EN 15814:2011+A1:2012

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Bitumenske debeloslojne prevleke, modificirane s polimeri - Definicije in zahteveKunststoffmodifizierte Bitumendickbeschichtungen zur Bauwerksabdichtung - Begriffe und AnforderungenRevêtements bitumineux épais modifiés aux polymères pour imperméabilisation - Définitions et exigencesPolymer modified bituminous thick coatings for waterproofing - Definitions and requirements91.100.50Veziva. Tesnilni materialiBinders. Sealing materialsICS:Ta slovenski standard je istoveten z:EN 15814:2011+A1:2012SIST EN 15814:2011+A1:2012en,fr,de01-december-2012SIST EN 15814:2011+A1:2012SLOVENSKI
STANDARD
EUROPEAN STANDARD NORME EUROPÉENNE EUROPÄISCHE NORM
EN 15814:2011+A1
October 2012 ICS 91.100.50 Supersedes EN 15814:2011English Version
Polymer modified bituminous thick coatings for waterproofing - Definitions and requirements
Revêtements bitumineux épais modifiés aux polymères pour imperméabilisation - Définitions et exigences
Kunststoffmodifizierte Bitumendickbeschichtungen zur Bauwerksabdichtung - Begriffe und Anforderungen This European Standard was approved by CEN on 14 July 2011 and includes Amendment 1 approved by CEN on 20 August 2012.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre:
Avenue Marnix 17,
B-1000 Brussels © 2012 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 15814:2011+A1:2012: ESIST EN 15814:2011+A1:2012

Reaction to fire — Specifications for mounting specimens in the test rigs . 15Annex ZA (informative)
!!!!Clauses of this European Standard addressing the provisions of the EU Construction Products Directive"""" . 16 SIST EN 15814:2011+A1:2012

bituminous thick coatings for waterproofing — Resistance to compression EN 15816, Polymer modified bituminous thick coatings for waterproofing — Resistance to rain EN 15817, Polymer modified bituminous thick coatings for waterproofing — Water resistance EN 15818, Polymer modified bituminous thick coatings for water proofing — Determination of dimensional stability at high temperature EN 15819, Polymer modified bituminous thick coatings for waterproofing — Reduction of the thickness of the layer when fully dried
EN 15820, Polymer modified bituminous thick coatings for waterproofing — Determination of watertightness ISO 1183-1: 2004, Plastics - Methods for determining the density of non-cellular plastics - Part_1: Immersion method, liquid pyknometer method and titration method EN ISO 2811-1:2011, Paints and varnishes — Determination of density — Part 1: Pyknometer method (ISO 2811-1:1997) EN ISO 2811-2, Paints and varnishes — Determination of density — Part 2: Immersed body (plummet) method (ISO 2811-2:1997) SIST EN 15814:2011+A1:2012

EN ISO 3451-1, Plastics — Determination of ash — Part 1: General methods (ISO 3451-1:2008) EN ISO 3923-1, Metallic powders — Determination of apparent density — Part 1: Funnel method (ISO 3923-1:2008) EN ISO 11925-2, Reaction to fire tests — Ignitability of products subjected to direct impingement of flame — Part 2: Single-flame source test (ISO/FDIS 11925-2:2010) 3 Terms and definitions For the purposes of this document, the following terms and definitions apply. 3.1 crack bridging ability ability of a product to bridge a crack that originates below ground under specified conditions and without damage 3.2 free film cured polymer modified bituminous coating emulsion based, which is tested without being applied to a substrate 3.3 inlay industrially produced material, which is incorporated as an intermediate layer when applying the coating
3.4 PMBC !Polymer Modified Bituminous thick Coating emulsion based, with or without admixtures, such as additives and mineral aggregates, comprising of one or two components" 3.5 pressure water water in ground with hydrostatic pressure
Crack width ≥ 1 mm dry layer thickness
≥ 3 mm (MLV) Class CB 2 No damage
Crack width ≥ 2 mm dry layer thickness
≥ 3 mm (MLV) EN 15812 Method A or BNOTE The test method has to be declared with the classification.
2 Resistance to rain Class R0 No require-ment
Class R1 ≤ 24 h
wet layer thickness ≥ 3 mm (MLV) Class R2
≤ 8 h
wet layer thickness ≥ 3 mm (MLV) Class R3 ≤ 4 h
wet layer
thickness ≥ 3 mm (MLV) EN 15816 3 Water resistance 1.No colouration of the water 2.No debonding from inlay, if used dry layer ≥ 4 mm No changes to the material according to EN 15817,
EN 15817 4 Flexibility at low temperature !deleted text" No cracks
EN 15813 5 Dimensional stability at high temperature !deleted text" No sliding or draining down
EN 15818 SIST EN 15814:2011+A1:2012

Testing in accordance with the specifications in the classification standard EN 13501-1and Annex A.
8 Watertightness a Class W1 ≥ 24 h at 0,0075 N/mm2dry layer
thickness without inlay ≥ 3 mm (MLV) Class W2A ≥ 72 h at 0,075 N/mm2 dry layer thickness with inlay ≥ 4 mm with inlay (MLV) Class W2B ≥ 72 h at
0,075 N/mm2 dry layer thickness without inlay ≥ 4 mm without inlay (MLV) EN 15820 9 Resistance to compression a Class C0 No requirement Class C1 Stabilization at ≤ 50 % (change maximum 3 % within 3 subse-quent days) 0,06 MN/m2dry layer thickness
≥ 3 mm (MLV) Class C2A Stabilization at ≤ 50 % (change maximum 3 % within 3 subse-quent days) 0,30 MN/m2dry layer thickness
≥ 4 mm with inlay (MLV) Class C2B Stabilization at ≤ 50 % (change maximum 3 % within 3 subse-quent days) 0,30 MN/m2 dry layer thickness
≥ 4 mm without inlay (MLV) EN 15815 !a The testing procedure of characteristics are also related to durability aspects." manufacturer's limiting value (MLV) value stated by the manufacturer to be met during testing. The manufacturer's limiting value can be a minimum or a maximum value according to statements made under product characteristics of this document
When required, the water vapour diffusion resistance shall be tested in accordance with EN 1931. SIST EN 15814:2011+A1:2012
...