ASTM F467-06ae1

This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
´1
Designation:F467–06a Designation: F 467 – 06a
Standard Specification for
1
Nonferrous Nuts for General Use
This standard is issued under the fixed designation F 467; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
This standard has been approved for use by agencies of the Department of Defense.
1
´ NOTE—Table 1 Nickel and Nickel-Base Alloys and Table 2 were editorially corrected in February 2008.
1. Scope*
1.1 This specification covers the requirements for commercial wrought nonferrous nuts 0.250 to 1.500 in. inclusive in diameter
in a number of alloys in common use and intended for general service applications.
1.2 Applicable bolts, cap screws, and studs for use with nuts covered by this specification are covered by Specification F 468.
NOTE 1—A complete metric companion to Specification F 467 has been developed—F 467M; therefore no metric equivalents are presented in this
specification.
2. Referenced Documents
2
2.1 ASTM Standards:
B 154 Test Method for Mercurous Nitrate Test for Copper Alloys
B574 Specification for Low-Carbon Nickel-Chromium-Molybdenum, Low-Carbon Nickel-Molybdenum-Chromium-
Tantalum, Low-Carbon Nickel-Chromium-Molybdenum-Copper, and Low-Carbon Nickel-Chromium-Molybdenum-Tungsten
Alloy Rod
D 3951 Practice for Commercial Packaging
E18 Test Methods for Rockwell Hardness of Metallic Materials
E29 Practice for Using Significant Digits in Test Data to Determine Conformance with Specifications
E34 Test Methods for Chemical Analysis of Aluminum and Aluminum-Base Alloys
3
E38 Methods for Chemical Analysis of Nickel-Chromium and Nickel-Chromium-Iron Alloys
E53 Test Method for Determination of Copper in Unalloyed Copper by Gravimetry
E54 Test Methods for Chemical Analysis of Special Brasses and Bronzes
E55 Practice for Sampling Wrought Nonferrous Metals and Alloys for Determination of Chemical Composition
E62 Test Methods for Chemical Analysis of Copper and Copper Alloys (Photometric Methods)
E75 Test Methods for Chemical Analysis of Copper-Nickel and Copper-Nickel-Zinc Alloys
E76 Test Methods for Chemical Analysis of Nickel-Copper Alloys
E92 Test Method for Vickers Hardness of Metallic Materials
0
E 101 Test Method for Spectrographic Analysis of Aluminum and Aluminum Alloys by the Point-To-Plane Technique
E 120 Test Methods for Chemical Analysis of Titanium and Titanium Alloys
E 165 Test Method for Liquid Penetrant Examination
E 227 Test Method for Optical Emission Spectrometric Analysis of Aluminum and Aluminum Alloys by the Point-to-Plane
Technique
E 354 Test Methods for Chemical Analysis of High-Temperature, Electrical, Magnetic, and Other Similar Iron, Nickel, and
Cobalt Alloys
E 478 Test Methods for Chemical Analysis of Copper Alloys
E 1409 Test Method for Determination of Oxygen and Nitrogen in Titanium and Titanium Alloys by the Inert Gas Fusion
Technique
F 468 Specification for Nonferrous Bolts, Hex Cap Screws, and Studs for General Use
1
This specification is under the jurisdiction of ASTM Committee F16 on Fasteners and is the direct responsibility of Subcommittee F16.04 on Nonferrous Fasteners .
Current edition approved Aug. 1, 2006. Published August 2006. Originally approved in 1976. Last previous edition approved in 2006 as F 467 – 06.
2
For referencedASTM standards, visit theASTM website, www.astm.org, or contactASTM Customer Service at service@astm.org. For Annual Book of ASTM Standards
volume information, refer to the standard’s Document Summary page on the ASTM website.
3
Withdrawn.
*A Summary of Changes section appears at the end of this standard.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.
1

---------------------- Page: 1 ----------------------
´1
F 467 – 06a
F 606 Test Methods for Determining the Mechanical Properties of Externally and Internally Threaded Fasteners, Washers,
Direct Tension Indicators, and Rivets
F 1470 Practice for Fastener Sampling for Specified Mechanical Properties and Performance Inspection
4
2.2 ASME Standards:
B 1.1 Unified Inch Screw Threads (UN and UNR Thread Form)
B 18.2.2 Square and Hex Nuts
3. Ordering Information
3.1 Orders for nuts under this specification shall include the following information:
3.1.1 Quantity (number of pieces of each item and size);
3.1.2 Name of item;
3.1.3 Size (diameter and thre
...

This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
e1
Designation:F467–06 Designation: F 467 – 06a
Standard Specification for
1
Nonferrous Nuts for General Use
This standard is issued under the fixed designation F 467; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (e) indicates an editorial change since the last revision or reapproval.
This standard has been approved for use by agencies of the Department of Defense.
1
e NOTE—Table 1 Nickel and Nickel-Base Alloys and Table 2 were editorially corrected in February 2008.
1. Scope*
1.1 This specification covers the requirements for commercial wrought nonferrous nuts 0.250 to 1.500 in. inclusive in diameter
in a number of alloys in common use and intended for general service applications.
1.2 Applicable bolts, cap screws, and studs for use with nuts covered by this specification are covered by Specification F 468.
NOTE 1—A complete metric companion to Specification F 467 has been developed—F 467M; therefore no metric equivalents are presented in this
specification.
2. Referenced Documents
2
2.1 ASTM Standards:
B 154 Test Method for Mercurous Nitrate Test for Copper Alloys
B 574 Specification for Low-Carbon Nickel-Chromium-Molybdenum, Low-Carbon Nickel-Molybdenum-Chromium-
Tantalum, Low-Carbon Nickel-Chromium-Molybdenum-Copper, and Low-Carbon Nickel-Chromium-Molybdenum-Tungsten
Alloy Rod
D 3951 Practice for Commercial Packaging
E 18 Test Methods for Rockwell Hardness of Metallic Materials
E 29 Practice for Using Significant Digits in Test Data to Determine Conformance with Specifications
E 34 Test Methods for Chemical Analysis of Aluminum and Aluminum-Base Alloys
3
E 38 Methods for Chemical Analysis of Nickel-Chromium and Nickel-Chromium-Iron Alloys
E 53 Test Method for Determination of Copper in Unalloyed Copper by Gravimetry
E 54 Test Methods for Chemical Analysis of Special Brasses and Bronzes
E 55 Practice for Sampling Wrought Nonferrous Metals and Alloys for Determination of Chemical Composition
E 62 Test Methods for Chemical Analysis of Copper and Copper Alloys (Photometric Methods)
E 75 Test Methods for Chemical Analysis of Copper-Nickel and Copper-Nickel-Zinc Alloys
E 76 Test Methods for Chemical Analysis of Nickel-Copper Alloys
E 92 Test Method for Vickers Hardness of Metallic Materials
0
E 101 Test Method for Spectrographic Analysis of Aluminum and Aluminum Alloys by the Point-To-Plane Technique
E 120 Test Methods for Chemical Analysis of Titanium and Titanium Alloys
E 165 Test Method for Liquid Penetrant Examination
E 227 Test Method for Optical Emission Spectrometric Analysis of Aluminum and Aluminum Alloys by the Point-to-Plane
Technique
E 354 Test Methods for Chemical Analysis of High-Temperature, Electrical, Magnetic, and Other Similar Iron, Nickel, and
Cobalt Alloys
E 478 Test Methods for Chemical Analysis of Copper Alloys
E 1409 Test Method for Determination of Oxygen and Nitrogen in Titanium and Titanium Alloys by the Inert Gas Fusion
Technique
F 468 Specification for Nonferrous Bolts, Hex Cap Screws, and Studs for General Use
1
This specification is under the jurisdiction of ASTM Committee F16 on Fasteners and is the direct responsibility of Subcommittee F16.04 on Nonferrous Fasteners .
Current edition approved MayAug. 1, 2006. Published MayAugust 2006. Originally approved in 1976. Last previous edition approved in 20052006 as F 467 – 056.
2
For referencedASTM standards, visit theASTM website, www.astm.org, or contactASTM Customer Service at service@astm.org. For Annual Book of ASTM Standards
volume information, refer to the standard’s Document Summary page on the ASTM website.
3
Withdrawn.
*A Summary of Changes section appears at the end of this standard.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.
1

---------------------- Page: 1 ----------------------
e1
F 467 – 06a
F 606 Test Methods for Determining the Mechanical Properties of Externally and Internally Threaded Fasteners, Washers,
Direct Tension Indicators, and Rivets
F 1470 Guide for Fastener Sampling for Specified Mechanical Properties and Performance Inspection
4
2.2 ASME Standards:
B 1.1 Unified Inch Screw Threads (UN and UNR Thread Form)
B 18.2.2 Square and Hex Nuts
3. Ordering Information
3.1 Orders for nuts under this specification shall include the following information:
3.1.1 Quantity (number of pieces of each item and size);
3.1.2 Name of item;
3.1.3 Size
...