Materials obtained from End of Life Tyres - Determination of specific requirements for sampling and determination of moisture content using the oven-dry method

This document specifies a method for determining the total moisture content of materials obtained from End of Life Tyres (ELT) by drying samples in an oven. The method is applicable to chips, granulates, powders and textile derived from the treatment of End of Life Tyres.
This document is not intended for the determination of moisture content in steel wires.

Materialien aus Altreifen - Bestimmung der spezifischen Anforderungen für die Probenahme und Bestimmung des Feuchtegehaltes aus dem Ofen-Trockenverfahren

Dieses Dokument legt ein Verfahren zur Bestimmung des Gesamtfeuchtegehaltes von Materialien aus Altreifen (en: End of Life Tyres – ELT) durch das Trocknen von Proben in einem Ofen fest. Das Verfahren gilt für Schnitzel, Granulate, Pulver und Textilien, die aus der Verarbeitung von Altreifen stammen.
Dieses Dokument ist nicht für die Bestimmung des Feuchtegehaltes von Stahldrähten vorgesehen.

Matériaux obtenus à partir de pneus usagés non réutilisables (PUNR) - Détermination des exigences spécifiques relatives à l’échantillonnage et détermination de la teneur en humidité selon la méthode de séchage à l’étuve

No Scope Available

Snovi iz izrabljenih avtomobilskih gum - Določanje specifičnih zahtev za vzorčenje in ugotavljanje deleža vlage z uporabo sušilnika

General Information

Status
Not Published
Publication Date
15-Dec-2024
Current Stage
4599 - Dispatch of FV draft to CMC - Finalization for Vote
Start Date
10-May-2024
Due Date
17-Jun-2024
Completion Date
10-May-2024

Relations

Buy Standard

Draft
prEN 16916:2023 - BARVE
English language
11 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

SLOVENSKI STANDARD
oSIST prEN 16916:2023
01-september-2023
Nadomešča:
SIST-TS CEN/TS 16916:2016
Snovi iz izrabljenih avtomobilskih gum - Določanje specifičnih zahtev za vzorčenje
in ugotavljanje deleža vlage z uporabo sušilnika
Materials obtained from End of Life Tyres - Determination of specific requirements for
sampling and determination of moisture content using the oven-dry method
Materialien aus Altreifen - Bestimmung der spezifischen Anforderungen für die
Probenahme und Bestimmung des Feuchtegehaltes aus dem Ofen-Trockenverfahren
Matériaux obtenus à partir de pneus usagés non réutilisables (PUNR) - Détermination
des exigences spécifiques relatives à l’échantillonnage et détermination de la teneur en
humidité selon la méthode de séchage à l’étuve
Ta slovenski standard je istoveten z: prEN 16916
ICS:
13.030.50 Recikliranje Recycling
83.160.01 Avtomobilske pnevmatike na Tyres in general
splošno
oSIST prEN 16916:2023 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------
oSIST prEN 16916:2023

---------------------- Page: 2 ----------------------
oSIST prEN 16916:2023


DRAFT
EUROPEAN STANDARD
prEN 16916
NORME EUROPÉENNE

EUROPÄISCHE NORM

July 2023
ICS 13.030.50; 83.160.01 Will supersede CEN/TS 16916:2016
English Version

Materials obtained from End of Life Tyres - Determination
of specific requirements for sampling and determination of
moisture content using the oven-dry method
 Materialien aus Altreifen - Bestimmung der
spezifischen Anforderungen für die Probenahme und
Bestimmung des Feuchtegehaltes aus dem Ofen-
Trockenverfahren
This draft European Standard is submitted to CEN members for enquiry. It has been drawn up by the Technical Committee
CEN/TC 366.

If this draft becomes a European Standard, CEN members are bound to comply with the CEN/CENELEC Internal Regulations
which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.

This draft European Standard was established by CEN in three official versions (English, French, German). A version in any other
language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC
Management Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Türkiye and
United Kingdom.

Recipients of this draft are invited to submit, with their comments, notification of any relevant patent rights of which they are
aware and to provide supporting documentation.

Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without
notice and shall not be referred to as a European Standard.


EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2023 CEN All rights of exploitation in any form and by any means reserved Ref. No. prEN 16916:2023 E
worldwide for CEN national Members.

---------------------- Page: 3 ----------------------
oSIST prEN 16916:2023
prEN 16916:2023 (E)
Contents Page
European foreword . 3
1 Scope . 4
2 Normative references . 4
3 Terms and definitions . 4
4 Principle . 4
5 Apparatus . 4
6 Preparation of the sampling plan and laboratory sample . 4
6.1 Principles of sampling . 4
6.1.1 General .
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.