ASTM D5773-21
(Test Method)Standard Test Method for Cloud Point of Petroleum Products and Liquid Fuels (Constant Cooling Rate Method)
Standard Test Method for Cloud Point of Petroleum Products and Liquid Fuels (Constant Cooling Rate Method)
SIGNIFICANCE AND USE
5.1 The cloud point of petroleum products and biodiesel fuels is an index of the lowest temperature of their utility for certain applications. Wax crystals of sufficient quantity can plug filters used in some fuel systems.
5.2 Petroleum blending operations require a precise measurement of the cloud point.
5.3 This test method can determine the temperature of the test specimen at which wax crystals have formed sufficiently to be observed as a cloud with a resolution of 0.1 °C.
5.4 This test method provides results that are equivalent to Test Method D2500.
Note 1: This is based on the Test Method D2500 equivalent cloud point in which the 0.1 °C result is rounded to the next lower integer.
5.5 This test method determines the cloud point in a shorter period of time than Test Method D2500.
Note 2: In cases of samples with cloud points near ambient temperatures, time savings may not be realized.
5.6 This test method eliminates most of the operator time required of Test Method D2500.
5.7 This test method does not require the use of a mechanical refrigeration apparatus.
Note 3: In certain cases of high ambient temperature, a source of cooling water may be required to measure low-temperature cloud points (see 7.1).
SCOPE
1.1 This test method covers the determination of the cloud point of petroleum products and biodiesel fuels that are transparent in layers 40 mm in thickness by an automatic instrument using a constant cooling rate.
1.2 This test method covers the range of temperatures from −60 °C to +49 °C with temperature resolution of 0.1 °C, however, the range of temperatures included in the 1997 interlaboratory cooperative test program only covered the temperature range of –56 °C to +34 °C.
1.3 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
General Information
Buy Standard
Standards Content (Sample)
This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the
Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
Designation: D5773 − 21
Designation: IP 446/09
Standard Test Method for
Cloud Point of Petroleum Products and Liquid Fuels
1
(Constant Cooling Rate Method)
This standard is issued under the fixed designation D5773; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision.Anumber in parentheses indicates the year of last reapproval.A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
INTRODUCTION
This test method describes an alternative procedure for the determination of cloud point of
petroleum productsTest MethodD2500/IP219 using an automatic apparatus.The temperature results
from this test method have been found to be equivalent to Test Method D2500/IP 219. When
specification requires Test Method D2500/IP 219, do not substitute this test method or any other
method without obtaining comparative data and agreement from the specifier.
1. Scope* 2. Referenced Documents
2
2.1 ASTM Standards:
1.1 This test method covers the determination of the cloud
D2500Test Method for Cloud Point of Petroleum Products
point of petroleum products and biodiesel fuels that are
and Liquid Fuels
transparent in layers 40mm in thickness by an automatic
D4057Practice for Manual Sampling of Petroleum and
instrument using a constant cooling rate.
Petroleum Products
1.2 This test method covers the range of temperatures from
D4177Practice for Automatic Sampling of Petroleum and
−60°C to +49°C with temperature resolution of 0.1°C,
Petroleum Products
however, the range of temperatures included in the 1997
D6751Specification for Biodiesel Fuel Blend Stock (B100)
interlaboratory cooperative test program only covered the
for Middle Distillate Fuels
temperature range of –56°C to +34°C.
3
2.2 Energy Institute Standard:
1.3 The values stated in SI units are to be regarded as
IP 219Test Method for Cloud Point of Petroleum Products
standard. No other units of measurement are included in this
IP 446Determination of the Cloud Point of Petroleum
standard.
Products—Automatic Constant Cooling Rate Method
1.4 This standard does not purport to address all of the
3. Terminology
safety concerns, if any, associated with its use. It is the
responsibility of the user of this standard to establish appro-
3.1 Definitions:
priate safety, health, and environmental practices and deter-
3.1.1 biodiesel, n—fuel comprised of mono-alkyl esters of
mine the applicability of regulatory limitations prior to use.
long chain fatty acids derived from vegetable oils or animal
1.5 This international standard was developed in accor-
fats, designated B100.
dance with internationally recognized principles on standard- 3.1.1.1 Discussion—Biodiesel is typically produced by a
ization established in the Decision on Principles for the
reactionofavegetableoiloranimalfatwithanalcoholsuchas
Development of International Standards, Guides and Recom-
methanol or ethanol in the presence of a catalyst to yield
mendations issued by the World Trade Organization Technical
mono-alkylestersandglycerin,whichisremoved.Thefinished
Barriers to Trade (TBT) Committee.
biodiesel derives approximately 10% of its mass from the
1 2
This test method is under the jurisdiction of ASTM Committee D02 on For referenced ASTM standards, visit the ASTM website, www.astm.org, or
Petroleum Products, Liquid Fuels, and Lubricants and is the direct responsibility of contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM
Subcommittee D02.07 on Flow Properties. Standards volume information, refer to the standard’s Document Summary page on
Current edition approved Jan. 1, 2021. Published January 2021. Originally the ASTM website.
3
approved in 1995. Last previous edition approved in 2020 as D5773–20. DOI: Available from Energy Institute, 61 New Cavendish St., London, WIG 7AR,
10.1520/D5773-21. U.K., http://www.energyinst.org.uk.
*A Summary of Changes section appears at the end of this standard
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1
---------------------- Page: 1 ----------------------
D5773 − 21
reacted alcohol. The alcohol used in the reaction may or may figured in such a way that it will transfer heat to or away from
not come from renewable resources. a test specimen dependent on the direction of electric current
applied to the device.
3.1.2 biodiesel blend (BXX), n—a homogeneous mixture of
hydrocarbon oils and mono-alkyl esters of long chain fatty
3.2.4 D2500/IP 219 equivalent cloud point, n—thetempera-
acids.
ture of a specimen, in integers, calculated by rounding the
3.1.2.1 Discuss
...
This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
Designation: D5773 − 20 D5773 − 21
Designation: IP 446/09
Standard Test Method for
Cloud Point of Petroleum Products and Liquid Fuels
1
(Constant Cooling Rate Method)
This standard is issued under the fixed designation D5773; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
INTRODUCTION
This test method describes an alternative procedure for the determination of cloud point of
petroleum products Test Method D2500/IP 219 using an automatic apparatus. The temperature results
from this test method have been found to be equivalent to Test Method D2500/IP 219. When
specification requires Test Method D2500/IP 219, do not substitute this test method or any other
method without obtaining comparative data and agreement from the specifier.
1. Scope*
1.1 This test method covers the determination of the cloud point of petroleum products and biodiesel fuels that are transparent in
layers 40 mm in thickness by an automatic instrument using a constant cooling rate.
1.2 This test method covers the range of temperatures from −60 °C to +49 °C with temperature resolution of 0.1 °C, however, the
range of temperatures included in the 1997 interlaboratory cooperative test program only covered the temperature range of –56 °C
to +34 °C.
1.3 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility
of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of
regulatory limitations prior to use.
1.5 This international standard was developed in accordance with internationally recognized principles on standardization
established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued
by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
2. Referenced Documents
2
2.1 ASTM Standards:
D2500 Test Method for Cloud Point of Petroleum Products and Liquid Fuels
1
This test method is under the jurisdiction of ASTM Committee D02 on Petroleum Products, Liquid Fuels, and Lubricants and is the direct responsibility of Subcommittee
D02.07 on Flow Properties.
Current edition approved June 1, 2020Jan. 1, 2021. Published June 2020January 2021. Originally approved in 1995. Last previous edition approved in 20172020 as
ɛ1
D5773 – 17D5773 – 20. . DOI: 10.1520/D5773-20.10.1520/D5773-21.
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM Standards
volume information, refer to the standard’s Document Summary page on the ASTM website.
*A Summary of Changes section appears at the end of this standard
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1
---------------------- Page: 1 ----------------------
D5773 − 21
D4057 Practice for Manual Sampling of Petroleum and Petroleum Products
D4177 Practice for Automatic Sampling of Petroleum and Petroleum Products
D6751 Specification for Biodiesel Fuel Blend Stock (B100) for Middle Distillate Fuels
3
2.2 Energy Institute Standard:
IP 219 Test Method for Cloud Point of Petroleum Products
IP 446 Determination of the Cloud Point of Petroleum Products—Automatic Constant Cooling Rate Method
3. Terminology
3.1 Definitions:
3.1.1 biodiesel, n—fuel comprised of mono-alkyl esters of long chain fatty acids derived from vegetable oils or animal fats,
designated B100.
3.1.1.1 Discussion—
Biodiesel is typically produced by a reaction of a vegetable oil or animal fat with an alcohol such as methanol or ethanol in the
presence of a catalyst to yield mono-alkyl esters and glycerin, which is removed. The finished biodiesel derives approximately
10 % of its mass from the reacted alcohol. The alcohol used in the reaction may or may not come from renewable resources.
3.1.2 biodiesel blend, blend (BXX), n—blend of biodiesel fuel with diesel fuels and fuel oils.a homogeneous mixture of
hydrocarbon oils and mono-alkyl esters of long chain fatty acids.
3.1.2.1 Discussion—
In the abbreviation, BXX, the XX represents the volume percentage of biodiesel fuel in
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.