ASTM F2080-15a
(Specification)Standard Specification for Cold-Expansion Fittings with Metal Compression-Sleeves for Crosslinked Polyethylene (PEX) Pipe
Standard Specification for Cold-Expansion Fittings with Metal Compression-Sleeves for Crosslinked Polyethylene (PEX) Pipe
ABSTRACT
This specification covers cold-expansion fittings using metal compression-sleeves for use with cross-linked polyethylene (PEX) plastic pipe. These cold-expansion fittings and metal compression-sleeves are intended for use in residential and commercial, hot and cold, potable water distribution systems, as well as sealed central heating, including under-floor heating systems, with continuous operation. Cold-expansion fittings shall be made from one of the following materials: machined brass; machined stainless steel; machined carbon steel; forged brass; or cast copper alloys. Metal compression-sleeves shall be made from one of the following materials: machined brass; machined stainless steel; or plating. Dimension measurements shall be made in accordance with the specified requirements.
SCOPE
1.1 This specification covers cold-expansion fittings using metal compression-sleeves for use with crosslinked polyethylene (PEX) plastic pipe in accordance with Specification F876 in 3/8-in., 1/2-in., 5/8-in., 3/4-in., 1-in., 11/4-in., 11/2-in., and 2 in. nominal diameters, whereby the PEX pipe is cold-expanded before fitting assembly. The components covered by this specification are intended for use in residential and commercial, hot and cold, potable water distribution systems or other applications such as municipal water service lines, radiant panel heating systems, hydronic baseboard heating systems, snow and ice melting systems, geothermal underground pipe systems and building services pipe with continuous operation at pressures up to and including 100 psi (690 kPa), and at temperatures up to and including 180°F (82°C).
1.2 Included in this specification are the requirements for materials, workmanship, dimensions, and markings to be used on the fittings and compression-sleeves. Performance requirements are as referenced in Specification F877.
1.3 The values stated in inch-pound units are to be regarded as the standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.
1.4 The following precautionary caveat pertains only to the test method portion, Section 10, of this specification. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
General Information
Relations
Buy Standard
Standards Content (Sample)
NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation:F2080 −15a
StandardSpecification for
Cold-Expansion Fittings with Metal Compression-Sleeves
1
for Crosslinked Polyethylene (PEX) Pipe
This standard is issued under the fixed designation F2080; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope* 2. Referenced Documents
2
2.1 ASTM Standards:
1.1 This specification covers cold-expansion fittings using
A108 Specification for Steel Bar, Carbon and Alloy, Cold-
metal compression-sleeves for use with crosslinked polyethyl-
Finished
ene (PEX) plastic pipe in accordance with Specification F876
A269 Specification for Seamless and Welded Austenitic
3 1 5 3 1 1
in ⁄8-in., ⁄2-in., ⁄8-in., ⁄4-in., 1-in., 1 ⁄4-in., 1 ⁄2-in., and 2 in.
Stainless Steel Tubing for General Service
nominal diameters, whereby the PEX pipe is cold-expanded
A276 Specification for Stainless Steel Bars and Shapes
before fitting assembly. The components covered by this
A312/A312M Specification for Seamless, Welded, and
specification are intended for use in residential and
Heavily Cold Worked Austenitic Stainless Steel Pipes
commercial,hotandcold,potablewaterdistributionsystemsor
A519 Specification for Seamless Carbon and Alloy Steel
other applications such as municipal water service lines,
Mechanical Tubing
radiant panel heating systems, hydronic baseboard heating
B16/B16M Specification for Free-Cutting Brass Rod, Bar
systems, snow and ice melting systems, geothermal under-
and Shapes for Use in Screw Machines
ground pipe systems and building services pipe with continu-
B62 Specification for Composition Bronze or Ounce Metal
ous operation at pressures up to and including 100 psi (690
Castings
kPa), and at temperatures up to and including 180°F (82°C).
B140/B140M Specification for Copper-Zinc-Lead (Red
Brass or Hardware Bronze) Rod, Bar, and Shapes
1.2 Included in this specification are the requirements for
B283 Specification for Copper and Copper-Alloy Die Forg-
materials, workmanship, dimensions, and markings to be used
ings (Hot-Pressed)
on the fittings and compression-sleeves. Performance require-
B371/B371M Specification for Copper-Zinc-Silicon Alloy
ments are as referenced in Specification F877.
Rod
B584 Specification for Copper Alloy Sand Castings for
1.3 The values stated in inch-pound units are to be regarded
General Applications
asthestandard.Thevaluesgiveninparenthesesaremathemati-
B689 Specification for Electroplated Engineering Nickel
cal conversions to SI units that are provided for information
Coatings
only and are not considered standard.
B851 Specification for Automated Controlled Shot Peening
1.4 The following precautionary caveat pertains only to the
of Metallic Articles Prior to Nickel, Autocatalytic Nickel,
test method portion, Section 10, of this specification. This
or Chromium Plating, or as Final Finish
standard does not purport to address all of the safety concerns,
D1600 Terminology forAbbreviatedTerms Relating to Plas-
if any, associated with its use. It is the responsibility of the user
tics
of this standard to establish appropriate safety and health
D2122 Test Method for Determining Dimensions of Ther-
practices and determine the applicability of regulatory limita-
moplastic Pipe and Fittings
tions prior to use.
F412 Terminology Relating to Plastic Piping Systems
F876 SpecificationforCrosslinkedPolyethylene(PEX)Tub-
ing
F877 SpecificationforCrosslinkedPolyethylene(PEX)Hot-
and Cold-Water Distribution Systems
1
This specification is under the jurisdiction ofASTM Committee F17 on Plastic
2
Piping Systems and is the direct responsibility of Subcommittee F17.10 on Fittings. For referenced ASTM standards, visit the ASTM website, www.astm.org, or
Current edition approved Nov. 1, 2015. Published December 2015. Originally contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM
approved in 2001. Last previous edition approved in 2015 as F2080 –15. DOI: Standards volume information, refer to the standard’s Document Summary page on
10.1520/F2080-15A. the ASTM website.
*A Summary of Changes section appears at the end of this standard
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1
---------------------- Page: 1 ----------------------
F2080−15a
2.2 ASME Standards: Specification B283, CopperAlloy UNS C89844, CopperAlloy
3
B1.20.1 Pipe Threads General Purpose (Inch) UNS No. C27450 or Standard EN 12164, Copper Alloy
B16.18 Cast Copper Alloy Solder Joint Pressure Fittings CW614N.
3
(Inch)
5.1.2 Machined Stainless Steel—Machined stainless steel
B16.22 WroughtCopperAlloySolderJointPressureFittings
c
...
This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
Designation: F2080 − 15 F2080 − 15a
Standard Specification for
Cold-Expansion Fittings Withwith Metal Compression-
Sleeves for Cross-LinkedCrosslinked Polyethylene (PEX)
1
Pipe
This standard is issued under the fixed designation F2080; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope*
1.1 This specification covers cold-expansion fittings using metal compression-sleeves for use with cross-linkedcrosslinked
3 1 5 3 1 1
polyethylene (PEX) plastic pipe in accordance with Specification F876 in ⁄8-in., ⁄2-in., ⁄8-in., ⁄4-in., 1-in., 1 ⁄4-in., 1 ⁄2-in., and
2 in. nominal diameters, whereby the PEX pipe is cold-expanded before fitting assembly. These cold-expansion fittings and metal
compression-sleevesThe components covered by this specification are intended for use in residential and commercial, hot and cold,
potable water distribution systems, as well as sealed central heating, including under-floor heating systems, systems or other
applications such as municipal water service lines, radiant panel heating systems, hydronic baseboard heating systems, snow and
ice melting systems, geothermal underground pipe systems and building services pipe with continuous operation at pressures up
to and including 100 psi (690 kPa), and at temperatures up to and including 180°F (82°C).
1.2 Included in this specification are the requirements for materials, workmanship, dimensions, and markings to be used on the
fittings and compression-sleeves. Performance requirements are as referenced in Specification F877.
1.3 The values stated in inch-pound units are to be regarded as the standard. The values given in parentheses are mathematical
conversions to SI units that are provided for information only and are not considered standard.
1.4 The following precautionary caveat pertains only to the test method portion, Section 10, of this specification.This standard
does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this
standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
2. Referenced Documents
2
2.1 ASTM Standards:
A108 Specification for Steel Bar, Carbon and Alloy, Cold-Finished
A269 Specification for Seamless and Welded Austenitic Stainless Steel Tubing for General Service
A276 Specification for Stainless Steel Bars and Shapes
A312/A312M Specification for Seamless, Welded, and Heavily Cold Worked Austenitic Stainless Steel Pipes
A519 Specification for Seamless Carbon and Alloy Steel Mechanical Tubing
B16/B16M Specification for Free-Cutting Brass Rod, Bar and Shapes for Use in Screw Machines
B62 Specification for Composition Bronze or Ounce Metal Castings
B140/B140M Specification for Copper-Zinc-Lead (Red Brass or Hardware Bronze) Rod, Bar, and Shapes
B283 Specification for Copper and Copper-Alloy Die Forgings (Hot-Pressed)
B371/B371M Specification for Copper-Zinc-Silicon Alloy Rod
B584 Specification for Copper Alloy Sand Castings for General Applications
B689 Specification for Electroplated Engineering Nickel Coatings
B851 Specification for Automated Controlled Shot Peening of Metallic Articles Prior to Nickel, Autocatalytic Nickel, or
Chromium Plating, or as Final Finish
D1600 Terminology for Abbreviated Terms Relating to Plastics
D2122 Test Method for Determining Dimensions of Thermoplastic Pipe and Fittings
1
This specification is under the jurisdiction of ASTM Committee F17 on Plastic Piping Systems and is the direct responsibility of Subcommittee F17.10 on Fittings.
Current edition approved Aug. 1, 2015Nov. 1, 2015. Published August 2015December 2015. Originally approved in 2001. Last previous edition approved in 20122015
ε1
as F2080 –12 –15. . DOI: 10.1520/F2080-15.10.1520/F2080-15A.
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM Standards
volume information, refer to the standard’s Document Summary page on the ASTM website.
*A Summary of Changes section appears at the end of this standard
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1
---------------------- Page: 1 ----------------------
F2080 − 15a
F412 Terminology Relating to Plasti
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.