FprEN ISO 19932-3
(Main)Equipment for crop protection - Knapsack sprayers - Part 3: Inspection of knapsack sprayers in use (ISO/FDIS 19932-3:2019)
Equipment for crop protection - Knapsack sprayers - Part 3: Inspection of knapsack sprayers in use (ISO/FDIS 19932-3:2019)
This Standard specifies the requirements and test methods for the inspection in use of Knapsack sprayers of over 3 litres nominal volume carried on the back or shoulder of the operator for applying Plant Protection Products (PPPs) in agriculture and horticulture.
It is applicable to lever-operated knapsack sprayers, knapsack compression sprayers and knapsack sprayers driven by an engine or electric motor using hydraulic energy to atomise the spray liquid.
The requirements relate mainly to the condition of the sprayer with respect to its potential risk to the operator and the environment and its performance to achieve good application.
It does not apply to other portable equipment such as knapsack combustion engine-driven air blast sprayers/mistblowers (see ISO 10988 and ISO 28139), Controlled Droplet Application equipment utilising rotary atomisers, or portable application equipment for spatial application (e.g. foggers).
Pflanzenschutzgeräte - Tragbare Geräte - Teil 3: Kontrolle von in Gebrauch befindlichen Geräten (ISO/FDIS 19932-3:2019)
Matériel de protection des cultures - Pulvérisateurs à dos - Partie 3: Contrôle des pulvérisateurs portables à dos en service (ISO/FDIS 19932-3:2019)
Oprema za zaščito poljščin - Nahrbtni škropilniki - 3. del: Preverjanje delovanja nahrbtnih škropilnikov (ISO/FDIS 19932-3:2019)
General Information
Standards Content (Sample)
SLOVENSKI STANDARD
oSIST prEN ISO 19932-3:2017
01-junij-2017
2SUHPD]D]DãþLWRSROMãþLQ1DKUEWQLãNURSLOQLNLGHO3UHYHUMDQMHGHORYDQMD
QDKUEWQLKãNURSLOQLNRY,62',6
Equipment for crop protection - Knapsack sprayers - Part 3: Inspection of knapsack
sprayers in use (ISO/DIS 19932-3:2017)
Pflanzenschutzgeräte - Tragbare Geräte - Teil 3: Kontrolle von in Gebrauch befindlichen
Geräten (ISO/DIS 19932-3:2017)
Matériel de protection des cultures - Pulvérisateurs à dos - Partie 3: Contrôle des
pulvérisateurs portables à dos en service (ISO/DIS 19932-3:2017)
Ta slovenski standard je istoveten z: prEN ISO 19932-3
ICS:
65.060.40 Oprema za nego rastlin Plant care equipment
oSIST prEN ISO 19932-3:2017 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
oSIST prEN ISO 19932-3:2017
oSIST prEN ISO 19932-3:2017
DRAFT INTERNATIONAL STANDARD
ISO/DIS 19932-3
ISO/TC 23/SC 6 Secretariat: AFNOR
Voting begins on: Voting terminates on:
2017-03-30 2017-06-21
Equipment for crop protection — Knapsack sprayers —
Part 3:
Inspection of knapsack sprayers in use
Matériel de protection des cultures — Pulvérisateurs à dos —
Partie 3: Contrôle des pulvérisateurs portables à dos en service
ICS: 65.060.40
THIS DOCUMENT IS A DRAFT CIRCULATED
This document is circulated as received from the committee secretariat.
FOR COMMENT AND APPROVAL. IT IS
THEREFORE SUBJECT TO CHANGE AND MAY
NOT BE REFERRED TO AS AN INTERNATIONAL
STANDARD UNTIL PUBLISHED AS SUCH.
IN ADDITION TO THEIR EVALUATION AS
ISO/CEN PARALLEL PROCESSING
BEING ACCEPTABLE FOR INDUSTRIAL,
TECHNOLOGICAL, COMMERCIAL AND
USER PURPOSES, DRAFT INTERNATIONAL
STANDARDS MAY ON OCCASION HAVE TO
BE CONSIDERED IN THE LIGHT OF THEIR
POTENTIAL TO BECOME STANDARDS TO
WHICH REFERENCE MAY BE MADE IN
Reference number
NATIONAL REGULATIONS.
ISO/DIS 19932-3:2017(E)
RECIPIENTS OF THIS DRAFT ARE INVITED
TO SUBMIT, WITH THEIR COMMENTS,
NOTIFICATION OF ANY RELEVANT PATENT
RIGHTS OF WHICH THEY ARE AWARE AND TO
©
PROVIDE SUPPORTING DOCUMENTATION. ISO 2017
oSIST prEN ISO 19932-3:2017
ISO/DIS 19932-3:2017(E)
© ISO 2017, Published in Switzerland
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form
or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior
written permission. Permission can be requested from either ISO at the address below or ISO’s member body in the country of
the requester.
ISO copyright office
Ch. de Blandonnet 8 • CP 401
CH-1214 Vernier, Geneva, Switzerland
Tel. +41 22 749 01 11
Fax +41 22 749 09 47
copyright@iso.org
www.iso.org
ii © ISO 2017 – All rights reserved
oSIST prEN ISO 19932-3:2017
ISO/DIS 19932-3:2017(E)
Contents Page
Foreword .iv
Introduction .v
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Requirements and method of verification . 2
4.1 General requirements . 2
4.2 Harness . 2
4.3 Spray tank . 2
4.4 Dynamic leak test . 3
4.4.1 Leak test when not spraying . 3
4.4.2 Leak test while spraying . 3
4.5 Controls . 3
4.6 Hoses . 3
4.7 Filters . 3
4.8 Spray lance and nozzles . 4
5 Specific requirements for lever-operated knapsack sprayers. 4
5.1 Spray tank . 4
6 Specific requirements for engine – or electric motor-driven knapsack sprayers .4
6.1 Spray tank . 4
6.2 Controls . 4
6.3 Power driven components . 5
6.4 Fuel tank . 5
6.5 Exhaust system . 5
6.6 Parts under high voltage . 5
7 Specific requirements for compression sprayers . 5
7.1 Spray tank . 5
8 Information for use . 5
Annex ZA (informative) Relationship between this European Standard and the Essential
Requirements of EU Directive 2006/42/EC amended by Directive 2009/127/EC
aimed to be covered . 6
Bibliography . 7
oSIST prEN ISO 19932-3:2017
ISO/DIS 19932-3:2017(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.
The main task of technical committees is to prepare International Standards. Draft International
Standards adopted by the technical committees are circulated to the member bodies for voting.
Publication as an International Standard requires approval by at least 75 % of the member bodies
casting a vote.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights.
ISO 19932-3 was prepared by Technical Committee ISO/TC 23, Tractors and machinery for agriculture
and forestry, Subcommittee SC 6, Equipment for crop protection.
iv © ISO 2017 – All rights reserved
oSIST prEN ISO 19932-3:2017
ISO/DIS 19932-3:2017(E)
Introduction
There are three main reasons for inspection in use of knapsack sprayers which are the most widely
used means worldwide of applying Plant Protection Products (PPPs):
— less potential risk to the operator;
— less potential risk of environmental contamination by PPPs; and
— good control of pests with the minimum possible input of PPPs.
In order to use PPPs in agricultural production safely, it is necessary to define the requirements
and test methods for knapsack sprayers in use. This is a relevant step after having standardized
minimum requirements for new knapsack sprayers, in respect of safety hazards and potential risks of
environmental contamination (see ISO 19932-1 and −2).
Standardising the requirements and methods for inspection of sprayers in use takes into consideration
not only the original performance of the sprayer, but also its use, care and maintenance. This is the
logical link to ensure the continued benefit arising from the supply of new sprayers of good quality.
The inspection of sprayers in use can be a mandatory requirement or adopted on a voluntary basis. In
both cases further requirements, outside the scope of this standard, are necessary for the management
of inspections. These include, for example, requirements for the competence of persons carrying out
inspections and the frequency of inspections.
NOTE National or regional regulations may also apply concerning the qualifications and competence of
inspectors.
oSIST prEN ISO 19932-3:2017
oSIST prEN ISO 19932-3:2017
DRAFT INTERNATIONAL STANDARD ISO/DIS 19932-3:2017(E)
Equipment for crop protection — Knapsack sprayers —
Part 3:
Inspection of knapsack sprayers in use
1 Scope
This part of ISO 19932 specifies the requirements and test methods for the inspection in use of Knapsack
sprayers carried on the back or shoulder of the operator for use with Plant Protection Products (PPPs).
It is applicable to lever-operated knapsack sprayers, knapsack compression sprayers and knapsack
sprayers driven by an engine or electric motor using hydraulic pressure atomisation of the spray liquid,
intended for use primarily in agriculture, forestry and horticulture, with a nominal volume of more
than 6.0 l.
The requirements relate mainly to the condition of the sprayer with respect to its potential risk to the
operator and the environment and its performance to achieve good application.
It does not apply to knapsack combustion engine-driven air-blast sprayers according to ISO/DIS 28139,
Controlled Droplet Application equipment utilising rotary atomisers, or portable application equipment
for spatial application (e.g. foggers).
2 Normative references
The following referenced documents are indispensable for the application of this document. For dated
references, only the edition cited applies. For undated references, the latest edition of the referenced
document (including any amendments) applies.
1)
)
ISO 5681 , Equipment for crop protection — Vocabulary
3 Terms and definitions
For the purposes of this document, the terms and definitions given in ISO 5681 and the following apply.
ISO and IEC maintain terminological databases for use in standardization at the following addresses:
— IEC Electropedia: available at http:// www .electropedia .org/
— ISO Online browsing platform: available at http:// www .iso .org/ obp
3.1
knapsack sprayer
self-contained sprayer carried on the operator’s back or shoulder by means of straps or a strap
)
1) Under revision.
oSIST prEN ISO 19932-3:2017
ISO/DIS 19932-3:2017(E)
4 Requirements and method of verification
4.1 General requirements
4.1.1 A calibrated pressure indicator, measuring jug/cylinder (at least 1 l capacit
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.