EN 4534-2:2009
(Main)Aerospace series - Bushes, plain in aluminium alloy with self-lubricating liner, elevated load - Part 2: Dimensions and loads - Inch series
Aerospace series - Bushes, plain in aluminium alloy with self-lubricating liner, elevated load - Part 2: Dimensions and loads - Inch series
This standard specifies the characteristics of plain bushes in aluminium alloy with self-lubricating liner,
elevated load for aerospace applications.
The bushes are intended for use in fixed or moving parts of the aircraft structure and control mechanisms.
They shall be used in the temperature range - 55 °C to 121 °C.
Luft- und Raumfahrt - Buchsen aus Aluminiumlegierung, mit selbstschmierender Beschichtung, erhöhte Belastung - Teil 2: Maße und Belastungen - Inch-Reihe
Die vorliegende Norm legt die Eigenschaften von Buchsen aus Aluminiumlegierung mit selbstschmierender Beschichtung, erhöhter Belastung, für die Anwendung in der Luft- und Raumfahrt fest.
Die Buchsen sind für den Einsatz in starren oder beweglichen Teilen der Luftfahrzeugstruktur und der Betätigungsvorrichtungen vorgesehen.
Sie sind für den Einsatz im Temperaturbereich von - 55 °C bis 121 °C bestimmt.
Série aérospatiale - Bagues en alliage d'aluminium à garniture autolubrifiante, charge élevée - Partie 2 : Dimensions et charges - Série en inches
Aeronavtika - Drsne puše iz aluminijeve zlitine s samomazalno oblogo, serija za večje obremenitve - 2. del: Mere in nosilnosti - Colski tip
General Information
- Status
- Withdrawn
- Publication Date
- 09-Jun-2009
- Withdrawal Date
- 20-Jan-2026
- Technical Committee
- ASD-STAN - Aerospace
- Drafting Committee
- ASD-STAN/D 3 - Mechanical
- Current Stage
- 9093 - Decision to confirm - Review Enquiry
- Start Date
- 30-Jun-2017
- Completion Date
- 28-Jan-2026
Relations
- Effective Date
- 14-Sep-2016
- Effective Date
- 28-Jan-2026
- Effective Date
- 28-Jan-2026
- Refers
EN 2284:1991 - Aerospace series - Sulphuric acid anodizing of aluminium and wrought aluminium alloys - Effective Date
- 28-Jan-2026
- Effective Date
- 28-Jan-2026
- Refers
EN 2311:2017 - Aerospace series - Bushes with self-lubricating liner - Technical specification - Effective Date
- 28-Jan-2026
- Refers
EN 2101:1991 - Aerospace series - Chromic acid anodizing of aluminium and wrought aluminium alloys - Effective Date
- 28-Jan-2026
Get Certified
Connect with accredited certification bodies for this standard
National Aerospace and Defense Contractors Accreditation Program (NADCAP)
Global cooperative program for special process quality in aerospace.
NSF-ISR
NSF International Strategic Registrations.
Orion Registrar Inc.
US-based certification body for management systems.
Sponsored listings
Frequently Asked Questions
EN 4534-2:2009 is a standard published by the European Committee for Standardization (CEN). Its full title is "Aerospace series - Bushes, plain in aluminium alloy with self-lubricating liner, elevated load - Part 2: Dimensions and loads - Inch series". This standard covers: This standard specifies the characteristics of plain bushes in aluminium alloy with self-lubricating liner, elevated load for aerospace applications. The bushes are intended for use in fixed or moving parts of the aircraft structure and control mechanisms. They shall be used in the temperature range - 55 °C to 121 °C.
This standard specifies the characteristics of plain bushes in aluminium alloy with self-lubricating liner, elevated load for aerospace applications. The bushes are intended for use in fixed or moving parts of the aircraft structure and control mechanisms. They shall be used in the temperature range - 55 °C to 121 °C.
EN 4534-2:2009 is classified under the following ICS (International Classification for Standards) categories: 49.035 - Components for aerospace construction. The ICS classification helps identify the subject area and facilitates finding related standards.
EN 4534-2:2009 has the following relationships with other standards: It is inter standard links to EN 4534-2:2016, EN 2318:1992, EN 2424:2008, EN 2284:1991, EN 12631:1999, EN 2311:2017, EN 2101:1991. Understanding these relationships helps ensure you are using the most current and applicable version of the standard.
EN 4534-2:2009 is available in PDF format for immediate download after purchase. The document can be added to your cart and obtained through the secure checkout process. Digital delivery ensures instant access to the complete standard document.
Standards Content (Sample)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Luft- und Raumfahrt - Buchsen aus Aluminiumlegierung, mit selbstschmierender Beschichtung, erhöhte Belastung - Teil 2: Maße und Belastungen - Inch ReiheSérie aérospatiale - Bagues en alliage d'aluminium à garniture autolubrifiante, charge élevée - Partie 2 : Dimensions et charges - Série en inchesAerospace series - Bushes, plain in aluminium alloy with self-lubricating liner, elevated load - Part 2: Dimensions and loads - Inch series49.035Sestavni deli za letalsko in vesoljsko gradnjoComponents for aerospace construction49.025.20AluminijAluminiumICS:Ta slovenski standard je istoveten z:EN 4534-2:2009SIST EN 4534-2:2009en01-september-2009SIST EN 4534-2:2009SLOVENSKI
STANDARD
EUROPEAN STANDARDNORME EUROPÉENNEEUROPÄISCHE NORMEN 4534-2June 2009ICS 49.035 English VersionAerospace series - Bushes, plain in aluminium alloy with self-lubricating liner, elevated load - Part 2: Dimensions and loads -Inch seriesSérie aérospatiale - Bagues en alliage d'aluminium àgarniture autolubrifiante, charge élevée - Partie 2 :Dimensions et charges - Série en inchesLuft- und Raumfahrt - Buchsen aus Aluminiumlegierung,mit selbstschmierender Beschichtung, erhöhte Belastung -Teil 2: Maße und Belastungen - Inch ReiheThis European Standard was approved by CEN on 24 April 2009.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this EuropeanStandard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such nationalstandards may be obtained on application to the CEN Management Centre or to any CEN member.This European Standard exists in three official versions (English, French, German). A version in any other language made by translationunder the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as theofficial versions.CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland,France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMITÉ EUROPÉEN DE NORMALISATIONEUROPÄISCHES KOMITEE FÜR NORMUNGManagement Centre:
Avenue Marnix 17,
B-1000 Brussels© 2009 CENAll rights of exploitation in any form and by any means reservedworldwide for CEN national Members.Ref. No. EN 4534-2:2009: ESIST EN 4534-2:2009
ISO 2768-1, General tolerances — Part 1: Tolerances for linear and angular dimensions without individual tolerance indications 3 Terms and definitions For the purposes of this document, the terms and definitions given in TR 4475 apply. 4 Requirements 4.1 Configuration, dimensions, tolerances and mass According to Figure 1 and Tables 1 and 2. Dimensions apply after surface treatment. Dimensions and tolerances are expressed in millimetres (inches). General tolerances shall be ISO 2768-m in accordance with ISO 2768-1. 4.2 Surface roughness According to Figure 1.
1) Published as ASD Technical Report at the date of publication of this standard. SIST EN 4534-2:2009
Key a Chamfer machined before bonding b Chamfer or radius at manufacturers option c Chamfer machined after bonding Figure 1 — Configuration SIST EN 4534-2:2009
d D a . Nominal diameter 0 − 0,025 ± 0,013
± 2° (0 − 0.0010) (± 0.0005)
04 6,350 (0.2500) 6,388 (0.2515) 9,550 (0.3760) 0,50 to 0,75 (0.020 to 0.030) 15° 05 7,938 (0.3125) 7,976 (0.3140) 11,140 (0.4386) 06 9,525 (0.3750) 9,563 (0.3765) 12,730 (0.5012) 07 11,113 (0.4375) 11,151 (0.4390) 14,321 (0.5638) 08 12,700 (0.5000) 12,738 (0.5015) 15,913 (0.6265) 09 14,288 (0.5625) 14,326 (0.5640) 17,506 (0.6892) 10 15,875 (0.6250) 15,913 (0.6265) 20,681 (0.8142) 11 17,463 (0.6875) 17,501 (0.6890) 22,268 (0.8767) 12 19,050 (0.7500) 19,088 (0.7515) 23,858 (0.9393) 14 22,225 (0.8750) 22,263 (0.8765) 27,038 (1.0645) 16 25,400 (1.0000) 25,438 (1.0015) 30,221 (1.1898) 18 28,575 (1.1250) 28,613 (1.1265) 33,396 (1.3148) 20 31,750 (1.2500) 31,788 (1.2515) 36,571 (1.4398) 22 34,925 (1.3750) 34,963 (1.3765) 39,746 (1.5648) 24 38,100 (1.5000) 38,138 (1.5015) 44,508 (1.7523) 26 41,275 (1.6250) 41,313 (1.6265) 47,683 (1.8773) 28 44,450 (1.7500) 44,488 (1.7515) 50,858 (2.0023) 32 50,800 (2.0000) 50,838 (2.0015) 57,208 (2.2523) a Diameter code corresponds to nominal diameter d in 1/16 inch.
00,25−
(00.010−) 3,97 4,76 5,56 6,35 7,14 7,94 8,73 9,53 11,11 12,70 14,29 15,88 17,46 19,05 22,23 (0.156) (0.188) (0.219) (0.250) (0.281)(0.313)(0.344)(0.375)(0.438)(0.500)(0.563) (0.625) (0.688)(0.750)(0.875)Mass in kg/1 000 pieces ≈ 04 0,44 0,53 0,62 0,70 0,79 0,88 0,97 1,06 1,23 — — — — — — 05 0,53 0,63 0,74 0,84 0,95 1,06 1,16 1,27 1,48 1,69 1,90 — — — — 06 0,62 0,74 0,86 0,99 1,11 1,23 1,36 1,48 1,73 1,97 2,22 2,47 2,71 — — 07 0,70 0,85 0,99 1,13 1,27 1,41 1,55 1,69 1,97 2,26 2,54 2,82 3,10 3,38 3,95 08 0,79 0,95 1,11 1,27 1,43 1,59 1,75 1,91 2,22 2,54 2,86 3,18 3,49 3,81 4,45 0
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.
Loading comments...