ASTM B802/B802M-22

This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
Designation: B802/B802M − 19 B802/B802M − 22
Standard Specification for
Zinc–5 % Aluminum-Mischmetal Alloy-Coated Steel Core
1
Wire for Aluminum Conductors, Steel Reinforced (ACSR)
This standard is issued under the fixed designation B802/B802M; the number immediately following the designation indicates the year
of original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval.
A superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope
1.1 This specification covers round, zinc–5 % aluminum-mischmetal (Zn–5Al–MM) alloy-coated, steel core wire with three
classes of Zn–5Al–MM coating used for mechanical reinforcement in the manufacture of aluminum conductors, steel reinforced
(ACSR).
1.2 This specification covers wire of diameter from 0.0500 to 0.1900 in. or 1.27 to 4.82 mm, inclusive.
1.3 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each
system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the
two systems may result in non-conformance with the standard.
1.4 This international standard was developed in accordance with internationally recognized principles on standardization
established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued
by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
2. Referenced Documents
2.1 The following documents of the issue in effect on date of material purchase form a part of this specification to the extent
referenced herein.
2
2.2 ASTM Standards:
A90/A90M Test Method for Weight [Mass] of Coating on Iron and Steel Articles with Zinc or Zinc-Alloy Coatings
A370 Test Methods and Definitions for Mechanical Testing of Steel Products
A751 Test Methods and Practices for Chemical Analysis of Steel Products
B193 Test Method for Resistivity of Electrical Conductor Materials
B750 Specification for GALFAN (Zinc-5 % Aluminum-Mischmetal) Alloy in Ingot Form for Hot-Dip Coatings
3
E47 Test Methods for Chemical Analysis of Zinc Die-Casting Alloys (Withdrawn 1997)
E1277 Test Method for Analysis of Zinc-5 % Aluminum-Mischmetal Alloys by ICP Emission Spectrometry
E29 Practice for Using Significant Digits in Test Data to Determine Conformance with Specifications
1
This specification is under the jurisdiction of ASTM Committee B01 on Electrical Conductors and is the direct responsibility of Subcommittee B01.05 on Conductors
of Ferrous Metals.
Current edition approved March 1, 2019Oct. 1, 2022. Published April 2019October 2022. Originally approved in 1989. Last previous edition approved in 20162019 as
B802/B802M – 10 (2016).B802/B802M – 19. DOI: 10.1520/B0802_B0802M-19.10.1520/B0802_B0802M-22.
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM Standards
volume information, refer to the standard’s Document Summary page on the ASTM website.
3
The last approved version of this historical standard is referenced on www.astm.org.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1

---------------------- Page: 1 ----------------------
B802/B802M − 22
2.3 Other Standard:
GF-1 Standard Practice for Determination of Cerium and Lanthanum Compositions in Galfan Alloy (5 % Al-0.04 % La-0.04 %
4
Ce-Bal SHG Zn)
3. Terminology
3.1 Abbreviations:
3.1.1 MM—mischmetal.
3.1.2 Zn–5Al–MM—zinc–5 % aluminum mischmetal.
3.2 Definitions:
3.2.1 lot—unless otherwise specified in the contract or order, a lot shall consist of all coils of wire of the same diameter and unit
lengths submitted for inspection at the same time.
3.2.2 Product Code—product code—Definesdefines product coating type, coating class and strength grade. Twograde; two product
codes for product produced to this specification: Class A Zn–5Al–MM Coated = MA2; and Class C Zn–5Al–MM Coated = MC2.
4. Classification
4.1 The wire is furnished in two classes of coating, Class A or Class C, as specified, in conformance with the requirements of
Section 10 and Table 1 or Table 2.
5. Ordering Information
5.1 Orders for material under this specification shall include the following information:
5.1.1 Quantity of each size,
5.1.2 Wire diameter in inches or millimeters (Section 14),
5.1.3 Product Codecode (see paragraphs 3.2.2 and 4.1),
5.1.4 Certification
...

NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation: B802/B802M − 22
Standard Specification for
Zinc–5 % Aluminum-Mischmetal Alloy-Coated Steel Core
1
Wire for Aluminum Conductors, Steel Reinforced (ACSR)
This standard is issued under the fixed designation B802/B802M; the number immediately following the designation indicates the year
of original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval.
A superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope B193 Test Method for Resistivity of Electrical Conductor
Materials
1.1 This specification covers round, zinc–5 % aluminum-
B750 Specification for GALFAN (Zinc-5 % Aluminum-
mischmetal (Zn–5Al–MM) alloy-coated, steel core wire with
Mischmetal) Alloy in Ingot Form for Hot-Dip Coatings
three classes of Zn–5Al–MM coating used for mechanical
E47 Test Methods for Chemical Analysis of Zinc Die-
reinforcement in the manufacture of aluminum conductors,
3
Casting Alloys (Withdrawn 1997)
steel reinforced (ACSR).
E1277 Test Method for Analysis of Zinc-5 % Aluminum-
1.2 This specification covers wire of diameter from 0.0500
Mischmetal Alloys by ICP Emission Spectrometry
to 0.1900 in. or 1.27 to 4.82 mm, inclusive.
E29 Practice for Using Significant Digits in Test Data to
1.3 The values stated in either SI units or inch-pound units Determine Conformance with Specifications
are to be regarded separately as standard. The values stated in 2.3 Other Standard:
each system may not be exact equivalents; therefore, each GF-1 Standard Practice for Determination of Cerium and
Lanthanum Compositions in Galfan Alloy (5 % Al-0.04 %
system shall be used independently of the other. Combining
4
values from the two systems may result in non-conformance La-0.04 % Ce-Bal SHG Zn)
with the standard.
3. Terminology
1.4 This international standard was developed in accor-
3.1 Abbreviations:
dance with internationally recognized principles on standard-
3.1.1 MM—mischmetal.
ization established in the Decision on Principles for the
Development of International Standards, Guides and Recom- 3.1.2 Zn–5Al–MM—zinc–5 % aluminum mischmetal.
mendations issued by the World Trade Organization Technical
3.2 Definitions:
Barriers to Trade (TBT) Committee.
3.2.1 lot—unless otherwise specified in the contract or
order, a lot shall consist of all coils of wire of the same
2. Referenced Documents
diameter and unit lengths submitted for inspection at the same
2.1 The following documents of the issue in effect on date
time.
of material purchase form a part of this specification to the
3.2.2 product code—defines product coating type, coating
extent referenced herein.
class and strength grade; two product codes for product
2
2.2 ASTM Standards:
produced to this specification: Class A Zn–5Al–MM Coated =
A90/A90M Test Method for Weight [Mass] of Coating on
MA2; and Class C Zn–5Al–MM Coated = MC2.
Iron and Steel Articles with Zinc or Zinc-Alloy Coatings
A370 Test Methods and Definitions for Mechanical Testing 4. Classification
of Steel Products
4.1 The wire is furnished in two classes of coating, Class A
A751 Test Methods and Practices for Chemical Analysis of
or Class C, as specified, in conformance with the requirements
Steel Products
of Section 10 and Table 1 or Table 2.
1
5. Ordering Information
This specification is under the jurisdiction of ASTM Committee B01 on
Electrical Conductors and is the direct responsibility of Subcommittee B01.05 on
5.1 Orders for material under this specification shall include
Conductors of Ferrous Metals.
the following information:
Current edition approved Oct. 1, 2022. Published October 2022. Originally
approved in 1989. Last previous edition approved in 2019 as B802/B802M – 19.
DOI: 10.1520/B0802_B0802M-22.
2 3
For referenced ASTM standards, visit the ASTM website, www.astm.org, or The last approved version of this historical standard is referenced on
contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM www.astm.org.
4
Standards volume information, refer to the standard’s Document Summary page on Available from International Lead Zinc Research Organization (ILZRO), 1822
the ASTM website. NC Highway 54 East, Suite 120, Durham NC 27713, http://www.ilzro.org.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1

---------------------- Page: 1 ----------------------
B802/B802M − 22
TABLE 1 Zn-5Al-MM Alloy Coating
7.3.2 Method of Analysis—The determination of chemical
Area Density of Coating, min, oz/ composition shall be made in accordance with suitable chemi-
Specified Diameter of Coated Wire, 2
ft of Uncoated Wire Surface
cal (Test Methods E47 for Tin), ICP argon plasma spectromet-
in.
Class A Class C
ric (Practice E1277), or other methods. In case of dispu
...