EN ISO 4545-1:2018
(Main)Metallic materials - Knoop hardness test - Part 1: Test method (ISO 4545-1:2017)
Metallic materials - Knoop hardness test - Part 1: Test method (ISO 4545-1:2017)
ISO 4545-1:2017 specifies the Knoop hardness test method for metallic materials for test forces from 0,009 807 N to 19,613 N.
The Knoop hardness test is specified in this document for lengths of indentation diagonals ≥0,020 mm. Using this method to determine Knoop hardness from smaller indentations is outside the scope of this document as results would suffer from large uncertainties due to the limitations of optical measurement and imperfections in tip geometry. ISO 14577-1 allows the determination of hardness from smaller indentations.
A periodic verification method is specified for routine checking of the testing machine in service by the user.
Special considerations for Knoop testing of metallic coatings can be found in ISO 4516.
Metallische Werkstoffe - Härteprüfung nach Knoop - Teil 1: Prüfverfahren (ISO 4545-1:2017)
Dieses Dokument legt das Verfahren für die Härteprüfung nach Knoop an metallischen Werkstoffen für Prüfkräfte von 0,009 807 N bis 19,613 N fest.
In diesem Dokument ist die Härteprüfung nach Knoop festgelegt für Eindruckdiagonallängen ≥ 0,020 mm. Die Verwendung dieses Verfahrens zur Bestimmung der Knoop-Härte für kleinere Eindrücke gehört nicht zum Anwendungsbereich in diesem Dokument, weil die Resultate wegen Grenzen der optischen Messung und Unvollkommenheiten der Kegelgeometrie mit großer Unsicherheit behaftet wären. ISO 14577 1 erlaubt die Härte-Bestimmung von kleineren Eindrücken.
Eine periodische Überprüfung ist angegeben zur laufenden Kontrolle der Prüfmaschine in Betrieb durch den Anwender.
Besondere Überlegungen zur Prüfung metallischer Überzüge nach Knoop können ISO 4516 entnommen werden.
Matériaux métalliques - Essai de dureté Knoop - Partie 1: Méthode d'essai (ISO 4545-1:2017)
ISO 4545-1:2017 spécifie la méthode d'essai de dureté Knoop pour les matériaux métalliques, pour des forces d'essai comprises entre 0,009 807 N et 19,613 N.
Le présent document spécifie l'essai de dureté Knoop pour les longueurs de diagonale d'empreinte ≥ 0,020 mm. L'utilisation de cette méthode pour déterminer la dureté Knoop d'empreintes plus petites ne fait pas partie du domaine d'application du présent document, car les résultats ainsi obtenus présenteraient des incertitudes élevées en raison des limitations du mesurage optique et des imperfections concernant la géométrie de la pointe. L'ISO 14577‑1 permet de déterminer la dureté des empreintes plus petites.
Une méthode de vérification périodique est spécifiée pour la vérification de routine, par l'utilisateur, de la machine d'essai utilisée.
Des considérations particulières pour les essais Knoop des revêtements métalliques sont disponibles dans l'ISO 4516.
Kovinski materiali - Preskus trdote po Knoopu - 1. del: Preskusna metoda (ISO 4545-1:2017)
Ta dokument določa metodo za preskus trdote po Knoopu za kovinske materiale s preskusnimi silami od 0,009 807 N do 19,613 N.
Preskus trdote po Knoopu je v tem dokumentu določen za dolžine diagonal zarez ≥ 0,020 mm. Uporaba te metode za določanje trdote po Knoopu na podlagi manjših zarez ne sodi v področje uporabe tega dokumenta, saj bi bili rezultati nezanesljivi zaradi negotovosti, povezane z omejitvami optičnega merjenja in nepravilnostmi geometrije konice. Določevanje trdote na podlagi manjših zarez omogoča standard ISO 14577-1.
Določena je tudi metoda za redno preverjanje pri rutinskem pregledovanju naprave za preskušanje, ki jo uporablja
uporabnik. Posebne zahteve za preskušanje kovinskih prevlek so navedene v standardu ISO 4516.
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
01-julij-2018
1DGRPHãþD
SIST EN ISO 4545-1:2006
Kovinski materiali - Preskus trdote po Knoopu - 1. del: Preskusna metoda (ISO
4545-1:2017)
Metallic materials - Knoop hardness test - Part 1: Test method (ISO 4545-1:2017)
Metallische Werkstoffe - Härteprüfung nach Knoop - Teil 1: Prüfverfahren (ISO 4545-
1:2017)
Matériaux métalliques - Essai de dureté Knoop - Partie 1 : Méthode d'essai (ISO 4545-
1:2017)
Ta slovenski standard je istoveten z: EN ISO 4545-1:2018
ICS:
77.040.10 Mehansko preskušanje kovin Mechanical testing of metals
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
EN ISO 4545-1
EUROPEAN STANDARD
NORME EUROPÉENNE
March 2018
EUROPÄISCHE NORM
ICS 77.040.10 Supersedes EN ISO 4545-1:2005
English Version
Metallic materials - Knoop hardness test - Part 1: Test
method (ISO 4545-1:2017)
Matériaux métalliques - Essai de dureté Knoop - Partie Metallische Werkstoffe - Härteprüfung nach Knoop -
1: Méthode d'essai (ISO 4545-1:2017) Teil 1: Prüfverfahren (ISO 4545-1:2017)
This European Standard was approved by CEN on 30 November 2017.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2018 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 4545-1:2018 E
worldwide for CEN national Members.
Contents Page
European foreword . 3
European foreword
This document (EN ISO 4545-1:2018) has been prepared by Technical Committee ISO/TC 164
“Mechanical testing of metals” in collaboration with Technical Committee ECISS/TC 101 “Test methods
for steel (other than chemical analysis)” the secretariat of which is held by AFNOR.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by September 2018, and conflicting national standards
shall be withdrawn at the latest by September 2018.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN ISO 4545-1:2005.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia,
France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta,
Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and the United Kingdom.
Endorsement notice
The text of ISO 4545-1:2017 has been approved by CEN as EN ISO 4545-1:2018 without any
modification.
INTERNATIONAL ISO
STANDARD 4545-1
Second edition
2017-12
Metallic materials — Knoop
hardness test —
Part 1:
Test method
Matériaux métalliques — Essai de dureté Knoop —
Partie 1: Méthode d'essai
Reference number
ISO 4545-1:2017(E)
©
ISO 2017
ISO 4545-1:2017(E)
© ISO 2017, Published in Switzerland
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form
or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior
written permission. Permission can be requested from either ISO at the address below or ISO’s member body in the country of
the requester.
ISO copyright office
Ch. de Blandonnet 8 • CP 401
CH-1214 Vernier, Geneva, Switzerland
Tel. +41 22 749 01 11
Fax +41 22 749 09 47
copyright@iso.org
www.iso.org
ii © ISO 2017 – All rights reserved
ISO 4545-1:2017(E)
Contents Page
Foreword .iv
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Principle . 1
5 Symbols and designations . 2
5.1 Symbols and designations used in this document . 2
5.2 Designation of hardness number . 3
6 Testing machine . 3
6.1 Testing machine . 3
6.2 Indenter . . 3
6.3 Diagonal measuring system . 4
7 Test piece . 4
7.1 Test Surface . 4
7.2 Preparation . 4
7.3 Thickness . 4
7.4 Support of unstable test pieces . 4
8 Procedure. 5
8.1 Test temperature . 5
8.2 Test force . 5
8.3 Periodic verification . 5
8.4 Test piece support . 5
8.5 Focus on test surface . 5
8.6 Test force application . 6
8.7 Prevention of the effect of shock or vibration . 6
8.8 Minimum distance between adjacent indentations . 6
8.9 Measurement of diagonal length . 7
8.10 Calculation of hardness value . 7
9 Uncertainty of the results . 7
10 Test report . 7
Annex A (normative) Procedure for periodic checking of the testing machine, diagonal
measuring system and the indenter by the user . 9
Annex B (informative) Uncertainty of the measured hardness values .11
Annex C (informative) Knoop hardness measurement traceability .18
Annex D (informative) CCM — Working group on hardness .22
Annex E (informative) Adjustment of Köhler illumination systems .23
Bibliography .24
ISO 4545-1:2017(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received (see www.iso.org/patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation on the voluntary nature of standards, the meaning of ISO specific terms and
expressions related to conformity assessment, as well as information about ISO's adhe
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.