EN ISO 17078-1:2004

SLOVENSKI STANDARD
01-april-2005
Industrija za predelavo nafte in zemeljskega plina - Vrtalna in proizvodna oprema -
1. del: Vpenjalna os s stranskimi žepi (ISO 17078-1:2004)
Petroleum and natural gas industries - Drilling and production equipment - Part 1: Side-
pocket mandrels (ISO 17078-1:2004)
Erdöl- und Erdgasindustrie - Bohr-und Fördereinrichtungen - Teil 1: Seitentaschen-Rohre
(ISO 17078-1:2004
Industries du pétrole et du gaz naturel - Equipement de forage et de production - Partie
1: Raccords a poche latérale (ISO 17078:2004)
Ta slovenski standard je istoveten z: EN ISO 17078-1:2004
ICS:
75.180.10 Oprema za raziskovanje in Exploratory and extraction
odkopavanje equipment
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EUROPEAN STANDARD
EN ISO 17078-1
NORME EUROPÉENNE
EUROPÄISCHE NORM
December 2004
ICS 75.180.10
English version
Petroleum and natural gas industries - Drilling and production
equipment - Part 1: Side-pocket mandrels (ISO 17078-1:2004)
Industries du pétrole et du gaz naturel - Equipement de
forage et de production - Partie 1: Raccords à poche
latérale (ISO 17078:2004)
This European Standard was approved by CEN on 17 November 2004.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the Central Secretariat or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the official
versions.
CEN members are the national standards bodies of Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France,
Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Slovakia,
Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: rue de Stassart, 36  B-1050 Brussels
© 2004 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 17078-1:2004: E
worldwide for CEN national Members.

Foreword
This document (EN ISO 17078-1:2004) has been prepared by Technical Committee ISO/TC
67 "Materials, equipment and offshore structures for petroleum and natural gas industries" in
collaboration with Technical Committee CEN/TC 12 "Materials, equipment and offshore
structures for petroleum and natural gas industries", the secretariat of which is held by
AFNOR.
This European Standard shall be given the status of a national standard, either by publication
of an identical text or by endorsement, at the latest by June 2005, and conflicting national
standards shall be withdrawn at the latest by June 2005.

According to the CEN/CENELEC Internal Regulations, the national standards organizations of
the following countries are bound to implement this European Standard: Austria, Belgium,
Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary,
Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland,
Portugal, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.

Endorsement notice
The text of ISO 17078-1:2004 has been approved by CEN as EN ISO 17078-1:2004 without
any modifications.
INTERNATIONAL ISO
STANDARD 17078-1
First edition
2004-12-15
Petroleum and natural gas industries —
Drilling and production equipment —
Part 1:
Side-pocket mandrels
Industries du pétrole et du gaz naturel — Équipement de forage et de
production —
Partie 1: Raccords à poche latérale

Reference number
ISO 17078-1:2004(E)
©
ISO 2004
ISO 17078-1:2004(E)
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but
shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In
downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat
accepts no liability in this area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation
parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In
the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.

©  ISO 2004
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or
ISO's member body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland
ii © ISO 2004 – All rights reserved

ISO 17078-1:2004(E)
Contents Page
Foreword. iv
Introduction . v
1 Scope. 1
2 Normative references. 1
3 Terms and definitions. 2
4 Abbreviated terms. 7
5 Functional specification. 7
5.1 General. 7
5.2 Functional characteristics. 7
5.3 Well parameters. 8
5.4 Operational parameters. 9
5.5 Compatibility with related well devices . 9
5.6 Environmental service classes. 10
5.7 Design validation. 10
5.8 Product functional testing grades. 10
5.9 Quality-control grades. 10
5.10 Additional requirements. 10
6 Technical specification. 11
6.1 General. 11
6.2 Technical characteristics. 11
6.3 Design criteria. 12
6.4 Design verification. 13
6.5 Allowable design changes . 13
6.6 Design validation. 14
6.7 Product-functional testing requirements . 14
7 Supplier/manufacturer requirements. 15
7.1 General. 15
7.2 Documentation and data control. 15
7.3 Product identification requirements . 17
7.4 Quality-control requirement. 17
7.5 Heat treatment requirements . 19
7.6 Welding requirements. 20
7.7 Non-destructive examination (NDE) requirements. 20
7.8 Storage and shipping preparation . 22
7.9 Repair. 23
Annex A (normative) Environmental-service requirements. 24
Annex B (normative) Design-validation requirements . 26
Annex C (normative) Product-functional testing requirements . 30
Annex D (normative) Quality-control requirements. 33
Annex E (informative) Operating performance envelope . 35
Annex F (informative) Schematics of side-pocket mandrels . 38
Bibliography . 40

ISO 17078-1:2004(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies
(ISO member bodies). The work of preparing International Standards is normally carried out through ISO
technical committees. Each member body interested in a subject for which a technical committee has been
established has the right to be represented on that committee. International organizations, governmental and
non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the
International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.
The main task of technical committees is to prepare International Standards. Draft International Standards
adopted by the technical committees are circulated to the member bodies for voting. Publication as an
International Standard requires approval by at least 75 % of the member bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. ISO shall not be held responsible for identifying any or all such patent rights.
ISO 17078-1 was prepared by Technical Committee ISO/TC 67, Materials, equipment and offshore structures
for petroleum, petrochemical and natural gas industries, Subcommittee SC 4, Drilling and production
equipment.
ISO 17078 consists of the following parts, under the general title Petroleum and natural gas industries —
Drilling and production equipment:
 Part 1: Side-pocket mandrels
The following parts are under preparation:
 Part 2: Side-pocket mandrel gas lift valve and flow control devices
 Part 3: Latches, seals, and interface data for side-pocket mandrels and flow control devices
iv © ISO 2004 – All rights reserved

ISO 17078-1:2004(E)
Introduction
This part of ISO 17078 has been developed by users/purchasers and suppliers/manufacturers of side-pocket
mandrel products intended for use in the worldwide petroleum and natural gas industry. This part of
ISO 17078 is intended to provide requirements and information to all parties who are involved in the
specification, selection, manufacture, testing and use of side-pocket mandrel products. Further, t
...