ASTM C1396/C1396M-01e1

NOTICE: This standard has either been superseded and replaced by a new version or discontinued.
Contact ASTM International (www.astm.org) for the latest information.
e1
Designation: C 1396 / C 1396M – 01
Standard Specification for
1
Gypsum Board
This standard is issued under the fixed designation C 1396 / C 1396M; the number immediately following the designation indicates the
year of original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last
reapproval. A superscript epsilon (e) indicates an editorial change since the last revision or reapproval.
1
e NOTE—5.2.2 and 7.2.2 were editorially corrected July 2002.
1. Scope * texture and other decoration. This product is also suitable for
use on interior walls.
1.1 This specification covers the gypsum boards described
1.2 Specifications applicable to all gypsum boards are
in 1.1.1-1.1.9.
located in Section 1-4 and 13-15. Specifications applicable to
NOTE 1—Specifications C 840, C 841, C 844 and C 1280 contain ap-
specific gypsum boards are located in the following sections:
plication procedures for gypsum board.
Section
1.1.1 Gypsum wallboard, designed for use on walls, ceil- Gypsum wallboard, predecorated gypsum board 5
Gypsum backing board, gypsum coreboard, 6
ings, or partitions and that affords a surface suitable to receive
gypsum shaftliner board
decoration.
Water-resistant gypsum backing board 7
1.1.2 Predecorated gypsum board, designed for use as the Exterior gypsum soffit board 8
Gypsum sheathing board 9
finished surfacing for walls, ceilings, or partitions.
Gypsum base for veneer plaster 10
1.1.3 Gypsum backing board, coreboard, and shaftliner
Gypsum lath 11
Gypsum Ceiling Board 12
board, designed for use as a base in multilayer systems or as a
gypsum stud or core in semisolid or solid gypsum board
1.3 The values stated in either inch-pound units or SI
partitions, or in shaft wall assemblies.
(metric) are to be regarded separately as standard. Within the
text, the SI units are shown in brackets. The values stated in
NOTE 2—The terms backing board, coreboard, and shafliner board refer
to different end uses. The term gypsum backing board, as used in this each system shall be used independent of the other. Values
specification, shall include gypsum coreboard and gypsum shafliner board
from the two systems shall not be combined.
unless otherwise stated.
2. Referenced Documents
1.1.4 Water-resistant gypsum backing board, designed pri-
2.1 ASTM Standards:
marily to be used as a base for the application of ceramic or
C 11 Terminology Relating to Gypsum and Related Build-
plastic tile on walls or ceilings. This product is also suitable for
2
ing Materials and Systems
decoration.
C 473 Test Methods for Physical Testing of Gypsum Panel
1.1.5 Exterior gypsum soffıt board, designed for use on
2
Products
exterior soffits and carport ceilings that are completely pro-
C 645 Specification for Nonstructural Steel Framing Mem-
tected from contact with liquid water.
2
bers
1.1.6 Gypsum sheathing board, designed for use as sheath-
C 840 Specification for Application and Finishing of Gyp-
ing on buildings.
2
sum Board
1.1.7 Gypsum base for veneer plaster, designed for use as a
C 841 Specification for Installation of Interior Lathing and
base for the application of gypsum veneer plaster.
2
Furring
1.1.8 Gypsum lath, designed for use as a base for the
C 844 Specification for Application of Gypsum Base to
application of gypsum plaster.
2
Receive Gypsum Veneer Plaster
1.1.9 Gypsum ceiling board, designed for use on interior
C 1264 Specification for Sampling, Inspection, Rejection,
ceilings with framing spaced not more than 24 in. [610 mm] on
Certification, Packaging, Marking, Shipping, Handling,
center and that affords a surface suitable to receive water-based
2
and Storage of Gypsum Board
2
C 1280 Specification for Application of Gypsum Sheathing
1
This specification is under the jurisdiction of ASTM Committee C11 on
Gypsum and Related Building Materials and Systems and is the direct responsibility
of Subcommittee C11.01 on Specifications and Test Methods for Gypsum Products.
Current edition approved June 10, 2001. Published September 2001. Originally
2
Annual Book of ASTM Standards, Vol 04.01.
published as C 1396/C 1396M – 98. Last previous edition C 1396/C 1396M – 00.
*A Summary of Changes section appears at the end of this standard.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.
1

---------------------- Page: 1 ----------------------
NOTICE: This standard has either been superseded and replaced by a new version or discontinued.
Contact ASTM International (www.astm.org) for the latest information.
C 1396 / C 1396M
E 84 Test Method for Surface Burning Characteristics of plied parallel with and on each side of load bearing 2 by 4
3
Building Materials wood studs spaced 16 in. [406 mm] on centers with 6d coated
7
E 96 Test Methods for Water Vapor Transmission
...