ASTM F467-08e1
(Specification)Standard Specification for Nonferrous Nuts for General Use
Standard Specification for Nonferrous Nuts for General Use
ABSTRACT
This specification covers the chemical, mechanical, dimensional, and workmanship and finish requirements, and the corresponding test methods for commercial wrought nonferrous nuts in a variety of alloys in common use that are intended for general service applications. When tested, the nuts shall meet required values for hardness, proof stress, and tensile stress areas.
SIGNIFICANCE AND USE
For purposes of determining compliance with the specified limits for requirements of the properties listed in this specification, an observed value or calculated value shall be rounded in accordance with Practice E29.
SCOPE
1.1 This specification covers the requirements for commercial wrought nonferrous nuts 0.250 to 1.500 in. inclusive in diameter in a number of alloys in common use and intended for general service applications.
1.2 Applicable bolts, cap screws, and studs for use with nuts covered by this specification are covered by Specification F468.
1.3 This specification is the inch-pound companion to Specification F467M; therefore, no SI equivalents are presented in the specification.
General Information
Relations
Buy Standard
Standards Content (Sample)
NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
´1
Designation:F467 −08
StandardSpecification for
1
Nonferrous Nuts for General Use
ThisstandardisissuedunderthefixeddesignationF467;thenumberimmediatelyfollowingthedesignationindicatestheyearoforiginal
adoption or, in the case of revision, the year of last revision.Anumber in parentheses indicates the year of last reapproval.Asuperscript
epsilon (´) indicates an editorial change since the last revision or reapproval.
This standard has been approved for use by agencies of the Department of Defense.
1
ε NOTE—7.1 was editorially corrected in October 2009.
3
1. Scope* and Nickel-Chromium-Iron Alloys (Withdrawn 1989)
E53 Test Method for Determination of Copper in Unalloyed
1.1 This specification covers the requirements for commer-
Copper by Gravimetry
cial wrought nonferrous nuts 0.250 to 1.500 in. inclusive in
E54 Test Methods for ChemicalAnalysis of Special Brasses
diameterinanumberofalloysincommonuseandintendedfor
3
and Bronzes (Withdrawn 2002)
general service applications.
E55 Practice for Sampling Wrought Nonferrous Metals and
1.2 Applicablebolts,capscrews,andstudsforusewithnuts
Alloys for Determination of Chemical Composition
covered by this specification are covered by Specification
E62 Test Methods for Chemical Analysis of Copper and
F468. 3
CopperAlloys (Photometric Methods) (Withdrawn 2010)
1.3 This specification is the inch-pound companion to E75 Test Methods for Chemical Analysis of Copper-Nickel
3
Specification F467M; therefore, no SI equivalents are pre-
and Copper-Nickel-Zinc Alloys (Withdrawn 2010)
sented in the specification. E76 Test Methods for Chemical Analysis of Nickel-Copper
3
Alloys (Withdrawn 2003)
2. Referenced Documents
E92 Test Method forVickers Hardness of Metallic Materials
3
2
(Withdrawn 2010)
2.1 ASTM Standards:
E101 TestMethodforSpectrographicAnalysisofAluminum
B154 Test Method for Mercurous Nitrate Test for Copper
and Aluminum Alloys by the Point-to-Plane Technique
Alloys
3
(Withdrawn 1996)
B574 Specification for Low-Carbon Nickel-Chromium-
E120 Test Methods for Chemical Analysis of Titanium and
Molybdenum, Low-Carbon Nickel-Molybdenum-
3
Titanium Alloys (Withdrawn 2003)
Chromium, Low-Carbon Nickel-Molybdenum-
E165 Practice for Liquid Penetrant Examination for General
Chromium-Tantalum, Low-Carbon Nickel-Chromium-
Industry
Molybdenum-Copper, and Low-Carbon Nickel-
E227 Test Method for Optical Emission Spectrometric
Chromium-Molybdenum-Tungsten Alloy Rod
Analysis of Aluminum and Aluminum Alloys by the
D3951 Practice for Commercial Packaging
3
Point-to-Plane Technique (Withdrawn 2002)
E18 Test Methods for Rockwell Hardness of Metallic Ma-
E354 Test Methods for Chemical Analysis of High-
terials
Temperature,Electrical,Magnetic,andOtherSimilarIron,
E29 Practice for Using Significant Digits in Test Data to
Nickel, and Cobalt Alloys
Determine Conformance with Specifications
E478 Test Methods for ChemicalAnalysis of CopperAlloys
E34 Test Methods for Chemical Analysis of Aluminum and
E1409 Test Method for Determination of Oxygen and Nitro-
Aluminum-Base Alloys
gen in Titanium and Titanium Alloys by the Inert Gas
E38 Methods for Chemical Analysis of Nickel-Chromium
Fusion Technique
F468 Specification for Nonferrous Bolts, Hex Cap Screws,
1
Socket Head Cap Screws, and Studs for General Use
This specification is under the jurisdiction of ASTM Committee F16 on
Fasteners and is the direct responsibility of Subcommittee F16.04 on Nonferrous
F606 Test Methods for Determining the Mechanical Proper-
Fasteners.
ties of Externally and Internally Threaded Fasteners,
Current edition approved May 1, 2008. Published June 2008. Originally
ε1 Washers, Direct Tension Indicators, and Rivets
approved in 1976. Last previous edition approved in 2006 as F467 – 06a . DOI:
10.1520/F0467-08E01.
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or
contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM
3
Standards volume information, refer to the standard’s Document Summary page on The last approved version of this historical standard is referenced on
the ASTM website. www.astm.org.
*A Summary of Changes section appears at the end of this standard
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1
---------------------- Page: 1 ----------------------
´1
F467−08
F1470 Practice for Fastener Sampling for Specified Me- 4.2.3 Stress Relieving—Whenrequired,stressrelievingshall
chanical Properties and Performance Inspection be specified by the purchaser for all copper alloys and nickel
4
2.2 ASME Standards: alloys 400 and 405.
B 1.1 Unified Inch Screw Threads (UN and UNR Thread
5. Chemical Composition
Form)
B 18.2.2 Square and Hex Nuts
5.1 Chemical Composition—The nuts shall conform to the
chemical composition specified in Table 1 for the specified
3. Ordering Informa
...
This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
´1
Designation:F 467M–06a Designation: F467 – 08
Standard Specification for
1
Nonferrous Nuts for General Use [Metric]
This standard is issued under the fixed designation F 467M;F467; the number immediately following the designation indicates the year
of original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval.
A superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
This standard has been approved for use by agencies of the Department of Defense.
1
´ NOTE—7.1 was editorially corrected in October 2009.
1. Scope*
1.1 This specification covers the requirements for commercial wrought nonferrous nuts in nominal thread diameters M6 to M36
inclusive 0.250 to 1.500 in. inclusive in diameter in a number of alloys in common use and intended for general service
applications.
1.2 Applicable bolts, cap screws, and studs for use with nuts covered by this specification are covered by Specification F
468MF468MF468. Note1—This specification is the metric companion of Specification F 467.
1.3 This specification is the inch-pound companion to Specification F467M; therefore, no SI equivalents are presented in the
specification.
2. Referenced Documents
2
2.1 ASTM Standards:
B154 Test Method for Mercurous Nitrate Test for Copper Alloys
B574 Specification for Low-Carbon Nickel-Chromium-Molybdenum, Low-Carbon Nickel-Molybdenum-Chromium-Tantalum,
Low-CarbonNickel-Chromium-Molybdenum-Copper,andLow-CarbonNickel-Chromium-Molybdenum-TungstenAlloyRod
D3951 Practice for Commercial Packaging
E18 Test Methods for Rockwell Hardness of Metallic Materials
E29 Practice for Using Significant Digits in Test Data to Determine Conformance with Specifications
E34
E34 Test Methods for Chemical Analysis of Aluminum and Aluminum-Base Alloys
E38
3
E38 Methods for Chemical Analysis of Nickel-Chromium and Nickel-Chromium-Iron Alloys
E53
E53 Test Method for Determination of Copper in Unalloyed Copper by Gravimetry
E54
E54 Test Methods for Chemical Analysis of Special Brasses and Bronzes
E55 Practice for Sampling Wrought Nonferrous Metals and Alloys for Determination of Chemical Composition
E62
E62 Test Methods for Chemical Analysis of Copper and Copper Alloys (Photometric Methods)
E75
E75 Test Methods for Chemical Analysis of Copper-Nickel and Copper-Nickel-Zinc Alloys
E76
E76 Test Methods for Chemical Analysis of Nickel-Copper Alloys
E92 Test Method for Vickers Hardness of Metallic Materials
E101101 Test Method for Spectrographic Analysis of Alu-minumAluminum and Aluminum Alloys by the Point-tTo-Plane
0
Technique
E120 Test Methods for Chemical Analysis of Titanium and Titanium Alloys
1
This specification is under the jurisdiction of ASTM Committee F16 on Fasteners and is the direct responsibility of Subcommittee F16.04 on Nonferrous Fasteners.
Current edition approved Aug. 1, 2006. Published August 2006. Originally approved in 1979. Last previous edition approved in 2006 as F 467M–06.
´1
Current edition approved May 1, 2008. Published June 2008. Originally approved in 1976. Last previous edition approved in 2006 as F467 – 06a . DOI:
10.1520/F0467-08E01.
2
For referencedASTM standards, visit theASTM website, www.astm.org, or contactASTM Customer Service at service@astm.org. For Annual Book of ASTM Standards
volume information, refer to the standard’s Document Summary page on the ASTM website.
3
Withdrawn.
*A Summary of Changes section appears at the end of this standard.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.
1
---------------------- Page: 1 ----------------------
´1
F467 – 08
E165 Practice for Liquid Penetrant Examination for General Industry
E227
E227 Test Method for Optical Emission Spectrometric Analysis of Aluminum and Aluminum Alloys by the Point-to-Plane
Technique
E354
E354 Test Methods for Chemical Analysis of High-Temperature, Electrical, Magnetic, and Other Similar Iron, Nickel, and
Cobalt Alloys
E478
E478 Test Methods for Chemical Analysis of Copper Alloys
E1409
E1409 Test Method for Determination of Oxygen and Nitrogen in Titanium and Titanium Alloys by the Inert Gas Fusion
Technique
F468M468 Specification for Nonferrous Bolts, Hex Cap Screws, and Studs for General Use (Metric)
F606M606 Test Methods for Determining the Mechanical Properties of Externally and InternallyThreaded Fasteners,Washers,
Direct Tension Indicators, and Rivets (Metric)
F1470 Practice for Fastener Sampling for Specified Mechanical Properties and Performance
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.