CEN/TR 1335-4:2009
(Main)Office furniture - Office work chair - Part 4: Clarifications to EN 1335-1:2000 (Dimensions)
Office furniture - Office work chair - Part 4: Clarifications to EN 1335-1:2000 (Dimensions)
This Technical Report specifies the definitions of a number of terms given in EN 1335-1:2000, which have been identified by CEN/TC 207/SC 3/WG 1 as being interpreted in different ways by test laboratories and manufacturers.
Büromöbel - Büro-Arbeitsstuhl - Teil 4: Auslegungen zu EN 1335-1:2000 (Maße)
Dieser Technische Bericht legt die Definitionen für eine Anzahl von Begriffen in EN 1335-1:2000 fest, die, wie von CEN/TC 207/SC 3/WG 1 ermittelt, von Prüfstellen und Herstellern verschieden ausgelegt wurden.
Mobilier de bureau - Sièges de travail de bureau - Partie 4: Clarifications apportées à l'EN 1335-1:2000 (Dimensions)
Le présent Rapport Technique précise les définitions d’un certain nombre de termes donnés dans l’EN 1335-1:2000, qui ont été identifiés par le CEN/TC 207/SC 3/WG 1 comme étant interprétés différemment par les laboratoires d’essais et les fabricants.
Pisarniško pohištvo - Pisarniški delovni stoli - 4. del: Pojasnila k EN 1335-1:2000 (Mere)
To tehnično poročilo določa definicije več izrazov, navedenih v EN 1335-1:2000, za katere je CEN/TC 207/SC 3/WG 1 ugotovil, da si jih preskusni laboratoriji in proizvajalci razlagajo na različne načine.
General Information
Standards Content (Sample)
SLOVENSKI STANDARD
01-januar-2010
Pisarniško pohištvo - Pisarniški delovni stoli - 4. del: Pojasnila k EN 1335-1:2000
(Mere)
Office furniture - Office work chair - Part 4: Clarifications to EN 1335-1:2000
(Dimensions)
Büromöbel - Büro-Arbeitsstuhl - Teil 4: Auslegungen zu EN 1335-1:2000 (Maße)
Mobilier de bureau - Sièges de travail de bureau - Partie 4: Clarifications apportées à
l'EN 1335-1:2000 (Dimensions)
Ta slovenski standard je istoveten z: CEN/TR 1335-4:2009
ICS:
97.140 Pohištvo Furniture
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
TECHNICAL REPORT
CEN/TR 1335-4
RAPPORT TECHNIQUE
TECHNISCHER BERICHT
October 2009
ICS 97.140
English Version
Office furniture - Office work chair - Part 4: Clarifications to EN
1335-1:2000 (Dimensions)
Mobilier de bureau - Sièges de travail de bureau - Partie 4: Büromöbel - Büro-Arbeitsstuhl - Teil 4: Auslegungen zu EN
Clarifications apportées à l'EN 1335-1:2000 (Dimensions) 1335-1:2000 (Maße)
This Technical Report was approved by CEN on 8 September 2009. It has been drawn up by the Technical Committee CEN/TC 207.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland,
France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,
Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2009 CEN All rights of exploitation in any form and by any means reserved Ref. No. CEN/TR 1335-4:2009: E
worldwide for CEN national Members.
Contents Page
Foreword .3
Introduction .4
1 Scope .5
2 Normative references .5
3 Clarifications .5
3.1 Adjustable .5
3.1.1 General .5
3.1.2 Independently adjustable .5
3.1.3 Dependently adjustable .5
3.2 Determination of point "S" .5
3.3 Position of seat and back rest .6
3.4 Seat height .6
3.5 Adjustable seat depth .6
3.6 Inclination of seat surface .6
3.7 Adjustable backrest inclination .6
3.8 Length of armrest .6
3.9 Height of arm rest .6
3.10 Clear width between the arm rests .7
3.11 Definition of chair types A, B and C .7
Annex A (informative) Example for a measuring device for the dimensions of arm rests .8
Foreword
This document (CEN/TR 1335-4:2009) has been prepared by Technical Committee CEN/TC 207 “Furniture”,
the secretariat of which is held by UNI.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights.
Introduction
Dur
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.