iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
CEN

EN ISO 12058-1:2002/AC:2004

(Corrigendum)

Plastics - Determination of viscosity using a falling-ball viscometer - Part 1: Inclined-tube method (ISO 12058-1:1997)

Plastics - Determination of viscosity using a falling-ball viscometer - Part 1: Inclined-tube method (ISO 12058-1:1997)

TC - Superseding note updated in line with EN ISO 9371:1995/AC:2004

Kunststoffe - Bestimmung der Viskosität mit einem Kugelfallviskosimeter - Teil 1: Verfahren nach Höppler (ISO 12058-1:1997)

Plastiques - Détermination de la viscosité au moyen d'un viscosimètre à chute de bille - Partie 1: Méthode du tube incliné (ISO 12058-1:1997)

Polimerni materiali - Določanje viskoznosti z uporabo viskozimetra s padajočo kroglico - 1. del: Metoda z nagnjeno cevjo (ISO 12058-1:1997)

General Information

Status
Withdrawn
Publication Date
21-Sep-2004
ICS
83.080.01 - Plastics in general
Technical Committee
CEN/TC 249 - Plastics
Drafting Committee
CEN/TC 249 - Plastics
Current Stage
9960 - Withdrawal effective - Withdrawal
Completion Date
22-Aug-2018
Ref Project
SIST EN ISO 12058-1:2003/AC:2005 - Plastics - Determination of viscosity using a falling-ball viscometer - Part 1: Inclined-tube method (ISO 12058-1:1997)

Relations

Replaced By
EN ISO 12058-1:2018 - Plastics - Determination of viscosity using a falling-ball viscometer - Part 1: Inclined-tube method (ISO 12058-1:2018)
Effective Date
29-Aug-2018
Corrects
EN ISO 12058-1:2002 - Plastics - Determination of viscosity using a falling-ball viscometer - Part 1: Inclined-tube method (ISO 12058-1:1997)
Effective Date
08-Jun-2022

Buy Standard

EN ISO 12058-1:2003/AC:2005EN ISO 12058-1:2003/AC:2005
PreviousNext
Corrigendum
EN ISO 12058-1:2003/AC:2005
English, French and German language
2 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)


2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Kunststoffe - Bestimmung der Viskosität mit einem Kugelfallviskosimeter - Teil 1: Verfahren nach Höppler (ISO 12058-1:1997)Plastiques - Détermination de la viscosité au moyen d'un viscosimetre a chute de bille - Partie 1: Méthode du tube incliné (ISO 12058-1:1997)Plastics - Determination of viscosity using a falling-ball viscometer - Part 1: Inclined-tube method (ISO 12058-1:1997)83.080.01Polimerni materiali na splošnoPlastics in generalICS:Ta slovenski standard je istoveten z:EN ISO 12058-1:2002/AC:2004SIST EN ISO 12058-1:2003/AC:2005en,fr,de01-marec-2005SIST EN ISO 12058-1:2003/AC:2005SLOVENSKI
STANDARD
EUROPEAN STANDARD NORME EUROPÉENNE EUROPÄISCHE NORM
EN ISO 12058-1:2002/AC
September 2004
Septembre 2004
September 2004 ICS 83.080.01 English version Version Française Deutsche Fassung
Plastics - Determination of viscosity using a falling-ball viscometer - Part 1: Inclined-tube method (ISO 12058-1:1997)
Plastiques - Détermination de la viscosité au moyen d'un viscosimètre à chute de bille - Partie 1: Méthode du tube incliné (ISO 12058-1:1997)
Kunststoffe - Bestimmung der Viskosität mit einem Kugelfallviskosimeter - Teil 1: Verfahren nach Höppler (ISO 12058-1:1997) This corrigendum becomes effective on 22 September 2004 for incorporation in the three official language versions of the EN.
Ce corrigendum prendra effet le 22 septembre 2004 pour incorporation dans les trois versions linguistiques officielles
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

CEN
EN ISO 899-2:2024(Main)
Plastics - Determination of creep behaviour - Part 2: Flexural creep by three-point loading (ISO 899-2:2024)
SIST EN ISO 899-2:2024

This document specifies a method for determining the flexural creep of plastics in the form of standard test specimens under specified conditions such as those of pre-treatment, temperature and humidity. It is only applicable to a simple freely supported beam loaded at mid-span (three-point-loading test).
 The method is suitable for use with rigid and semi-rigid non-reinforced, filled and fibre-reinforced plastics materials (see ISO 472 for definitions) test specimens moulded directly or machined from sheets or moulded articles.
NOTE            The method can be unsuitable for certain fibre-reinforced materials due to differences in fibre orientation
The method is intended to provide data for engineering-design, quality control, research and development purposes.
The method might not be applicable for determining the flexural creep of rigid cellular plastics (attention is drawn in this respect to ISO 1209-1 and ISO 1209-2).

  • Standard
    23 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 4892-3:2024(Main)
Plastics - Methods of exposure to laboratory light sources - Part 3: Fluorescent UV lamps (ISO 4892-3:2024)
SIST EN ISO 4892-3:2024

This document specifies methods for exposing plastic specimens to fluorescent UV lamp radiation, heat and water in apparatus designed to simulate the weathering effects that occur when plastic materials are exposed in actual end-use environments to global solar radiation, or to window-glass filtered solar radiation.
Fluorescent UV lamp exposures for paints, varnishes and other coatings are described in ISO 16474-3.

  • Standard
    26 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 4892-1:2024(Main)
Plastics - Methods of exposure to laboratory light sources - Part 1: General guidance and requirements (ISO 4892-1:2024)
SIST EN ISO 4892-1:2024

This document provides general guidance and requirements relevant to the selection and operation of the methods of exposure described in detail in subsequent parts of the ISO 4892 series. It also specifies general performance requirements for devices used for exposing plastics to laboratory light sources. Information regarding performance requirements is for producers of artificial accelerated weathering or artificial accelerated irradiation devices.
This document also provides information on the interpretation of data from artificial accelerated weathering or artificial accelerated irradiation exposures. More specific information about methods for determining the change in the properties of plastics after exposure and reporting these results is not part of this document.

  • Standard
    37 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 9773:2024(Main)
Plastics - Determination of burning behaviour of thin flexible vertical specimens in contact with a small-flame ignition source (ISO 9773:2024)
SIST EN ISO 9773:2024

This document specifies a small-scale laboratory screening procedure for comparing the relative burning behaviour of vertically oriented thin and relatively flexible plastics specimens exposed to a low-energy-level flame ignition source.
NOTE  These specimens cannot be tested using method B of IEC 60695-11-10:2013 since they distort or shrink away from the applied flame source without igniting.
This test method determines the afterflame and afterglow times of specimens.
The classification system described in Annex A is intended for quality control and the preselection of component materials for products. The classification established by this method of test is applicable only to the material used for the specimens.
NOTE  Test results are influenced by material components, e.g. pigments, fillers, concentrations of fire retardants.

  • Standard
    19 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 15347-1:2024(Main)
Plastics - Sorted plastics wastes - Part 1: General characterisation
SIST EN 15347-1:2024

This document provides a scheme for the characterization of sorted plastics wastes, laying out those properties for which the supplying party of the waste makes information available to the receiving party. This document provides for a division of information between "Required Data", where a statement is required, and additional "Optional Data" as agreed between the supplying and receiving party.
This document is the general part of a series on sorted plastics wastes. This document does not cover the description of quality grades per polymer(s) and stream as well as test methods specific to each plastic waste stream; these aspects are addressed in the other parts of EN 15347.

  • Standard
    14 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 22007-1:2024(Main)
Plastics - Determination of thermal conductivity and thermal diffusivity - Part 1: General principles (ISO 22007-1:2024)
SIST EN ISO 22007-1:2024

This document describes the background to methods for the determination of the thermal conductivity and thermal diffusivity of polymeric materials. Different techniques are available for these measurements and some can be better suited than others for a particular type, state and form of material. This document provides a broad overview of these techniques. Standards specific to these techniques, as referenced in this document, are used to carry out the actual test method.

  • Standard
    26 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 22007-4:2024(Main)
Plastics - Determination of thermal conductivity and thermal diffusivity - Part 4: Light flash method (ISO 22007-4:2024)
SIST EN ISO 22007-4:2024

This document specifies a method for the determination of the thermal diffusivity of a thin solid disc of plastics in the thickness direction by the light flash method. This method is based upon the measurement of the temperature rise at the rear face of the thin-disc specimen produced by a short energy pulse on the front face.
The method is applicable to homogeneous solid plastics as well as composites having an isotropic or orthotropic structure. In general, it covers materials having a thermal diffusivity, α, in the range 1 × 10−7 m2⋅s−1 < α < 1 × 10−4 m2⋅s−1. Measurements can be carried out in gaseous and vacuum environments over a temperature range from −100 °C to +400 °C.
NOTE          For inhomogeneous specimens, the measured values can be specimen thickness dependent.

  • Standard
    23 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 8256:2023(Main)
Plastics - Determination of tensile-impact strength (ISO 8256:2023)
SIST EN ISO 8256:2024

1.1     This document specifies two methods (method A and method B) for the determination of the tensile-impact strength of plastics under defined conditions. The tests can be described as tensile tests at relatively high strain rates. These methods can be used for rigid materials (as defined in ISO 472), but are especially useful for materials too flexible or too thin to be tested with impact tests conforming to the ISO 179 series or ISO 180.
1.2     These methods are used for investigating the behaviour of specified specimens under specified impact velocities, and for estimating the brittleness or the toughness of specimens within the limitations inherent in the test conditions.
1.3     These methods are applicable both to specimens prepared from moulding materials and to specimens taken from finished or semi-finished products (for example mouldings, laminates, or extruded or cast sheets).
1.4     Results obtained by testing moulded specimens of different dimensions are not necessarily the same. Equally, it is possible that specimens cut from moulded products will not give the same results as specimens of the same dimensions moulded directly from the material. Test results obtained from specimens prepared from moulding compounds cannot be applied directly to mouldings of any given shape, because values may depend on the design of the moulding and the moulding conditions. Results obtained by method A and method B can or can not be comparable.
1.5     These methods are not suitable for use as a source of data for design calculations on components. Information on the typical behaviour of a material can be obtained, however, by testing different types of test specimen prepared under different conditions, and by testing at different temperatures. The two different methods are suitable for production control as well as for quality control.

  • Standard
    23 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 20753:2023(Main)
Plastics - Test specimens (ISO 20753:2023)
SIST EN ISO 20753:2024

This document specifies dimensional requirements relating to test specimens prepared from plastics materials intended for processing by moulding, as well as to test specimens prepared by machining from sheets or shaped articles. It compiles the designations and dimensions of test specimens used for the acquisition of comparable data and of other frequently used specimens.
The following types of test specimen are specified:
A            Tensile specimen, multipurpose or reduced-scale
B            Bar specimen
C            Small tensile specimen
D            Square plate specimen
F            Rectangular plate specimen
NOTE    If a particular type of test specimen is not mentioned in this document, this does not mean that there is any intention to exclude the use of the specimen. Additional specimen types can be added in future if they are commonly used.

  • Standard
    23 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 61:2023(Main)
Plastics - Determination of apparent density of moulding material that cannot be poured from a specified funnel (ISO 61:2023)
SIST EN ISO 61:2023

This document specifies a method of determining the apparent density, i.e. the mass per unit of volume, of loose material that cannot be poured from a funnel of specified design.
NOTE            For a method of determining the apparent density of loose moulding material that can be poured from a specified funnel, see ISO 60.
This document is applicable to loose moulding materials such as slice, granular or powder.

  • Standard
    12 pages
    English language
    sale 10% off
    e-Library read for
    1 day