Standard Specification for Metal Insert Fittings Utilizing a Copper Crimp Ring for SDR9 Cross-linked Polyethylene (PEX) Tubing and SDR9 Polyethylene of Raised Temperature (PE-RT) Tubing

ABSTRACT
This specification covers metal insert fittings and copper crimp rings for use with SDR9 cross-linked polyethylene (PEX) tubing. All performance tests shall be performed on assemblies of fittings, crimp rings, and PEX tubing. Fittings and crimp rings shall meet the material and dimensional requirements prescribed. The sealing surfaces of the insert shall be smooth and free of foreign material. Fitting walls shall be free of cracks, holes, blisters, voids, foreign inclusions, or other defects that are visible to the unaided eye and affect the wall integrity. Insert fittings shall be joined to PEX tubing by the compression of a copper crimp ring around the outer circumference of the tubing, forcing the tubing material into annular spaces formed by ribs on the fitting.
SCOPE
1.1 This specification covers metal insert fittings and copper crimp rings for use with cross-linked polyethylene (PEX) tubing in 3/8 , 1/2 , 5/8 , 3/4 , 1, 1 1/4 , 11/2 , and 2 in. nominal diameters that meet the requirements for Specifications F876 and F877 and for use with polyethylene of raised temperature (PE-RT) tubing in 3/8 , 1/2 , 5/8 , 3/4 and 1 in. and 1 1/4 in. nominal diameters that meet the requirements of Specifications F2623 and F2769. These fittings are intended for use in 100 psi (689.5 kPa) cold- and hot-water distribution systems operating at temperatures up to, and including, 180°F (82°C). The requirements for materials, workmanship, dimensions, and markings to be used on the fittings and rings are also included.  
1.2 The values stated in inch-pound units are to be regarded as the standard. The values given in parentheses are mathematical conversions to SI units which are provided for information only and are not considered the standard.  
1.3 Compliance with this specification requires that these fittings be tested and certified to Specification F877 when used with PEX tubing and Specification F2769 when used with PE-RT tubing.  
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

General Information

Status
Historical
Publication Date
31-Jul-2012
Technical Committee
Drafting Committee
Current Stage
Ref Project

Relations

Buy Standard

Technical specification
ASTM F1807-12 - Standard Specification for Metal Insert Fittings Utilizing a Copper Crimp Ring for SDR9 Cross-linked Polyethylene (PEX) Tubing and SDR9 Polyethylene of Raised Temperature (PE-RT) Tubing
English language
7 pages
sale 15% off
Preview
sale 15% off
Preview
Technical specification
REDLINE ASTM F1807-12 - Standard Specification for Metal Insert Fittings Utilizing a Copper Crimp Ring for SDR9 Cross-linked Polyethylene (PEX) Tubing and SDR9 Polyethylene of Raised Temperature (PE-RT) Tubing
English language
7 pages
sale 15% off
Preview
sale 15% off
Preview

Standards Content (Sample)

NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation:F1807 −12 AnAmerican National Standard
Standard Specification for
Metal Insert Fittings Utilizing a Copper Crimp Ring for SDR9
Cross-linked Polyethylene (PEX) Tubing and SDR9
1
Polyethylene of Raised Temperature (PE-RT) Tubing
This standard is issued under the fixed designation F1807; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope* A269 Specification for Seamless and Welded Austenitic
Stainless Steel Tubing for General Service
1.1 This specification covers metal insert fittings and copper
A276 Specification for Stainless Steel Bars and Shapes
crimp rings for use with cross-linked polyethylene (PEX)
A312/A312M Specification for Seamless, Welded, and
3 1 5 3 1 1
tubingin ⁄8, ⁄2, ⁄8, ⁄4,1,1 ⁄4,1 ⁄2,and2in.nominaldiameters
Heavily Cold Worked Austenitic Stainless Steel Pipes
that meet the requirements for Specifications F876 and F877
B16/B16M Specification for Free-Cutting Brass Rod, Bar
and for use with polyethylene of raised temperature (PE-RT)
and Shapes for Use in Screw Machines
3 1 5 3 1
tubing in ⁄8, ⁄2, ⁄8, ⁄4 and 1 in. and 1 ⁄4 in. nominal diameters
B62 Specification for Composition Bronze or Ounce Metal
that meet the requirements of Specifications F2623 and F2769.
Castings
These fittings are intended for use in 100 psi (689.5 kPa) cold-
B75 Specification for Seamless Copper Tube
and hot-water distribution systems operating at temperatures
B88 Specification for Seamless Copper Water Tube
up to, and including, 180°F (82°C). The requirements for
B124/B124M Specification for Copper and Copper Alloy
materials, workmanship, dimensions, and markings to be used
Forging Rod, Bar, and Shapes
on the fittings and rings are also included.
B140/B140M Specification for Copper-Zinc-Lead (Red
1.2 The values stated in inch-pound units are to be regarded
Brass or Hardware Bronze) Rod, Bar, and Shapes
asthestandard.Thevaluesgiveninparenthesesaremathemati-
B283 Specification for Copper and Copper-Alloy Die Forg-
cal conversions to SI units which are provided for information
ings (Hot-Pressed)
only and are not considered the standard.
B371/B371M Specification for Copper-Zinc-Silicon Alloy
Rod
1.3 Compliance with this specification requires that these
fittings be tested and certified to Specification F877 when used B584 Specification for Copper Alloy Sand Castings for
General Applications
with PEX tubing and Specification F2769 when used with
PE-RT tubing. B967/B967M Specification for Copper-Zinc-Tin-Bismuth
Alloy Rod, Bar and Wire
1.4 This standard does not purport to address all of the
D1600 Terminology forAbbreviatedTerms Relating to Plas-
safety concerns, if any, associated with its use. It is the
tics
responsibility of the user of this standard to establish appro-
D2122 Test Method for Determining Dimensions of Ther-
priate safety and health practices and determine the applica-
moplastic Pipe and Fittings
bility of regulatory limitations prior to use.
E18 Test Methods for Rockwell Hardness of Metallic Ma-
2. Referenced Documents terials
2 F412 Terminology Relating to Plastic Piping Systems
2.1 ASTM Standards:
F876 SpecificationforCrosslinkedPolyethylene(PEX)Tub-
ing
1
This standard is under the jurisdiction of ASTM Committee F17 on Plastic
F877 SpecificationforCrosslinkedPolyethylene(PEX)Hot-
Piping Systems and is the direct responsibility of Subcommittee F17.10 on Fittings.
and Cold-Water Distribution Systems
Current edition approved Aug. 1, 2012. Published December 2012. Originally
ε1
F2623 Specification for Polyethylene of RaisedTemperature
approved in 1997. Last previous edition approved in 2011 as F1807 – 11a . DOI:
10.1520/F1807-12.
(PE-RT) SDR 9 Tubing
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or
F2769 Specification for Polyethylene of RaisedTemperature
contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM
(PE-RT) Plastic Hot and Cold-Water Tubing and Distri-
Standards volume information, refer to the standard’s Document Summary page on
the ASTM website. bution Systems
*A Summary of Changes section appears at the end of this standard
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1

---------------------- Page: 1 ----------------------
F1807−12
3
2.2 ASME Standards: B371/B371M Copper Alloy UNS No. C69300, or Standard
B1.20.1 Pipe Threads General Purpose (Inch) EN 12164, CopperAlloy CW614N, or CopperAlloy UNS No.
B16.18 Cast Copper Alloy Solder Joint Pressure Fittings C27450, or Specification B967/B967M copper alloy UNS No.
B16.22 Wrought Copper and Copper Alloy Solder Joint C49260 or C49340.
...

This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
´1
Designation: F1807 − 11a F1807 − 12 An American National Standard
Standard Specification for
Metal Insert Fittings Utilizing a Copper Crimp Ring for SDR9
Cross-linked Polyethylene (PEX) Tubing and SDR9
1
Polyethylene of Raised Temperature (PE-RT) Tubing
This standard is issued under the fixed designation F1807; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1
εNOTE—Footnote 1 and Section 5.1.3 were editorially updated in July 2011.
1. Scope*
1.1 This specification covers metal insert fittings and copper crimp rings for use with cross-linked polyethylene (PEX) tubing
3 1 5 3 1 1
in ⁄8, ⁄2, ⁄8, ⁄4, 1, 1 ⁄4, 1 ⁄2, and 2 in. nominal diameters that meet the requirements for Specifications F876 and F877 and for use
3 1 5 3 1
with polyethylene of raised temperature (PE-RT) tubing in ⁄8, ⁄2, ⁄8, ⁄4 and 1 in. and 1 ⁄4 in. nominal diameters that meet the
requirements of Specifications F2623 and F2769. These fittings are intended for use in 100 psi (689.5 kPa) cold- and hot-water
distribution systems operating at temperatures up to, and including, 180°F (82°C). The requirements for materials, workmanship,
dimensions, and markings to be used on the fittings and rings are also included.
1.2 The values stated in inch-pound units are to be regarded as the standard. The values given in parentheses are mathematical
conversions to SI units which are provided for information only and are not considered the standard.
1.3 Compliance with this specification requires that these fittings be tested and certified to Specification F877 when used with
PEX tubing and Specification F2769 when used with PE-RT tubing.
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility
of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory
limitations prior to use.
2. Referenced Documents
2
2.1 ASTM Standards:
A269 Specification for Seamless and Welded Austenitic Stainless Steel Tubing for General Service
A276 Specification for Stainless Steel Bars and Shapes
A312/A312M Specification for Seamless, Welded, and Heavily Cold Worked Austenitic Stainless Steel Pipes
B16/B16M Specification for Free-Cutting Brass Rod, Bar and Shapes for Use in Screw Machines
B62 Specification for Composition Bronze or Ounce Metal Castings
B75 Specification for Seamless Copper Tube
B88 Specification for Seamless Copper Water Tube
B124/B124M Specification for Copper and Copper Alloy Forging Rod, Bar, and Shapes
B140/B140M Specification for Copper-Zinc-Lead (Red Brass or Hardware Bronze) Rod, Bar, and Shapes
B283 Specification for Copper and Copper-Alloy Die Forgings (Hot-Pressed)
B371/B371M Specification for Copper-Zinc-Silicon Alloy Rod
B584 Specification for Copper Alloy Sand Castings for General Applications
B967/B967M Specification for Copper-Zinc-Tin-Bismuth Alloy Rod, Bar and Wire
D1600 Terminology for Abbreviated Terms Relating to Plastics
D2122 Test Method for Determining Dimensions of Thermoplastic Pipe and Fittings
E18 Test Methods for Rockwell Hardness of Metallic Materials
F412 Terminology Relating to Plastic Piping Systems
1
This standard is under the jurisdiction of ASTM Committee F17 on Plastic Piping Systems and is the direct responsibility of Subcommittee F17.10 on Fittings.
Current edition approved June 1, 2011Aug. 1, 2012. Published June 2011December 2012. Originally approved in 1997. Last previous edition approved in 2011 as
ε1
F1807 – 11.F1807 – 11a . DOI: 10.1520/F1807-11AE01.10.1520/F1807-12.
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM Standards
volume information, refer to the standard’s Document Summary page on the ASTM website.
*A Summary of Changes section appears at the end of this standard
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1

---------------------- Page: 1 ----------------------
F1807 − 12
F876 Specification for Crosslinked Polyethylene (PEX) Tubing
F877 Specification for Crosslinked Polyethylene (PEX) Hot- and Cold-Water Distribution Systems
F2623 Specification for Polyethylene of Raised Temperature (PE-RT) SDR 9 Tubing
F2769 Specification for Polyethylene
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.