EN 88-1:2022+A1:2023
(Main + Amendment)Safety and control devices for gas burners and gas burning appliances - Part 1: Pressure regulators for inlet pressures up to and including 50 kPa
Safety and control devices for gas burners and gas burning appliances - Part 1: Pressure regulators for inlet pressures up to and including 50 kPa
EN 13611:2019, Clause 1 applies with the following modification and addition:
Modification:
The 1st paragraph of EN 13611:2019, Clause 1 is replaced by:
This document specifies the safety, design, construction, and performance requirements and testing for
pressure regulators and pneumatic gas/air ratio pressure regulators (zero pressure regulators are
included as a special type of pneumatic gas/air ratio pressure regulators) for burners and appliances
burning one or more gaseous fuels, hereafter referred to as “pressure regulators”.
This document is applicable to pressure regulators with declared maximum inlet pressures up to and
including 50 kPa and of nominal connection sizes up to and including DN 250.
Addition:
This document is applicable to:
— pressure regulators which use auxiliary energy;
— pneumatic gas/air ratio pressure regulators, which function by controlling a gas outlet pressure in
response to an air signal pressure, air signal differential pressure, and/or to a furnace pressure signal
(zero pressure regulators are included as a special type of pneumatic gas/air ratio pressure
regulators);
— pneumatic gas/air ratio pressure regulators, which change an air outlet pressure in response to a gas
signal pressure or a gas signal differential pressure.
This document is not applicable to:
— pressure regulators connected directly to a gas distribution network or to a container that maintains
a standard distribution pressure;
— pressure regulators intended for gas appliances to be installed in the open air and exposed to the
environment;
— mechanically linked gas/air ratio controls;
— electronic gas/air ratio controls (EN 12067-2:2022).
The 4th paragraph of EN 13611:2019, Clause 1 is removed.
Sicherheits- und Regeleinrichtungen für Gasbrenner und Gasgeräte - Teil 1: Druckregler für Eingangsdrücke bis einschließlich 50 kPa
EN 13611:2019, Abschnitt 1, gilt mit folgender Änderung und Ergänzung:
Änderung:
Der erste Absatz von EN 13611:2019, Abschnitt 1, wird ersetzt durch:
Dieses Dokument legt die Sicherheits-, Auslegungs-, Konstruktions- und Leistungsanforderungen sowie die Prüfung von Druckreglern und pneumatischen Gas-Luft-Verbundreglern (Nulldruckregler sind als besonderer Typ von pneumatischen Gas-Luft-Verbundreglern eingeschlossen) für Brenner und Brennstoffgeräte für einen oder mehrere gasförmige Brennstoffe, nachstehend als „Druckregler“ bezeichnet, fest.
Dieses Dokument gilt für Druckregler mit einem angegebenen höchsten Eingangsdruck bis einschließlich 50 kPa und mit Anschlussnennweiten bis einschließlich DN 250.
Ergänzung:
Dieses Dokument gilt für:
- Druckregler, die elektrische Hilfsenergie verwenden;
- pneumatische Gas-Luft-Verbundregler (Nulldruckregler sind als besonderer Typ von pneumatischen Gas-Luft-Verbundreglern eingeschlossen), die einen Gasausgangsdruck in Abhängigkeit von einem Luftsignal¬druck, einem Luftsignal-Differenzdruck und/oder einem Feuerraumdrucksignal regeln;
- pneumatische Gas-Luft-Verbundregler, die eine Änderung des Luftausgangsdrucks in Abhängigkeit von einem Gassignaldruck oder einem Gassignal-Differenzdruck regeln.
Dieses Dokument gilt nicht für:
- Druckregler, die unmittelbar an ein Gasverteilungsnetz oder an einen Behälter mit genormtem Verteilungsdruck angeschlossen sind;
- Druckregler für Gasgeräte in Freiluftausführung, die Umwelteinflüssen ausgesetzt sind;
- mechanisch verbundene Gas-Luft-Verbundregler;
- elektronische Gas-Luft-Verbundregler (EN 12067 2:2022).
Der vierte Absatz von EN 13611:2019, Abschnitt 1, entfällt.
Dispositifs de sécurité et de contrôle pour les brûleurs à gaz et appareils utilisant des combustibles gazeux - Partie 1 : Régulateurs de pression pour pression amont inférieure ou égale à 50 kPa
Varnostne in nadzorne naprave za plinske gorilnike in plinske aparate - 1. del: Regulatorji tlaka za vstopne tlake do vključno 50 kPa (vključno z dopolnilom A1)
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
01-oktober-2024
Nadomešča:
SIST EN 88-1:2022
Varnostne in nadzorne naprave za plinske gorilnike in plinske aparate - 1. del:
Regulatorji tlaka za vstopne tlake do vključno 50 kPa (vključno z dopolnilom A1)
Safety and control devices for gas burners and gas burning appliances - Part 1: Pressure
regulators for inlet pressures up to and including 50 kPa
Sicherheits- und Regeleinrichtungen für Gasbrenner und Gasgeräte - Teil 1: Druckregler
für Eingangsdrücke bis einschließlich 50 kPa
Dispositifs de sécurité et de contrôle pour les brûleurs à gaz et appareils utilisant des
combustibles gazeux - Partie 1 : Régulateurs de pression pour pression amont inférieure
ou égale à 50 kPa
Ta slovenski standard je istoveten z: EN 88-1:2022+A1:2023
ICS:
23.060.40 Tlačni regulatorji Pressure regulators
27.060.20 Plinski gorilniki Gas fuel burners
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
EN 88-1:2022+A1
EUROPEAN STANDARD
NORME EUROPÉENNE
December 2023
EUROPÄISCHE NORM
ICS 23.060.40 Supersedes EN 88-1:2022
English Version
Safety and control devices for gas burners and gas burning
appliances - Part 1: Pressure regulators for inlet pressures
up to and including 50 kPa
Dispositifs de sécurité et de contrôle pour les brûleurs Sicherheits- und Regeleinrichtungen für Gasbrenner
à gaz et appareils utilisant des combustibles gazeux - und Gasgeräte - Teil 1: Druckregler für Eingangsdrücke
Partie 1 : Régulateurs de pression pour pression amont bis einschließlich 50 kPa
inférieure ou égale à 50 kPa
This European Standard was approved by CEN on 8 August 2022 and includes Amendment approved by CEN on 11 October
2023.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Türkiye and
United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2023 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 88-1:2022+A1:2023 E
worldwide for CEN national Members.
Contents Page
European foreword . 5
Introduction . 6
1 Scope . 8
2 Normative references . 9
3 Terms and definitions . 9
4 Classification . 13
4.1 Classes of control . 13
4.2 Groups of control . 13
4.3 Classes of control functions . 14
4.4 Types of DC supplied controls . 14
5 Test conditions and uncertainty of measurements . 14
6 Design and construction . 14
6.1 General . 14
6.2 Mechanical parts of the control . 14
6.2.1 Appearance . 14
6.2.2 Holes . 14
6.2.3 Breather holes . 14
6.2.4 Screwed fastenings . 15
6.2.5 Jointing . 15
6.2.6 Moving parts . 15
6.2.7 Sealing caps. 15
6.2.8 Dismantling and reassembly . 15
6.2.9 Auxiliary canals and orifices . 15
6.2.10 Presetting device . 15
6.2.101 Adjustments . 15
6.2.102 Resistance to pressure . 15
6.2.103 Signal tube connections. 15
6.3 Materials . 16
6.3.1 General material requirements . 16
6.3.2 Housing . 16
6.3.3 Zinc alloys . 16
6.3.4 Springs . 16
6.3.5 Resistance to corrosion and surface protection . 16
6.3.6 Impregnation . 16
6.3.7 Seals for glands for moving parts . 16
6.4 Gas connections . 16
6.5 Electrical parts of the control . 16
6.5.1 General . 16
6.5.2 Switching elements . 16
6.5.3 Electrical components . 16
6.6 Protection against internal faults for the purpose of functional safety . 16
7 Performance . 17
7.1 General . 17
7.2 Leak-tightness . 17
7.2.1 Requirements . 17
7.2.2 Tests . 17
7.2.101 External leak-tightness for gas signal carrying compartment(s) . 17
7.2.102 External leak-tightness for air signal carrying compartment(s) . 17
7.3 Torsion and bending . 17
7.4 Rated flow rate . 17
7.4.1 Requirements . 17
7.4.2 Test . 17
7.4.3 Conversion of air flow rate . 18
7.5 Durability . 18
7.6 Performance tests for electronic controls . 18
7.7 Long-term performance for electronic controls . 18
7.8 Data exchange . 18
7.101 Pressure regulator performance . 18
7.101.1 General . 18
7.101.2 General test procedure . 19
7.101.3 Class A pressure regulator performance . 21
7.101.4 Class B pressure regulator performance . 22
7.101.5 Class C pressure regulator performance . 22
7.101.6 Endurance . 23
7.101.7 Lock-up pressure . 24
7.101.8 Rendered inoperative pressure regulators . 24
7.102 Pneumatic gas/air ratio pressure regulator performance . 25
7.102.1 General . 25
7.102.2 General test procedure . 25
7.102.3 Control performance and stability . 25
7.102.4 Settling time . 28
7.102.5 Gas/air ratio adjustment .
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.