ASTM B411/B411M-08
(Specification)Standard Specification for Copper-Nickel-Silicon Alloy Rod and Bar
Standard Specification for Copper-Nickel-Silicon Alloy Rod and Bar
SCOPE
1.1 This specification establishes the requirements for copper-nickel-silicon alloy rod and bar produced from Copper Alloy UNS No. C64700 in straight lengths.
1.2 Units—The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.
General Information
Relations
Buy Standard
Standards Content (Sample)
NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation:B411/B411M −08
StandardSpecification for
1
Copper-Nickel-Silicon Alloy Rod and Bar
This standard is issued under the fixed designation B411/B411M; the number immediately following the designation indicates the year
of original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval.
A superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
This standard has been approved for use by agencies of the Department of Defense.
1. Scope* 3.1.1 Terminology,
3.1.2 Workmanship, Finish, and Appearance,
1.1 This specification establishes the requirements for
3.1.3 Sampling,
copper-nickel-silicon alloy rod and bar produced from Copper
3.1.4 Number of Tests and Retests,
Alloy UNS No. C64700 in straight lengths.
3.1.5 Specimen Preparation,
1.2 Units—The values stated in either SI units or inch-
3.1.6 Test Methods,
pound units are to be regarded separately as standard. The
3.1.7 Significance of Numerical Limits,
values stated in each system may not be exact equivalents;
3.1.8 Inspection,
therefore, each system shall be used independently of the other.
3.1.9 Rejection and Rehearing,
Combining values from the two systems may result in non-
3.1.10 Certification,
conformance with the standard.
3.1.11 Mill Test Report,
3.1.12 Packaging and Package Marking, and
2. Referenced Documents
3.1.13 Supplementary Requirements.
2
2.1 ASTM Standards:
3.2 In addition, when a section with a title identical to that
B193 Test Method for Resistivity of Electrical Conductor
referenced in 3.1 appears in this specification, it contains
Materials
additional requirements which supplement those appearing in
B249/B249M Specification for General Requirements for
Specification B249/B249M.
Wrought Copper and Copper-Alloy Rod, Bar, Shapes and
Forgings
4. Terminology
B601 Classification forTemper Designations for Copper and
4.1 For the definition of terms related to copper and copper
Copper Alloys—Wrought and Cast
alloys, refer to Terminology B846.
B846 Terminology for Copper and Copper Alloys
E8 Test Methods for Tension Testing of Metallic Materials
5. Ordering Information
E8M Test Methods forTensionTesting of Metallic Materials
3
5.1 Include the following information when placing orders
[Metric] (Withdrawn 2008)
for product under this specification, as applicable:
E54 Test Methods for ChemicalAnalysis of Special Brasses
3
5.1.1 ASTM designation and year of issue (for example,
and Bronzes (Withdrawn 2002)
B411/B411M – 06),
E478 Test Methods for ChemicalAnalysis of CopperAlloys
5.1.2 Copper alloy UNS No. designation,
3. General Requirements
5.1.3 Temper,
5.1.4 Product form (cross section such as round, hexagonal,
3.1 The following sections of Specification B249/B249M
square, and so forth),
constitute a part of this specification:
5.1.5 Dimensions (diameter or distance between parallel
surfaces, width, thickness),
1
This specification is under the jurisdiction ofASTM Committee B05 on Copper
5.1.6 Edge contours,
and CopperAlloys and is the direct responsibility of Subcommittee B05.02 on Rod,
5.1.7 Length, nominal,
Bar, Wire, Shapes and Forgings.
5.1.8 Quantity; total weight, length, or number of pieces for
Current edition approved Oct. 1, 2008. Published November 2008. Originally
approved in 1965. Last previous edition approved in 2006 as B411/B411M – 06.
each form and size, and
DOI: 10.1520/B0411_B0411M-08.
5.1.9 When product is purchased for agencies of the U.S.
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or
government.
contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM
Standards volume information, refer to the standard’s Document Summary page on
5.2 The following options are available and should be
the ASTM website.
3
specified at the time of placing the order, when required:
The last approved version of this historical standard is referenced on
www.astm.org. 5.2.1 Certification (Specification B249/B249M), and
*A Summary of Changes section appears at the end of this standard
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1
---------------------- Page: 1 ----------------------
B411/B411M−08
5.2.2 Mill test report (Specification B249/B249M). 10.1.1 Product furnished in the precipitation-hardenedTF00
temper, as normally supplied, shall conform to the tensile
6. Material and Manufacture requirements prescribed in Table 2, when tested in accordance
with Test Methods E8 or E8M.
6.1 Material—The material of manufacture shall be cast
10.1.2 Product furnished in TB00 (solution heat-treated)
billets or ingots of Copper Alloy UNS No. C64700 of such
temper or TD00 through TD02 (solution heat-treated and
soundness and structure that they are suitable for processing
cold-worked) inclusi
...
This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
Designation:B411/B411M–06 Designation: B 411/B 411M – 08
Standard Specification for
1
Copper-Nickel-Silicon Alloy Rod and Bar
This standard is issued under the fixed designation B 411/B 411M; the number immediately following the designation indicates the year
of original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval.
A superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
This standard has been approved for use by agencies of the Department of Defense.
1. Scope*
1.1 Thisspecificationestablishestherequirementsforcopper-nickel-siliconalloyrodandbarproducedfromCopperAlloyUNS
No. C64700 in straight lengths.
1.2 Units—The values stated in either inch-pound SI units or in SI inch-pound units are to be regarded separately as standard.
Within the text, the SI units are shown in brackets. The values stated in each system may not be exact equivalents; therefore, each
system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the
standard.
2. Referenced Documents
2
2.1 ASTM Standards:
B 193 Test Method for Resistivity of Electrical Conductor Materials
B 249/B 249M Specification for General Requirements for Wrought Copper and Copper-Alloy Rod, Bar, Shapes and Forgings
B 601 Classification for Temper Designations for Copper and Copper AlloysWrought and Cast
B 846 Terminology for Copper and Copper Alloys
E 8 Test Methods for Tension Testing of Metallic Materials
E 8M Test Methods for Tension Testing of Metallic Materials [Metric]
E 54 Test Methods for Chemical Analysis of Special Brasses and Bronzes
E 478 Test Methods for Chemical Analysis of Copper Alloys
3. General Requirements
3.1 The following sections of Specification B 249/B 249M constitute a part of this specification:
3.1.1 Terminology,
3.1.2 Workmanship, Finish, and Appearance,
3.1.3 Sampling,
3.1.4 Number of Tests and Retests,
3.1.5 Specimen Preparation,
3.1.6 Test Methods,
3.1.7 Significance of Numerical Limits,
3.1.8 Inspection,
3.1.9 Rejection and Rehearing,
3.1.10 Certification,
3.1.11 Mill Test Report,
3.1.12 Packaging and Package Marking, and
3.1.13 Supplementary Requirements.
3.2 In addition, when a section with a title identical to that referenced in 3.1 appears in this specification, it contains additional
requirements which supplement those appearing in Specification B 249/B 249M.
4. Terminology
4.1 For the definition of terms related to copper and copper alloys, refer to Terminology B 846.
1
This specification is under the jurisdiction ofASTM Committee B05 on Copper and CopperAlloys and is the direct responsibility of Subcommittee B05.02 on Rod, Bar,
Wire, Shapes,Shapes and Forgings.
Current edition approved Oct. 1, 2006.2008. Published October 2006.November 2008. Originally approved in 1965. Last previous edition approved in 20012006 as
B 411/B 411M – 016.
2
For referencedASTM standards, visit theASTM website, www.astm.org, or contactASTM Customer Service at service@astm.org. ForAnnualBookofASTMStandards
volume information, refer to the standard’s Document Summary page on the ASTM website.
*ASummary of Changes section appears at the end of this standard.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.
1
---------------------- Page: 1 ----------------------
B 411/B 411M – 08
5. Ordering Information
5.1 Include the following information when placing orders for product under this specification, as applicable:
5.1.1 ASTM designation and year of issue (for example, B 411/B 411M – 06),
5.1.2 Copper alloy UNS No. designation,
5.1.3 Temper,
5.1.4 Product form (cross section such as round, hexagonal, square, and so forth),
5.1.5 Dimensions (diameter or distance between parallel surfaces, width, thickness),
5.1.6 Edge contours,
5.1.7 Length, nominal,
5.1.8 Quantity; total weight, length, or number of pieces for each form and size, and
5.1.9 When product is purchased for agencies of the U.S. government.
5.2 The following options are available and should be specified at the time of placing the order, when required:
5.2.1 Certification (Specification B 249/B 249M), and
5.2.2 Mill test report (Specification B 249/B 249M).
6. Material and Manufacture
6.1 Material—The material of manufacture shall be cast billets or ingots of CopperAlloy UNS No. C64700 of such soundness
and structure that they are suitable for processing into the products prescribed herein.
6.2 Manufacture—The product shall be manu
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.