Aerospace series - Installation hole for fluid fittings, flanged

This standard specifies the dimensions of the installation holes and the design bosses and installation recesses for flanged fluid to EN 3630 and EN 3631, and method of callout on drawings.

Luft- und Raumfahrt - Einbaulöcher für Rohrverbindungen mit Flansch

Diese Norm legt die Maße der Einbaulöcher und die Ausführung der Vor- und Rücksprünge für Rohrver¬bindungen mit Flansch nach EN 3630 und EN 3631 sowie ein Verfahren zur Angabe in Zeichnungen fest.

Série aérospatiale - Trous d'implantation pour raccords à bride

Aeronavtika - Luknja za vgradnjo cevne napeljave s prirobnico

General Information

Status
Published
Publication Date
27-May-2008
Withdrawal Date
29-Nov-2008
Technical Committee
Current Stage
9093 - Decision to confirm - Review Enquiry
Completion Date
30-Jun-2017

Buy Standard

Standard
EN 3633:2008
English language
8 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)


SLOVENSKI STANDARD
01-september-2008
Aeronavtika - Luknja za vgradnjo cevne napeljave s prirobnico
Aerospace series - Installation hole for fluid fittings, flanged
Luft- und Raumfahrt - Einbaulöcher für Rohrverbindungen mit Flansch
Série aérospatiale - Trous d'implantation pour raccords à bride
Ta slovenski standard je istoveten z: EN 3633:2008
ICS:
49.080 /HWDOVNLLQYHVROMVNL Aerospace fluid systems and
KLGUDYOLþQLVLVWHPLLQGHOL components
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EUROPEAN STANDARD
EN 3633
NORME EUROPÉENNE
EUROPÄISCHE NORM
May 2008
ICS 49.080
English Version
Aerospace series - Installation hole for fluid fittings, flanged
Série aérospatiale - Trous d'implantation pour raccords à Luft- und Raumfahrt - Einbaulöcher für Rohrverbindungen
bride mit Flansch
This European Standard was approved by CEN on 21 December 2007.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the CEN Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as the
official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland,
France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,
Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: rue de Stassart, 36  B-1050 Brussels
© 2008 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 3633:2008: E
worldwide for CEN national Members.

Contents Page
Foreword.3
1 Scope .4
2 Normative references .4
3 Required characteristics.4
3.1 Configuration, dimensions, tolerances .4
4 Hole dimensions .5
5 Design of bosses and installation recesses .6
5.1 Bosses .6
5.2 Recesses .7
6 Indication on drawings.7
6.1 Example 1 .7
6.2 Example 2 .8
7 Designation .8

Figures
Figure 1 . 5
Figure 2 . 6
Figure 3 . 7
Figure 4 .
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.