ASTM B283/B283M-14
(Specification)Standard Specification for Copper and Copper-Alloy Die Forgings (Hot-Pressed)
Standard Specification for Copper and Copper-Alloy Die Forgings (Hot-Pressed)
ABSTRACT
This specification establishes the requirements for copper and copper die forgings produced by hot pressing method. The forgings included here are designated with the following Copper or Copper Alloy UNS Nos.: C11000 (copper), C14500 (copper-tellurium alloy), C14700 (copper-sulfur alloy), C36500 (leaded Muntz metal), C37000 (free-cutting Muntz metal), C37700 (forging brass), C46400 (naval brass), C48200 (medium leaded naval brass), C48500 (leaded naval brass), C61900 (aluminum bronze), C62300 (9% aluminum bronze), C63000 and C63200 (aluminum-nickel bronze), C64200 (aluminum-silicon bronze), C64210 (6.7% aluminum-silicon bronze), C65500 (high-silicon bronze), C67500 (manganese bronze), C67600, C69300 (copper-zinc-silicon alloy), C70620 (90% copper-10% nickel alloy), C71520 (70% copper-30% nickel alloy), and C77400 (45% nickel-10% silver alloy). The materials for manufacture shall be rods, billets, or blanks of such purity and soundness as to be suitable for processing by hot pressing. Products shall be tested to examine their conformance to mechanical (tensile and yield strengths, and elongation), dimensional, and chemical composition requirements.
SCOPE
1.1 This specification establishes the requirements for copper and copper alloy die forgings produced by the hot pressing method. The following copper and copper alloys are included:
Copper or Copper Alloy
UNS No.
Name
C11000
copper
C14500
copper-tellurium
C14700
copper-sulfur
C27450
plumbing brass
C27451
plumbing brass
C35330
leaded brass
C36500
leaded Muntz metal
C37000
free-cutting Muntz metal
C37700
forging brass
C46400
naval brass
C48200
medium leaded naval brass
C48500
leaded naval brass
C48600
naval brass
C49250
copper-zinc-bismuth alloy
C49255
copper-zinc-bismuth-nickel alloy
C49260
copper-zinc-bismuth alloy
C49300
copper-zinc-tin-bismuth alloy
C49340
copper-zinc-tin-bismuth alloy
C49350
copper-zinc-tin-bismuth alloy
C49355
bismuth brass
C61900
aluminum bronze
C62300
aluminum bronze, 9 %
C63000
aluminum-nickel bronze
C63200
aluminum-nickel bronze
C64200
aluminum-silicon bronze
C64210
aluminum-silicon bronze, 6.7 %
C65500
high-silicon bronze (A)
C67500
manganese bronze (A)
C67600
. . .
C69300
copper-zinc-silicon
C70620
copper-nickel 90-10
C71520
copper-nickel 70-30
C77400
nickel silver, 45-10
C87700
silicon bronze
C87710
silicon bronze
1.2 Units—The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.Note 1—Nominal composition and relative forgeability ratings are given in Appendix X1. Copper-nickel alloys C70620 and C71520 are intended for welded applications with seawater exposure.Note 2—Wrought product intended for hot forging is described in Specification B124/B124M.
1.3 The following safety caveat pertains only to Section 10 of this specification. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
General Information
Relations
Buy Standard
Standards Content (Sample)
NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation:B283/B283M −14
StandardSpecification for
1
Copper and Copper-Alloy Die Forgings (Hot-Pressed)
This standard is issued under the fixed designation B283/B283M; the number immediately following the designation indicates the year
of original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval.
A superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
This standard has been approved for use by agencies of the U.S. Department of Defense.
1. Scope* values stated in each system may not be exact equivalents;
therefore,eachsystemshallbeusedindependentlyoftheother.
1.1 This specification establishes the requirements for cop-
Combining values from the two systems may result in non-
per and copper alloy die forgings produced by the hot pressing
conformance with the standard.
method. The following copper and copper alloys are included:
NOTE 1—Nominal composition and relative forgeability ratings are
given in Appendix X1. Copper-nickel alloys C70620 and C71520 are
Copper or Copper Alloy
intended for welded applications with seawater exposure.
UNS No. Name
NOTE 2—Wrought product intended for hot forging is described in
Specification B124/B124M.
C11000 copper
1.3 The following safety caveat pertains only to Section 10
C14500 copper-tellurium
C14700 copper-sulfur
of this specification. This standard does not purport to address
C27450 plumbing brass
all of the safety concerns, if any, associated with its use. It is
C27451 plumbing brass
the responsibility of the user of this standard to establish
C35330 leaded brass
C36500 leaded Muntz metal
appropriate safety and health practices and determine the
C37000 free-cutting Muntz metal
applicability of regulatory limitations prior to use.
C37700 forging brass
C46400 naval brass
C48200 medium leaded naval brass 2. Referenced Documents
C48500 leaded naval brass
2
2.1 ASTM Standards:
C48600 naval brass
C49250 copper-zinc-bismuth alloy
B124/B124M Specification for Copper and Copper Alloy
C49255 copper-zinc-bismuth-nickel alloy
Forging Rod, Bar, and Shapes
C49260 copper-zinc-bismuth alloy
B249/B249M Specification for General Requirements for
C49300 copper-zinc-tin-bismuth alloy
C49340 copper-zinc-tin-bismuth alloy
Wrought Copper and Copper-Alloy Rod, Bar, Shapes and
C49350 copper-zinc-tin-bismuth alloy
Forgings
C49355 bismuth brass
B846 Terminology for Copper and Copper Alloys
C61900 aluminum bronze
C62300 aluminum bronze, 9 %
E8/E8M Test Methods for Tension Testing of Metallic Ma-
C63000 aluminum-nickel bronze
terials
C63200 aluminum-nickel bronze
E62 Test Methods for Chemical Analysis of Copper and
C64200 aluminum-silicon bronze
3
C64210 aluminum-silicon bronze, 6.7 %
CopperAlloys(PhotometricMethods)(Withdrawn2010)
C65500 high-silicon bronze (A)
E75 Test Methods for Chemical Analysis of Copper-Nickel
C67500 manganese bronze (A)
3
and Copper-Nickel-Zinc Alloys (Withdrawn 2010)
C67600 . . .
C69300 copper-zinc-silicon
E478 Test Methods for ChemicalAnalysis of CopperAlloys
C70620 copper-nickel 90-10
2.2 Other Standards:
C71520 copper-nickel 70-30
C77400 nickel silver, 45-10
ISO 7602 Determination of Tellurium Content (High
C87700 silicon bronze
Content)—Flame Atomic Absorption Spectrometric
C87710 silicon bronze
4
Method
1.2 Units—The values stated in either SI units or inch-
pound units are to be regarded separately as standard. The
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or
contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM
1
ThisspecificationisunderthejurisdictionofASTMCommitteeB05onCopper Standards volume information, refer to the standard’s Document Summary page on
and CopperAlloys and is the direct responsibility of Subcommittee B05.02 on Rod, the ASTM website.
3
Bar, Wire, Shapes and Forgings. The last approved version of this historical standard is referenced on
Current edition approved April 1, 2014. Published May 2014. Originally www.astm.org.
4
approved in 1953. Last previous edition approved in 2012 as B283/B283M – 12. Available fromAmerican National Standards Institute (ANSI), 25 W. 43rd St.,
DOI: 10.1520/B0283_B0283M-14. 4th Floor, New York, NY 10036, http://www.ansi.org.
*A Summary of Changes section appears at the end of this standard
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1
---------------------- Page: 1 ----------------------
B283/B283M−14
JIS H 1068:2005 Method for Determination of Bismuth in 5.1.7 When product must adhere to the requirements of
5
Copper and Copper Alloys (Japanese Industrial Stan- ASME Boiler and Pressure Vessel Code (Mechanical Property
dards) Requirements).
6
2.3 Military Standards:
5.2 The following requirements are optional and shall be
MIL-
...
This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
Designation: B283/B283M − 12 B283/B283M − 14
Standard Specification for
1
Copper and Copper-Alloy Die Forgings (Hot-Pressed)
This standard is issued under the fixed designation B283/B283M; the number immediately following the designation indicates the year
of original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval.
A superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
This standard has been approved for use by agencies of the U.S. Department of Defense.
1. Scope*
1.1 This specification establishes the requirements for copper and copper alloy die forgings produced by the hot pressing
method. The following copper and copper alloys are included:
Copper or Copper Alloy
UNS No. Name
C11000 copper
C14500 copper-tellurium
C14700 copper-sulfur
C27450 plumbing brass
C27451 plumbing brass
C35330 leaded brass
C36500 leaded Muntz metal
C37000 free-cutting Muntz metal
C37700 forging brass
C46400 naval brass
C48200 medium leaded naval brass
C48500 leaded naval brass
C48600 naval brass
C49250 copper-zinc-bismuth alloy
C49255 copper-zinc-bismuth-nickel alloy
C49260 copper-zinc-bismuth alloy
C49300 copper-zinc-tin-bismuth alloy
C49340 copper-zinc-tin-bismuth alloy
C49350 copper-zinc-tin-bismuth alloy
C49355 bismuth brass
C61900 aluminum bronze
C62300 aluminum bronze, 9 %
C63000 aluminum-nickel bronze
C63200 aluminum-nickel bronze
C64200 aluminum-silicon bronze
C64210 aluminum-silicon bronze, 6.7 %
C65500 high-silicon bronze (A)
C67500 manganese bronze (A)
C67600 . . .
C69300 copper-zinc-silicon
C70620 copper-nickel 90-10
C71520 copper-nickel 70-30
C77400 nickel silver, 45-10
C87700 silicon bronze
C87710 silicon bronze
1.2 Units—The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated
in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values
from the two systems may result in non-conformance with the standard.
NOTE 1—Nominal composition and relative forgeability ratings are given in Appendix X1. Copper-nickel alloys C70620 and C71520 are intended for
welded applications with seawater exposure.
NOTE 2—Wrought product intended for hot forging is described in Specification B124/B124M.
1
This specification is under the jurisdiction of ASTM Committee B05 on Copper and Copper Alloys and is the direct responsibility of Subcommittee B05.02 on Rod, Bar,
Wire, Shapes and Forgings.
Current edition approved April 1, 2012April 1, 2014. Published May 2012May 2014. Originally approved in 1953. Last previous edition approved in 20112012 as
B283/B283M – 11a.B283/B283M – 12. DOI: 10.1520/B0283_B0283M-12.10.1520/B0283_B0283M-14.
*A Summary of Changes section appears at the end of this standard
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1
---------------------- Page: 1 ----------------------
B283/B283M − 14
1.3 The following safety caveat pertains only to Section 10 of this specification. This standard does not purport to address all
of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate
safety and health practices and determine the applicability of regulatory limitations prior to use.
2. Referenced Documents
2
2.1 ASTM Standards:
B124/B124M Specification for Copper and Copper Alloy Forging Rod, Bar, and Shapes
B249/B249M Specification for General Requirements for Wrought Copper and Copper-Alloy Rod, Bar, Shapes and Forgings
B846 Terminology for Copper and Copper Alloys
E8/E8M Test Methods for Tension Testing of Metallic Materials
3
E62 Test Methods for Chemical Analysis of Copper and Copper Alloys (Photometric Methods) (Withdrawn 2010)
3
E75 Test Methods for Chemical Analysis of Copper-Nickel and Copper-Nickel-Zinc Alloys (Withdrawn 2010)
E478 Test Methods for Chemical Analysis of Copper Alloys
2.2 Other Standards:
4
ISO 7602 Determination of Tellurium Content (High Content)—Flame Atomic Absorption Spectrometric Method
5
JIS H 1068:2005 Method for Determination of Bismuth in Copper and Copper Alloys (Japanese Industrial Standards)
6
2.3 Military Standards:
MIL-STD-792 Identification Marking Requirements for Special Purpose Components
NAVSEA T9074-AS-GIB-010/271 Requirements for Nondestructive Testing Method
3. General Requirements
3.1 The following sections of Specification B249/B249M constitute a part of this specifica
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.