Standard Specification for Metal Press Insert Fittings with Factory Assembled Stainless Steel Press Sleeve for SDR9 Cross-linked Polyethylene (PEX) Tubing

SCOPE
1.1 This specification covers copper alloy metal press insert fittings with factory assembled stainless steel press sleeves incorporating 3 view holes and tool locator ring. These fittings are for use with cross-linked polyethylene (PEX) tubing in nominal sizes 5/16 , 3/8 , 1/2 , 5/8 , 3/4 , 1, 11/4 , 1 1/2 , and 2 that meet the requirements for Specification F876 or F3253. These fittings are intended for use in 100 psi (689.5 kPa) systems operating at temperatures up to, and including, 180 °F (82 °C). The requirements for materials, workmanship, dimensions, and markings to be used on the fittings and sleeves are also included. The components covered by this specification are intended for use in residential and commercial, hot and cold, potable water distribution systems as well as sealed central heating, including under-floor heating/cooling systems, and residential fire sprinkler systems.  
1.2 Units—The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

General Information

Status
Historical
Publication Date
31-Jan-2020
Technical Committee
Drafting Committee
Current Stage
Ref Project

Relations

Buy Standard

Technical specification
ASTM F3347-20 - Standard Specification for Metal Press Insert Fittings with Factory Assembled Stainless Steel Press Sleeve for SDR9 Cross-linked Polyethylene (PEX) Tubing
English language
6 pages
sale 15% off
Preview
sale 15% off
Preview
Technical specification
REDLINE ASTM F3347-20 - Standard Specification for Metal Press Insert Fittings with Factory Assembled Stainless Steel Press Sleeve for SDR9 Cross-linked Polyethylene (PEX) Tubing
English language
6 pages
sale 15% off
Preview
sale 15% off
Preview

Standards Content (Sample)

NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation:F3347 −20
Standard Specification for
Metal Press Insert Fittings with Factory Assembled
Stainless Steel Press Sleeve for SDR9 Cross-linked
1
Polyethylene (PEX) Tubing
This standard is issued under the fixed designation F3347; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope* 2. Referenced Documents
2
1.1 This specification covers copper alloy metal press insert 2.1 ASTM Standards:
fittings with factory assembled stainless steel press sleeves A269/A269M Specification for Seamless and Welded Aus-
incorporating 3 view holes and tool locator ring. These fittings tenitic Stainless Steel Tubing for General Service
are for use with cross-linked polyethylene (PEX) tubing in B124/B124M Specification for Copper and Copper Alloy
5 3 1 5 3 1 1
nominalsizes ⁄16, ⁄8, ⁄2, ⁄8, ⁄4,1,1 ⁄4,1 ⁄2,and2thatmeetthe Forging Rod, Bar, and Shapes
requirements for Specification F876 or F3253. These fittings B16/B16M Specification for Free-Cutting Brass Rod, Bar
are intended for use in 100 psi (689.5 kPa) systems operating and Shapes for Use in Screw Machines
at temperatures up to, and including, 180 °F (82 °C). The B283/B283M Specification for Copper and Copper-Alloy
requirements for materials, workmanship, dimensions, and Die Forgings (Hot-Pressed)
markings to be used on the fittings and sleeves are also B371/B371M Specification for Copper-Zinc-Silicon Alloy
included. The components covered by this specification are Rod
3
intended for use in residential and commercial, hot and cold,
2.2 ASME Standards:
potable water distribution systems as well as sealed central
B584 Specification for Copper Alloy Sand Castings for
heating, including under-floor heating/cooling systems, and
General Applications
residential fire sprinkler systems.
D1600 Terminology forAbbreviatedTerms Relating to Plas-
tics
1.2 Units—The values stated in inch-pound units are to be
D2122 Test Method for Determining Dimensions of Ther-
regarded as standard. The values given in parentheses are
moplastic Pipe and Fittings
mathematical conversions to SI units that are provided for
E92 Test Methods for Vickers Hardness and Knoop Hard-
information only and are not considered standard.
ness of Metallic Materials
1.3 This standard does not purport to address all of the
F412 Terminology Relating to Plastic Piping Systems
safety concerns, if any, associated with its use. It is the
F876 SpecificationforCrosslinkedPolyethylene(PEX)Tub-
responsibility of the user of this standard to establish appro-
ing
priate safety, health, and environmental practices and deter-
F877 SpecificationforCrosslinkedPolyethylene(PEX)Hot-
mine the applicability of regulatory limitations prior to use.
and Cold-Water Distribution Systems
1.4 This international standard was developed in accor-
F3253 Specification for Crosslinked Polyethylene (PEX)
dance with internationally recognized principles on standard-
Tubing with Oxygen Barrier for Hot- and Cold-Water
ization established in the Decision on Principles for the
Hydronic Distribution Systems
Development of International Standards, Guides and Recom-
mendations issued by the World Trade Organization Technical
Barriers to Trade (TBT) Committee.
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or
contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM
1
This test method is under the jurisdiction of ASTM Committee F17 on Plastic Standards volume information, refer to the standard’s Document Summary page on
Piping Systems and is the direct responsibility of Subcommittee F17.10 on Fittings. the ASTM website.
3
Current edition approved Feb. 1, 2020. Published February 2020. Originally Available from American Society of Mechanical Engineers (ASME), ASME
approved in 2018. Last previous edition approved in 2019 as F3347–19a. DOI: International Headquarters, Two Park Ave., New York, NY 10016-5990, http://
10.1520/F3347–20 www.asme.org.
*A Summary of Changes section appears at the end of this standard
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1

---------------------- Page: 1 ----------------------
F3347−20
4
2.3 ASME Standards: 5.1.1 Cast Copper Alloys—Cast copper alloy fittings shall
B1.20.1 Pipe Threads General Purpose (Inch) be made from material meeting the requirements of Specifica-
B16.18 Cast Copper Alloy Solder Joint Pressure Fittings tion B584, copper alloy UNS Nos. C87710 or C87850 or
B16.22 Wrought Copper and Copper Alloy Solder Joint StandardEN1982,copperalloyENSymbolCuSn4Zn6Pb3–C.
Pressure Fittings
5.1.2 Machined Copper Alloy—Ma
...

This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
Designation: F3347 − 19a F3347 − 20
Standard Specification for
Metal Press Insert Fittings with Factory Assembled
Stainless Steel Press Sleeve for SDR9 Cross-linked
1
Polyethylene (PEX) Tubing
This standard is issued under the fixed designation F3347; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope*
1.1 This specification covers copper alloy metal press insert fittings with factory assembled stainless steel press sleeves
incorporating 3 view holes and tool locator ring. These fittings are for use with cross-linked polyethylene (PEX) tubing in nominal
5 3 1 5 3 1 1
sizes ⁄16, ⁄8, ⁄2, ⁄8, ⁄4, 1, 1 ⁄4, 1 ⁄2, and 2 that meet the requirements for Specification F876 or F3253. These fittings are intended
for use in 100 psi (689.5 kPa) systems operating at temperatures up to, and including, 180 °F (82 °C). The requirements for
materials, workmanship, dimensions, and markings to be used on the fittings and sleeves are also included. The components
covered by this specification are intended for use in residential and commercial, hot and cold, potable water distribution systems
as well as sealed central heating, including under-floor heating/cooling systems, and residential fire sprinkler systems.
1.2 Units—The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are
mathematical conversions to SI units that are provided for information only and are not considered standard.
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility
of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of
regulatory limitations prior to use.
1.4 This international standard was developed in accordance with internationally recognized principles on standardization
established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued
by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
2. Referenced Documents
2
2.1 ASTM Standards:
A269/A269M Specification for Seamless and Welded Austenitic Stainless Steel Tubing for General Service
B124/B124M Specification for Copper and Copper Alloy Forging Rod, Bar, and Shapes
B16/B16M Specification for Free-Cutting Brass Rod, Bar and Shapes for Use in Screw Machines
B283/B283M Specification for Copper and Copper-Alloy Die Forgings (Hot-Pressed)
B371/B371M Specification for Copper-Zinc-Silicon Alloy Rod
3
2.2 ASME Standards:
B584 Specification for Copper Alloy Sand Castings for General Applications
D1600 Terminology for Abbreviated Terms Relating to Plastics
D2122 Test Method for Determining Dimensions of Thermoplastic Pipe and Fittings
E92 Test Methods for Vickers Hardness and Knoop Hardness of Metallic Materials
F412 Terminology Relating to Plastic Piping Systems
F876 Specification for Crosslinked Polyethylene (PEX) Tubing
F877 Specification for Crosslinked Polyethylene (PEX) Hot- and Cold-Water Distribution Systems
F3253 Specification for Crosslinked Polyethylene (PEX) Tubing with Oxygen Barrier for Hot- and Cold-Water Hydronic
Distribution Systems
1
This test method is under the jurisdiction of ASTM Committee F17 on Plastic Piping Systems and is the direct responsibility of Subcommittee F17.10 on Fittings.
Current edition approved Nov. 1, 2019Feb. 1, 2020. Published November 2019February 2020. Originally approved in 2018. Last previous edition approved in 2019 as
F3347–19.–19a. DOI: 10.1520/F3347–19A10.1520/F3347–20
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM Standards
volume information, refer to the standard’s Document Summary page on the ASTM website.
3
Available from American Society of Mechanical Engineers (ASME), ASME International Headquarters, Two Park Ave., New York, NY 10016-5990, http://
www.asme.org.
*A Summary of Changes section appears at the end of this standard
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1

---------------------- Page: 1 ----------------------
F3347 − 20
4
2.3 ASME Standards:
B1.20.1 Pipe Threads General Purpose (Inch)
B16.18 Cast Copper Alloy Solder J
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.