iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
ASTM

ASTM D7633-10b

(Test Method)

Standard Test Method for Carbon Black(em dash)Carbon Content

Standard Test Method for Carbon Black(em dash)Carbon Content

SIGNIFICANCE AND USE
The total carbon content of a carbon black is a requirement for the calculation and reporting of carbon dioxide emissions. It can also be used in calculations to estimate yield of the process.
SCOPE
1.1 This test method covers the instrumental determination of carbon content in a carbon black sample. Values obtained represent the total carbon content.
1.2 The method is applicable to tread, carcass and specialty type carbon blacks obtained from partial combustion or thermal decomposition processes, which typically contain 95-100 % carbon.  
1.3 The results of these tests can be expressed as mass % carbon.
1.4 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.
1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

General Information

Status
Historical
Publication Date
30-Nov-2010
ICS
71.060.10 - Chemical elements
Technical Committee
D24 - Carbon Black
Drafting Committee
D24.66 - Environment, Health, and Safety
Current Stage
Ref Project

Relations

Replaces
ASTM D7633-10a - Standard Test Method for Carbon Black<char: emdash>CARBON CONTENT
Effective Date
01-Dec-2010
Replaced By
ASTM D7633-13 - Standard Test Method for Carbon Black&mdash;Carbon Content
Effective Date
01-Nov-2013
Referred By
ASTM D7662-15(2020) - Standard Test Method for Carbon Content in Carbon Black Feedstock Oils
Effective Date
01-Dec-2010

Buy Standard

ASTM D7633-10b - Standard Test Method for Carbon Black(em dash)Carbon ContentASTM D7633-10b - Standard Test Method for Carbon Black(em dash)Carbon Content
PreviousNext
Standard
ASTM D7633-10b - Standard Test Method for Carbon Black(em dash)Carbon Content
English language
2 pages
sale 15% off
Preview
sale 15% off
Preview
REDLINE ASTM D7633-10b - Standard Test Method for Carbon Black(em dash)Carbon ContentREDLINE ASTM D7633-10b - Standard Test Method for Carbon Black(em dash)Carbon Content
PreviousNext
Standard
REDLINE ASTM D7633-10b - Standard Test Method for Carbon Black(em dash)Carbon Content
English language
2 pages
sale 15% off
Preview
sale 15% off
Preview

Standards Content (Sample)

NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation: D7633 − 10b
StandardTest Method for
1
Carbon Black—Carbon Content
This standard is issued under the fixed designation D7633; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope magnesium perchlorate. The gas stream is then passed through
a cell in which carbon dioxide concentration is measured by an
1.1 This test method covers the instrumental determination
infrared (IR) absorption detector at a precise wavelength in the
of carbon content in a carbon black sample. Values obtained
IR spectrum.
represent the total carbon content.
3.2 This test method is for use with commercially available
1.2 The method is applicable to tread, carcass and specialty
carbon analyzers equipped to carry out the combustion and
type carbon blacks obtained from partial combustion or ther-
measurement operations automatically.
mal decomposition processes, which typically contain 95-
100 % carbon. 3.3 The carbon analyzer must be calibrated using an appro-
priate calibration standard (see 6.4).
1.3 The results of these tests can be expressed as mass %
carbon.
4. Significance and Use
1.4 The values stated in SI units are to be regarded as
4.1 The total carbon content of a carbon black is a require-
standard. No other units of measurement are included in this
ment for the calculation and reporting of carbon dioxide
standard.
emissions. It can also be used in calculations to estimate yield
1.5 This standard does not purport to address all of the
of the process.
safety concerns, if any, associated with its use. It is the
5. Apparatus
responsibility of the user of this standard to establish appro-
priate safety and health practices and determine the applica-
5.1 Analytical Balance,orequivalent,capableofaweighing
bility of regulatory limitations prior to use.
sensitivity of 1 mg or better resolution.
5.2 Gravity Convection Drying Oven, capable of maintain-
2. Referenced Documents
ing 125 6 5°C.
2
2.1 ASTM Standards:
5.3 Measurement Apparatus, equipped to automatically
D1799 Practice for Carbon Black—Sampling Packaged
combust the sample and measure carbon content.
Shipments
D1900 Practice for Carbon Black—Sampling Bulk Ship-
5.4 Combustion tube and boat made of a suitable material
ments
such as mullite, porcelain or zircon.
3. Summary of Test Method
6. Reagents
3.1 In this test method, a sample is weighed in a combustion
6.1 Purity of Reagents—Reagent grade chemicals shall be
boat and the carbon content is determined by placing the boat
used in all tests. Unless otherwise indicated, it is intended that
in a tube furnace operating at 1350°C in a stream of oxygen
all reagents shall conform to the specifications of the Commit-
resulting in complete combustion. Carbon in the sample is
tee onAnalytical Reagents of theAmerican Chemical Society,
oxidized to carbon dioxide. Moisture and particulates are 3
where such specifications are available. Other grades may be
removed from the gas stream by traps filled with anhydrous
used, provided it is first ascertained that the reagent is of
sufficiently high purity to permit its use without lessening the
1
accuracy of the determination.
This test method is under the jurisdiction ofASTM Committee D24 on Carbon
Black and is the direct responsibility of Subcommittee D24.66 on Environment,
6.2 Magnesium Perchlorate.
Health, and Safety.
Current edition approved Dec. 1, 2010. Published January 2011. Originally
approved in 2010. Last previous edition approved in 2010 as D7633 – 10a. DOI:
3
10.1520/D7633-10B. “Reagent Chemicals,” American Chemical Society Specifications, American
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or Chemical Society, Washington, DC. For suggestions on the testing of reagents not
contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM listed by the American Chemical Society, see Analar Standards for Laboratory
Standards volume information, refer to the standard’s Document Summary page on Chemicals, BDH Ltd., Poole, Dorset, U.K. and the United States Pharmacopeia and
the ASTM website. National Formulary, U.S. Pharmacopeial Convention, Inc. (USPC), Rockville, MD.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1

---------------------- Page: 1 ----------------------
D7633 − 10b
6.3 Oxygen, high purity, 99.9 %. 10. Procedure
4
6.4 Calibration standard. 10.1 Sample Preparation—Dry an adequate sample of the
carbon black for at least1hina gravity-convection oven set at
7. Sampling
125 65°C,inanopencontainerofsuitabledimensions,sothat
the depth of black is no m
...

This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
Designation:D7633–10a Designation:D7633–10b
Standard Test Method for
1
Carbon Black—Carbon Content
This standard is issued under the fixed designation D7633; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope
1.1 This test method covers the instrumental determination of carbon content in a carbon black sample. Values obtained
represent the total carbon content.
1.2 The method is applicable to tread, carcass and specialty type carbon blacks obtained from partial combustion or thermal
decomposition processes, which typically contain 95-100 % carbon.
1.3 The results of these tests can be expressed as mass % carbon.
1.4 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.
1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility
of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory
limitations prior to use.
2. Referenced Documents
2
2.1 ASTM Standards:
D1799 Practice for Carbon BlackSampling Packaged Shipments
D1900 Practice for Carbon BlackSampling Bulk Shipments
3. Summary of Test Method
3.1 In this test method, a sample is weighed in a combustion boat and the carbon content is determined by placing the boat in
a tube furnace operating at 1350°C in a stream of oxygen resulting in complete combustion. Carbon in the sample is oxidized to
carbon dioxide. Moisture and particulates are removed from the gas stream by traps filled with anhydrous magnesium perchlorate.
The gas stream is then passed through a cell in which carbon dioxide concentration is measured by an infrared (IR) absorption
detector at a precise wavelength in the IR spectrum.
3.2 This test method is for use with commercially available carbon analyzers equipped to carry out the combustion and
measurement operations automatically.
3.3 The carbon analyzer must be calibrated using an appropriate calibration standard (see 6.4).
4. Significance and Use
4.1 The total carbon content of a carbon black is a requirement for the calculation and reporting of carbon dioxide emissions.
It can also be used in calculations to estimate yield of the process.
5. Apparatus
5.1 Analytical Balance, or equivalent, capable of a weighing sensitivity of 1 mg or better resolution.
5.2 Gravity Convection Drying Oven, capable of maintaining 125 6 5°C.
5.3 Measurement Apparatus, equipped to automatically combust the sample and measure carbon content.
5.4 Combustion tube and boat made of a suitable material such as mullite, porcelain or zircon.
6. Reagents
6.1 Purity of Reagents—Reagent grade chemicals shall be used in all tests. Unless otherwise indicated, it is intended that all
reagents shall conform to the specifications of the Committee on Analytical Reagents of the American Chemical Society, where
1
This test method is under the jurisdiction ofASTM Committee D24 on Carbon Black and is the direct responsibility of Subcommittee D24.66 on Environment, Health,
and Safety.
Current edition approved Oct. 15,Dec. 1, 2010. Published December 2010.January 2011. Originally approved in 2010. Last previous edition approved in 2010 as
D7633 – 10a. DOI: 10.1520/D7633-10AB.
2
For referencedASTM standards, visit theASTM website, www.astm.org, or contactASTM Customer Service at service@astm.org. For Annual Book of ASTM Standards
volume information, refer to the standard’s Document Summary page on the ASTM website.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.
1

---------------------- Page: 1 ----------------------
D7633–10b
3
such specifications are available. Other grades may be used, provided it is first ascertained that the reagent is of sufficiently high
purity to permit its use without lessening the accuracy of the determination.
6.2 Magnesium Perchlorate.
6.3 Oxygen, high purity, 99.9 %.
4
6.4 Calibration standard.
7. Sampling
7.1 Samples of candidate carbon blacks shall be taken in accordance with Practice D1799 or D1900.
8. Preparation of Apparatus
8.1 Assemble the apparatus according to the manufacturer’s instructions.
8.2Stabilize the furnace temperature at 1350°C.
8.2 Stabilize the furnace temperature at 1350
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

ASTM
ASTM D2414-23a(Test Method)
Standard Test Method for Carbon Black—Oil Absorption Number (OAN)

SIGNIFICANCE AND USE
4.1 The oil absorption number of a carbon black is related to the processing and vulcanizate properties of rubber compounds containing the carbon black.
SCOPE
1.1 This test method covers the determination of the oil absorption number of carbon black.  
1.2 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    10 pages
    English language
    sale 15% off
  • Standard
    10 pages
    English language
    sale 15% off
ASTM
ASTM D7633-13(2022)(Test Method)
Standard Test Method for Carbon Black—Carbon Content

SIGNIFICANCE AND USE
4.1 The total carbon content of a carbon black is a requirement for the calculation and reporting of carbon dioxide emissions. It can also be used in calculations to estimate yield of the process.
SCOPE
1.1 This test method covers the instrumental determination of carbon content in a carbon black sample. Values obtained represent the total carbon content.  
1.2 The method is applicable to tread, carcass and specialty type carbon blacks obtained from partial combustion or thermal decomposition processes, which typically contain 95 to 100 % carbon.  
1.3 The results of these tests can be expressed as mass % carbon.  
1.4 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.  
1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    3 pages
    English language
    sale 15% off
ASTM
ASTM D7854-21(Test Method)
Standard Test Method for Carbon Black-Void Volume at Mean Pressure

SIGNIFICANCE AND USE
5.1 The greater a carbon black resists compression by having substantial aggregate irregularity and non-sphericity, the greater the compressed volume and void volume. Also, the more that a carbon black resists compression, the greater the energy required to compress the sample per unit void volume.  
5.2 Structure is a property that strongly influences the physical properties developed in carbon black-elastomer compounds for use in tires, mechanical rubber goods, and other manufactured rubber products. Structure by void volume is based on compression while structure measurements by OAN (Test Method D2414) and COAN (Test Method D3493) are based on oil absorption.
SCOPE
1.1 This test method covers a procedure to measure a carbon black structure property by Void Volume at mean pressure. Compressed void volumes are obtained by measuring the compressed volume of a weighed sample in a cylindrical chamber as a function of pressure exerted by a movable piston. A profile of void volume as a function of pressure provides a means to assess carbon black structure at varying levels of density and aggregate reduction. For the purposes of standardized testing a single value of void volume is reported at 50 MPa mean pressure.  
1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    4 pages
    English language
    sale 15% off
  • Standard
    4 pages
    English language
    sale 15% off
ASTM
ASTM D6556-21(Test Method)
Standard Test Method for Carbon Black—Total and External Surface Area by Nitrogen Adsorption

SIGNIFICANCE AND USE
4.1 This test method is used to measure the total and external surface area of carbon blacks based on multipoint nitrogen adsorption. The NSA measurement is based on the B.E.T. theory and it includes the total surface area, inclusive of micropores, pore diameters less than 2 nm (20 Å). The external surface area, based on the statistical thickness method (STSA), is defined as the specific surface area that is accessible to rubber.  
4.2 CTAB Surface Area (formerly Test Method D3765) has been withdrawn. The CTAB value may be estimated from the STSA value using Eq 1. The equation is based on a linear regression of the STSA and CTAB measured values of the SRB 5 standards.
SCOPE
1.1 This test method covers the determination of the total surface area by the Brunauer, Emmett, and Teller (B.E.T. NSA) theory of multilayer gas adsorption behavior using multipoint determinations and the external surface area based on the statistical thickness surface area method.  
1.2 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. (The minimum safety equipment should include protective gloves, sturdy eye and face protection).  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    6 pages
    English language
    sale 15% off
  • Standard
    6 pages
    English language
    sale 15% off
ASTM
ASTM D5817-20(Practice)
Standard Practice for Carbon Black, Pelleted—Reduction, Blending, and Drying of Gross Samples for Testing

SIGNIFICANCE AND USE
4.1 Several test methods for carbon black require the reduction in sample size or the blending of the test sample to reduce the variation of the measured characteristic. Other factors being equal, larger samples will tend to be more representative of the total supply. This practice provides procedures for reducing the large sample obtained from the bag and bulk sampling practices to a convenient size for conducting a number of tests to describe the material and measure its quality in such a manner that the smaller portion is most likely to be a representation of the bulk sample. Failure to follow the procedures in this practice could result in providing a nonrepresentative sample to be used in subsequent testing. Individual test methods provide for minimum amounts of material to be tested.  
4.2 Test Method A, Reduction of Sample Size, is typically used to obtain an aliquot from a large sample, splitting a black into two or more equal portions, or reducing a blended black from Test Method B to a specified sample size. The final sample is always smaller than the original sample and would not be considered to be a “well blended” sample.  
4.3 Test Method B, Blending of Carbon Black, is typically used to prepare a homogeneous sample. The homogeneous sample may be used for several tests (see Note 2) or may be reduced in size by Test Method A. The final sample size is the same as the original.  
4.4 When a sample is to be blended and reduced, the sample should be blended (Test Method B) before reduction (Test Method A). The blending and reduction must be done before the sample is dried (Test Method C).
SCOPE
1.1 This practice describes the procedure for blending of pelleted carbon black, the procedure for the reduction of gross samples of pelleted carbon black to the appropriate size for testing and the preparation of the sample for testing. These techniques are intended to minimize variations in measured characteristics between test samples. Standard terminology relating to carbon black samples is found in Terminology D3053. The classification system for carbon blacks used in rubber products can be found in Classification System D1765.  
1.2 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    5 pages
    English language
    sale 15% off
  • Standard
    5 pages
    English language
    sale 15% off
ASTM
ASTM D2414-23a(Test Method)
Standard Test Method for Carbon Black—Oil Absorption Number (OAN)

SIGNIFICANCE AND USE
4.1 The oil absorption number of a carbon black is related to the processing and vulcanizate properties of rubber compounds containing the carbon black.
SCOPE
1.1 This test method covers the determination of the oil absorption number of carbon black.  
1.2 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    10 pages
    English language
    sale 15% off
  • Standard
    10 pages
    English language
    sale 15% off
ASTM
ASTM C747-23(Test Method)
Standard Test Method for Moduli of Elasticity and Fundamental Frequencies of Carbon and Graphite Materials by Sonic Resonance

SIGNIFICANCE AND USE
5.1 This test method may be used for material development, characterization, design data generation, and quality control purposes.  
5.2 This test method is primarily concerned with the room temperature determination of the dynamic moduli of elasticity and rigidity of slender rods or bars composed of homogeneously distributed carbon or graphite particles.  
5.3 This test method can be adapted for other materials that are elastic in their initial stress-strain behavior, as defined in Test Method E111.  
5.4 This basic test method can be modified to determine elastic moduli behavior at temperatures from –75 °C to +2500 °C. Thin graphite rods may be used to project the specimen extremities into ambient temperature conditions to provide resonant frequency detection by the use of transducers as described in 7.1.
SCOPE
1.1 This test method covers determination of the dynamic elastic properties of isotropic and near isotropic carbon and graphite materials at ambient temperatures. Specimens of these materials possess specific mechanical resonant frequencies that are determined by the elastic modulus, mass, and geometry of the test specimen. The dynamic elastic properties of a material can therefore be computed if the geometry, mass, and mechanical resonant frequencies of a suitable (rectangular or cylindrical) test specimen of that material can be measured. Dynamic Young's modulus is determined using the resonant frequency in the flexural or longitudinal mode of vibration. The dynamic shear modulus, or modulus of rigidity, is found using torsional resonant vibrations. Dynamic Young's modulus and dynamic shear modulus are used to compute Poisson's ratio.  
1.2 This test method determines elastic properties by measuring the fundamental resonant frequency of test specimens of suitable geometry by exciting them mechanically by a singular elastic strike with an impulse tool. Specimen supports, impulse locations, and signal pick-up points are selected to induce and measure specific modes of the transient vibrations. A transducer (for example, contact accelerometer or non-contacting microphone) senses the resulting mechanical vibrations of the specimen and transforms them into electric signals. (See Fig. 1.) The transient signals are analyzed, and the fundamental resonant frequency is isolated and measured by the signal analyzer, which provides a numerical reading that is (or is proportional to) either the frequency or the period of the specimen vibration. The appropriate fundamental resonant frequencies, dimensions, and mass of the specimen are used to calculate dynamic Young's modulus, dynamic shear modulus, and Poisson's ratio. Annex A1 contains an alternative approach using continuous excitation.
FIG. 1 Block Diagram of Typical Test Apparatus  
1.3 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.  
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    19 pages
    English language
    sale 15% off
  • Standard
    19 pages
    English language
    sale 15% off
ASTM
ASTM C714-23(Guide)
Standard Guide for Thermal Diffusivity of Carbon and Graphite by Thermal Pulse Method

SIGNIFICANCE AND USE
5.1 Thermal diffusivity is an important property required for such purposes as design applications under transient heat flow conditions, determination of safe operating temperature, process control, and quality assurance.  
5.2 The flash method is used to measure values of thermal diffusivity (α) of a wide range of solid materials. It is particularly advantageous because of the simple specimen geometry, small specimen size requirements, rapidity of measurement, and ease of handling materials having a wide range of thermal diffusivity values over a large temperature range with a single apparatus. The short measurement times involved reduce the chances of contamination and change of specimen properties due to exposure to high temperature environments.  
5.3 Thermal diffusivity results in many cases can be combined with values for specific heat (Cp) and density (ρ) to derive thermal conductivity (λ) from the relation λ = αCpρ. For guidance on converting thermal diffusivity to thermal conductivity, refer to Practice C781.  
5.4 This test method described in this guide can be used to characterize graphite for design purposes.  
5.5 Test Method E1461 is a more detailed form of this test method described in this guide and has applicability to much wider ranges of materials, applications, and temperatures.
SCOPE
1.1 This guide covers the determination of the thermal diffusivity of carbons and graphite at temperatures up to 500 °C. It is applicable only to small easily fabricated specimens. Thermal diffusivity values in the range from 0.04 cm2/s to 2.0 cm2/s are readily measurable by this guide; however, for the reason outlined in Section 7, for materials outside this range this guide may not be applicable.  
1.2 Units—The values stated in SI units are to be regarded as the standard. No other units of measurement are included in this standard.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Guide
    5 pages
    English language
    sale 15% off
  • Guide
    5 pages
    English language
    sale 15% off
ASTM
ASTM C562-23(Test Method)
Standard Test Method for Moisture in a Graphite Sample

SIGNIFICANCE AND USE
4.1 This test method is applicable only for determination of the volatile moisture content resulting from adsorption of water vapor from the atmosphere, and is not intended to give representative moisture data for graphite that has been exposed to liquid water contamination.
SCOPE
1.1 This test method provides a practical determination for the percentage of moisture in a graphite sample.  
1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    2 pages
    English language
    sale 15% off
  • Standard
    2 pages
    English language
    sale 15% off
ASTM
ASTM C561-23(Test Method)
Standard Test Method for Ash in a Graphite Sample

SIGNIFICANCE AND USE
4.1 This test method provides a practical estimate of nonburnable residues in commercially available graphite materials. The ash values determined by this test method are of use in comparing the relative purity of various grades of graphite. To facilitate use, this test method institutes simplifications that preclude the ability to determine absolutely the ash values of the test graphite material due to uncontrolled sources of trace contamination.  
4.2 This test method is not intended for use in determining the ash content of purified graphites, for example, nuclear materials. The relationship between the mineral content of a graphite sample and the ash content of that sample is unknown and is not determined by the application of this test method.
SCOPE
1.1 This test method provides a practical determination for the ash content in a graphite sample.  
1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    3 pages
    English language
    sale 15% off
  • Standard
    3 pages
    English language
    sale 15% off