prEN ISO 10350-1

SLOVENSKI STANDARD
01-september-2024
Polimerni materiali - Pridobitev in predstavitev primerljivih značilnih enotočkovnih
podatkov - 1. del: Materiali za oblikovanje (ISO/DIS 10350-1:2024)
Plastics - Acquisition and presentation of comparable single-point data - Part 1: Moulding
materials (ISO/DIS 10350-1:2024)
Kunststoffe - Ermittlung und Darstellung vergleichbarer Einpunktkennwerte - Teil 1:
Formmassen (ISO/DIS 10350-1:2024)
Plastiques - Acquisition et présentation de caractéristiques intrinsèques comparables -
Partie 1: Matériaux pour moulage (ISO/DIS 10350-1:2024)
Ta slovenski standard je istoveten z: prEN ISO 10350-1
ICS:
83.080.20 Plastomeri Thermoplastic materials
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

DRAFT
International
Standard
ISO/DIS 10350-1
ISO/TC 61/SC 2
Plastics — Acquisition and
Secretariat: KATS
presentation of comparable single-
Voting begins on:
point data —
2024-06-18
Part 1:
Voting terminates on:
2024-09-10
Moulding materials
Plastiques — Acquisition et présentation de caractéristiques
intrinsèques comparables —
Partie 1: Matériaux pour moulage
ICS: 83.080.20
THIS DOCUMENT IS A DRAFT CIRCULATED
FOR COMMENTS AND APPROVAL. IT
IS THEREFORE SUBJECT TO CHANGE
AND MAY NOT BE REFERRED TO AS AN
INTERNATIONAL STANDARD UNTIL
PUBLISHED AS SUCH.
This document is circulated as received from the committee secretariat.
IN ADDITION TO THEIR EVALUATION AS
BEING ACCEPTABLE FOR INDUSTRIAL,
TECHNOLOGICAL, COMMERCIAL AND
USER PURPOSES, DRAFT INTERNATIONAL
STANDARDS MAY ON OCCASION HAVE TO
ISO/CEN PARALLEL PROCESSING
BE CONSIDERED IN THE LIGHT OF THEIR
POTENTIAL TO BECOME STANDARDS TO
WHICH REFERENCE MAY BE MADE IN
NATIONAL REGULATIONS.
RECIPIENTS OF THIS DRAFT ARE INVITED
TO SUBMIT, WITH THEIR COMMENTS,
NOTIFICATION OF ANY RELEVANT PATENT
RIGHTS OF WHICH THEY ARE AWARE AND TO
PROVIDE SUPPORTING DOCUMENTATION.
Reference number
ISO/DIS 10350-1:2024(en)
DRAFT
ISO/DIS 10350-1:2024(en)
International
Standard
ISO/DIS 10350-1
ISO/TC 61/SC 2
Plastics — Acquisition and
Secretariat: KATS
presentation of comparable single-
Voting begins on:
point data —
Part 1:
Voting terminates on:
Moulding materials
Plastiques — Acquisition et présentation de caractéristiques
intrinsèques comparables —
Partie 1: Matériaux pour moulage
ICS: 83.080.20
THIS DOCUMENT IS A DRAFT CIRCULATED
FOR COMMENTS AND APPROVAL. IT
IS THEREFORE SUBJECT TO CHANGE
AND MAY NOT BE REFERRED TO AS AN
INTERNATIONAL STANDARD UNTIL
PUBLISHED AS SUCH.
This document is circulated as received from the committee secretariat.
IN ADDITION TO THEIR EVALUATION AS
BEING ACCEPTABLE FOR INDUSTRIAL,
© ISO 2024
TECHNOLOGICAL, COMMERCIAL AND
USER PURPOSES, DRAFT INTERNATIONAL
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
STANDARDS MAY ON OCCASION HAVE TO
ISO/CEN PARALLEL PROCESSING
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on
BE CONSIDERED IN THE LIGHT OF THEIR
the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below
POTENTIAL TO BECOME STANDARDS TO
WHICH REFERENCE MAY BE MADE IN
or ISO’s member body in the country of the requester.
NATIONAL REGULATIONS.
ISO copyright office
RECIPIENTS OF THIS DRAFT ARE INVITED
CP 401 • Ch. de Blandonnet 8
TO SUBMIT, WITH THEIR COMMENTS,
CH-1214 Vernier, Geneva
NOTIFICATION OF ANY RELEVANT PATENT
Phone: +41 22 749 01 11
RIGHTS OF WHICH THEY ARE AWARE AND TO
PROVIDE SUPPORTING DOCUMENTATION.
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland Reference number
ISO/DIS 10350-1:2024(en)
ii
ISO/DIS 10350-1:2024(en)
Contents Page
Foreword .iv
Introduction .v
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 3
4 Specimen preparation and conditioning . 3
5 Test requirements . 4
6 Presentation of results . 4
Bibliography .10

iii
ISO/DIS 10350-1:2024(en)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out through
ISO technical committees. Each member body interested in a subject for which a technical committee
has been established has the right to be represented on that committee. International organizations,
governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely
with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are described
in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the different types
of ISO documents should be noted. This document was drafted in accordance with the editorial rules of the
ISO/IEC Directives, Part 2 (see www.iso.org/directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of any patent
rights identified during the development of the document will be in the Introduction and/or on the ISO list of
patent declarations received (see www.iso.org/patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation on the voluntary nature of standards, the meaning of ISO specific terms and
expressions related to conformity assessment, as well as information about ISO's adherence to the World
Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT) see the following URL:
www.iso.org/iso/foreword.html.
This document was prepared by Technical Committee ISO/TC 61, Plastics, Subcommittee SC 2, Mechanical
behavior.
This forth edition cancels and replaces the third edition (ISO 10350-1:2012), which has been technically
revised.
The main changes are as follows;
— In “specimen type” column of Table 2, write specimen dimensions and specimen types of corresponding
ISO 20753 jointly.
— The subscripts of the signsσ of stress at break and strain at break of figure 1 is changed from “B” to “b”
to match ISO 527-1. For example ; σ to σ
B b
— Correct an explanation formula of the x-axis. “ε = …” to “ε =…”.
t
— Corrects “2.12, Charpy impact strength” of Table 2 in “2.12, Charpy unnotched impact strength”.
A list of all parts in the ISO 10350 series can be found on the ISO website.

iv
ISO/DIS 10350-1:2024(en)
Introduction
The ISO 10350 series has been prepared because users of plastics find that available data cannot always be
readily used to compare the properties of similar materials, especially when the data have been supplied
by different sources. Even when the same standard tests have been used, they often allow the adoption
of a wide range of alternative test conditions, and the data obtained are not necessarily comparable. The
purpose of this document is to identify specific methods and conditions of test to be used for the acquisition
and presentation of data in order that valid comparisons between materials can be made.
The ISO 10350 series is concerned with tests employed to present “single-point” data on the limited range of
properties commonly included in data sheets and used for the preliminary selection of materials. Such data
represent the most basic approach to the specification of properties of materials, and the ISO 10350 series
thus facilitates the first steps towards more efficient selection and use of plastics in the many applications to
which they are suited.
Complementary International Standards (ISO 11403-1, ISO 11403-2 and ISO 11403-3) are concerned with
the standardized acquisition and presentation of multipoint data, to demonstrate how properties vary
with important factors such as time, temperature and the presence of particular natural and chemical
environments. In these documents, some additional properties are included. Their use will provide a more
substantial database than one containing only single-point data, and so will enable improved assessment of
the fitness of a material for any particular application. In addition, ISO 11403-1, which deals with mechanical
properties, assists predictions of the performance of components and ISO 11403-2, covering thermal
and processing properties, aids predictions of melt-flow behaviour during manufacturing. ISO 11403-3
is concerned with environmental influences on properties, and other parts may be prepared to cover
additional properties.
v
DRAFT International Standard ISO/DIS 10350-1:2024(en)
Plastics — Acquisition and presentation of comparable
single-point data —
Part 1:
Moulding materials
1 Scope
The ISO 10350 series identifies specific test procedures for the acquisition and presentation of comparable
data for certain basic properties of plastics. In general, each property is specified by a single experimental
value, although in certain cases properties are represented by two values obtained under different test
conditions. The properties included are those presented conventionally in manufacturers' data sheets. This
document applies predominantly to unreinforced and reinforced thermoplastic and thermosetting materials
that may be injection- or compression-moulded or prepared as sheets of specified thickness.
NOTE ISO 10350-2 deals specifically with long- or continuous-fibre-reinforced plastics. For the purpose of this
document, long-fibre-reinforced plastics are considered to have fibre length greater than 7,5 mm prior to moulding.
2 Normative references
The following documents are referred to in the text in such a way that some or all of their content constitutes
requirements of this document. For dated references, only the edition cited applies. For undated references,
the latest edition of the referenced document (including any amendments) applies.
ISO 62, Plastics — Determination of water absorption
ISO 75-1, Plastics — Determination of temperature of deflection under load — Part 1: General test method
ISO 75-2, Plastics — Determination of temperature of deflection under load — Part 2: Plastics and ebonite
ISO 178, Plastics — Determination of flexural properties
ISO 179-1, Plastics — Determination of Charpy impact properties — Part 1: Non-instrumented impact test
ISO 179-2, Plastics — Determination of Charpy impact properties — Part 2: Instrumented impact test
ISO 293, Plastics — Compression moulding of test specimens of thermoplastic materials
ISO 294-1, Plastics — Injection moulding of test specimens of thermoplastic materials — Part 1: General
principles, and moulding of multipurpose and bar test specimens
ISO 294-3, Plastics — Injection moulding of test specimens of thermoplastic materials — Part 3: Small plates
ISO 294-4, Plastics — Injection moulding of test specimens of thermoplastic materials — Part 4: Determination
of moulding shrinkage
ISO 295, Plastics — Compression moulding of test specimens of thermosetting materials
ISO 306, Plastics — Thermoplastic materials — Determination of Vicat softening temperature (VST)
ISO 527-1, Plastics — Determination of tensile properties — Part 1: General principles
ISO 527-2, Plastics — Determination of tensile properties — Part 2: Test conditions for moulding and extrusion
plastics
ISO/DIS 10350-1:2024(en)
ISO 899-1, Plastics — Determination of creep behaviour — Part 1: Tensile creep
ISO 1133-1, Plastics — Determination of the melt mass-flow rate (MFR) and melt volume-flow rate (MVR) of
thermoplastics — Part 1: Standard method
ISO 1133-2, Plastics — Determination of the melt mass-flow rate (MFR) and melt volume-flow rate (MVR) of
thermoplastics — Part 2: Method for materials sensitive to time-temperature history and/or moisture
ISO 1183-1,
...