ASTM F1667-02

NOTICE: This standard has either been superceded and replaced by a new version or discontinued.
Contact ASTM International (www.astm.org) for the latest information.
Designation: F 1667 – 02
Standard Specification for
1
Driven Fasteners: Nails, Spikes, and Staples
This standard is issued under the fixed designation F 1667; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (e) indicates an editorial change since the last revision or reapproval.
This standard has been approved for use by agencies of the Department of Defense. The Commercial and Government Entity (Cage)
Code for ASTM: 81346.
5
1. Scope F 680 Test Methods for Nails
F 1575 Test Method for Determining Bending Yield Mo-
1.1 This specification covers nails, spikes, staples, and other
5
ment of Nails
driven fasteners, as listed in Table 1.
NOTE 1—Fastener ductility information is presented in Table 2 and 3. Terminology
dimensional information in Tables 3-63.
3.1 Definitions—The definitions used in this specification
1.2 Fasteners described in this specification are driven by
are those of common commercial acceptance and usage and
hand tool, power tool, or mechanical device in single or
also appear in Terminologies F 547 and F 592.
multiple strikes and may be positioned for striking by hand,
4. Classification
tool, or machine.
1.3 The values stated in inch-pound units are to be regarded 4.1 The fasteners and their Table 1 classification are iden-
as the standard.
tified as follows:
1.4 This standard does not purport to address all of the
NOTE 2—The identification of fasteners, classified by style and type
safety concerns, if any, associated with its use. It is the
(alpha indicators) followed by a dash number (numerical code) based on
responsibility of the user of this standard to establish appro-
Tables 3-63, identifies dimensions specifically and establishes a PIN (part
priate safety and health practices and determine the applica-
identifying number) system when preceded by the F 1667 ASTM desig-
nator of this specification. For example:
bility of regulatory limitations prior to use.
2. Referenced Documents
2.1 ASTM Standards:
A 153/A 153M Specification for Zinc Coating (Hot-Dip) on
2
Iron and Steel Hardware
A 510 Specification for General Requirements for Wire
3
Rods and Coarse Round Wire, Carbon Steel
A 641/A 641M Specification for Zinc-Coated (Galvanized)
2
Carbon Steel Wire
B 695 Specification for Coatings of Zinc Mechanically
4
Deposited on Iron and Steel
4.2 The trade designation, S, pennyweight, used in commer-
F 547 Terminology of Nails for Use with Wood and Wood-
5
Base Materials cial practice is referenced in Tables 3-63 wherever it applies.
F 592 Terminology of Collated and Cohered Fasteners and
5. Ordering Information
5
Their Application Tools
5.1 Orders for driven fasteners under this specification shall
include the following information:
1 5.1.1 Quantity or weight;
This specification is under the jurisdiction of ASTM Committee F16 on
Fasteners and is the direct responsibility of Subcommittee F16.05 on Driven and 5.1.2 Part identifying number (PIN) or product description
Other Fasteners.
(see 4.1 and appropriate table);
Current edition approved April 10, 2002. Published April 2002. Originally
5.1.3 Special material requirements, if specified, including
published as F 1667–95. Last previous edition F 1667–01a.
2
coatings or finishes;
Annual Book of ASTM Standards, Vol 01.06.
3
Annual Book of ASTM Standards, Vol 01.03.
5.1.4 ASTM designation;
4
Annual Book of ASTM Standards, Vol 02.05.
5.1.5 Packaging requirements;
5
Annual Book of ASTM Standards, Vol 01.08.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.
1

---------------------- Page: 1 ----------------------
NOTICE: This standard has either been superceded and replaced by a new version or discontinued.
Contact ASTM International (www.astm.org) for the latest information.
F 1667
TABLE 1 Classification and Identification Index TABLE 2 Bend Angles for Fasteners Using the Test Methods
F 680 Bend Test
Type Style Style Identification Table
Fastener Material Bend
I—Nails (NL) 1. Brads BR 3
Angle, °
2. Barrel BL 4
3. Boat BTH/BTL 5
1. Steel wire: (low-carbon, medium-low 180
4. Box A BXA 6 carbon, medium-carbon) (unhardened)
Box B BXB 7
2. Stainless steel wire 180
5. Broom BM 8 3. Hardened steel fasteners 20
6. Casing CN 9
4. Sheet steel for cut nails, Type II, 90
7. Cooler CL 10 and cut spikes, Type III
8. Sinker SK 11
5. Copper (min 98 %) 180
9. Corker CK 12
6. Copper clad wire (min 20 %) 180
10. Common CMA 13
7. Aluminum alloy wire 90
Common CMC 14
8. Brass wire 180
Common CMS 15
Common CMM 16
11. Concrete CTS/CTM 17
12. Double-headed DH 18
13. Fine FN 19 shall be of low carbon, medium-low carbon, or medium-high
14. Finishing FH 20
carbon.
15. Flooring FL 21
6.2 St
...