 18-May-2004
- Withdrawal Date
- 20-Jan-2026
- Technical Committee
- CEN/TC 184 - Advanced technical ceramics
- Drafting Committee
- CEN/TC 184/SC 1 - Ceramic composites
- Current Stage
- 9960 - Withdrawal effective - Withdrawal
- Start Date
- 21-Jul-2021
- Completion Date
- 21-Jan-2026
Relations
- Effective Date
- 22-Dec-2008
- Effective Date
- 08-Jun-2022
- Effective Date
- 08-Jun-2022
Frequently Asked Questions
EN 1007-4:2004 is a standard published by the European Committee for Standardization (CEN). Its full title is "Advanced technical ceramics - Ceramic composites - Methods of test for reinforcement - Part 4: Determination of tensile properties of filaments at ambient temperature". This standard covers: This part of EN 1007 specifies the conditions for determination of tensile strength and elongation at fracture of single filaments of ceramic fibre such as tensile strength, Young modulus and stress-strain curve. The method applies to continuous ceramic filaments taken from tows, yarns, braids and knittings, which have strain to fracture less than or equal to 5 %. The method does not apply to check the homogeneity of strength properties of fibres, nor to assess the effects of volume under stress. Statistical aspects of filament failure are not included.
This part of EN 1007 specifies the conditions for determination of tensile strength and elongation at fracture of single filaments of ceramic fibre such as tensile strength, Young modulus and stress-strain curve. The method applies to continuous ceramic filaments taken from tows, yarns, braids and knittings, which have strain to fracture less than or equal to 5 %. The method does not apply to check the homogeneity of strength properties of fibres, nor to assess the effects of volume under stress. Statistical aspects of filament failure are not included.
EN 1007-4:2004 is classified under the following ICS (International Classification for Standards) categories: 81.060.30 - Advanced ceramics. The ICS classification helps identify the subject area and facilitates finding related standards.
EN 1007-4:2004 has the following relationships with other standards: It is inter standard links to ENV 1007-4:1994, EN ISO 19630:2021, EN 1007-4:2004/AC:2007. Understanding these relationships helps ensure you are using the most current and applicable version of the standard.
EN 1007-4:2004 is associated with the following European legislation: Standardization Mandates: M/BC/CEN/90/4. When a standard is cited in the Official Journal of the European Union, products manufactured in conformity with it benefit from a presumption of conformity with the essential requirements of the corresponding EU directive or regulation.
EN 1007-4:2004 is available in PDF format for immediate download after purchase. The document can be added to your cart and obtained through the secure checkout process. Digital delivery ensures instant access to the complete standard document.
Standards Content (Sample)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Hochleistungskeramik - Keramische Verbundwerkstoffe - Verfahren zur Prüfung der Faserverstärkungen - Teil 4: Bestimmung der Zugeigenschaften von Fasern bei RaumtemperaturCéramiques techniques avancées - Composites céramiques - Méthodes d'essai pour renforts - Partie 4: Détermination des propriétés en traction du filament a température ambianteAdvanced technical ceramics - Ceramic composites - Methods of test for reinforcement - Part 4: Determination of tensil
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.
Loading comments...