ASTM D4397-09
(Specification)Standard Specification for Polyethylene Sheeting for Construction, Industrial, and Agricultural Applications
Standard Specification for Polyethylene Sheeting for Construction, Industrial, and Agricultural Applications
ABSTRACT
This specification covers polyethylene sheeting with a determined thickness intended for construction, industrial and agricultural applications. The sheeting shall be made from polyethylene or modified polyethylene, such as an ethylene copolymer consisting of a major portion of ethylene in combination with a minor portion of some other monomer, or a mixture of polyethylene with a lesser amount of other polymers. General requirements for the material are also observed according to their appearance, dimensions in size and tolerance and minimum net weight. The sheeting may be natural, color-tinted, translucent or opaque. The tests given are intended primarily for use as production tests in conjunction with manufacturing processes and inspection methods to insure conformity of sheeting with the requirements of this specification. These tests shall be done in order to determine the following properties: thickness, length and width, weight, impact resistance, tensile properties, reflectance, luminous transmittance, water vapor transmission, and heat sealability.
SCOPE
1.1 This specification covers polyethylene sheeting, 250 μm (0.010 in. or 10 mils) or less in thickness, intended for construction, industrial, and agricultural applications.
1.2 The values stated in SI units are to be regarded as the standard.
1.3 The following precautionary statement pertains only to the test methods portion, Section 8 of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
Note 1—There is no known ISO equivalent to this specification.
General Information
Relations
Buy Standard
Standards Content (Sample)
NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation: D4397 – 09
Standard Specification for
Polyethylene Sheeting for Construction, Industrial, and
1
Agricultural Applications
This standard is issued under the fixed designation D4397; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision.Anumber in parentheses indicates the year of last reapproval.A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
This standard has been approved for use by agencies of the Department of Defense.
1. Scope* Film Test Specimens
E96/E96M Test Methods for Water Vapor Transmission of
1.1 Thisspecificationcoverspolyethylenesheeting,250µm
Materials
(0.010 in. or 10 mils) or less in thickness, intended for
E1347 Test Method for Color and Color-Difference Mea-
construction, industrial, and agricultural applications.
surement by Tristimulus Colorimetry
1.2 The values stated in SI units are to be regarded as the
F88 Test Method for Seal Strength of Flexible Barrier
standard.
Materials
1.3 The following precautionary statement pertains only to
2.2 Military Standard:
the test methods portion, Section 8 of this specification: This
MIL-STD-105 Sampling Procedures and Tables for Inspec-
standard does not purport to address all of the safety concerns,
3
tion by Attributes
if any, associated with its use. It is the responsibility of the user
of this standard to establish appropriate safety and health
3. Terminology
practices and determine the applicability of regulatory limita-
3.1 Definitions—The plastics terminology used in this
tions prior to use.
specification is in accordance with the definitions given in
NOTE 1—There is no known ISO equivalent to this specification.
Terminology D883.
3.2 Definitions of Terms Specific to This Standard:
2. Referenced Documents
3.2.1 nominal length—the length of sheeting in any roll, as
2
2.1 ASTM Standards:
specified on product labels, invoices, sales literature, and the
D618 Practice for Conditioning Plastics for Testing
like.
D882 Test Method for Tensile Properties of Thin Plastic
3.2.2 nominal net weight—the weight of sheeting in any
Sheeting
roll, as specified on product labels, invoices, sales literature,
D883 Terminology Relating to Plastics
and the like.
D1505 Test Method for Density of Plastics by the Density-
3.2.3 nominal thickness—the thickness of sheeting in any
Gradient Technique
roll, as specified on product labels, invoices, sales literature,
D1709 Test Methods for Impact Resistance of Plastic Film
and the like.
by the Free-Falling Dart Method
3.2.4 nominal width—the width of sheeting in any rolls, as
D1898 Practice for Sampling of Plastics
specified on product labels, invoices, sales literature, and the
D2103 Specification for Polyethylene Film and Sheeting
like.
D3892 Practice for Packaging/Packing of Plastics
D4976 Specification for Polyethylene Plastics Molding and
4. Materials
Extrusion Materials
4.1 The sheeting shall be made from polyethylene or modi-
D6988 Guide for Determination of Thickness of Plastic
fied polyethylene, such as an ethylene copolymer consisting of
a major portion of ethylene in combination with a minor
1 portion of some other monomer, or a mixture of polyethylene
This specification is under the jurisdiction of ASTM Committee D20 on
with a lesser amount of other polymers.
Plastics and is the direct responsibility of Subcommittee D20.19 on Molded and
Extruded Products.
NOTE 2—Polyethylene sheeting is made in a variety of colors, opaci-
Current edition approved May 1, 2009. Published June 2009. Originally
ties, translucencies, and dimensions. It is recommended that manufactur-
approved in 1984. Last previous edition approved in 2008 as D4397–08. DOI:
10.1520/D4397-09. ers be consulted on the varieties available.
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or
contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM
3
Standards volume information, refer to the standard’s Document Summary page on AvailablefromStandardizationDocumentsOrderDesk,Bldg.4SectionD,700
the ASTM website. Robbins Ave., Philadelphia, PA 19111-5094, Attn: NPODS.
*ASummary of Changes section appears at the end of this standard.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.
1
---------------------- Page: 1 ----------------------
D4397 – 09
TABLE 2 Mechanical Properties
5. General Requirements
Lengthwise Crosswise
5.1 Appearance—Thesheetingshallhaveappearancequali-
Direction Direction
ties conforming with those produced by good commercial
Tensile strength, min, MPa (psi) 11.7 (1700) 8.3 (1200)
A
Elongation, min, % 225 350
practices.Itshallbeasfreeasiscommerciallypossibleofgels,
A
streaks, pinholes, particles of foreign matter, and undispersed
For films
...
This document is not anASTM standard and is intended only to provide the user of anASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
Designation:D4397–08 Designation: D 4397 – 09
Standard Specification for
Polyethylene Sheeting for Construction, Industrial, and
1
Agricultural Applications
This standard is issued under the fixed designation D4397; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision.Anumber in parentheses indicates the year of last reapproval.A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
This standard has been approved for use by agencies of the Department of Defense.
1. Scope*
1.1 Thisspecificationcoverspolyethylenesheeting,250µm(0.010in.or10mils)orlessinthickness,intendedforconstruction,
industrial, and agricultural applications.
1.2 The values stated in SI units are to be regarded as the standard.
1.3 The following precautionary statement pertains only to the test methods portion, Section 8 of this specification: This
standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user
of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior
to use.
NOTE 1—There is no known ISO equivalent to this specification.
2. Referenced Documents
2
2.1 ASTM Standards: D374Test Methods for Thickness of Solid Electrical Insulation
D618 Practice for Conditioning Plastics for Testing
D882 Test Method for Tensile Properties of Thin Plastic Sheeting
D883 Terminology Relating to Plastics
D1505 Test Method for Density of Plastics by the Density-Gradient Technique
D1709 Test Methods for Impact Resistance of Plastic Film by the Free-Falling Dart Method
D1898 Practice for Sampling of Plastics
D2103 Specification for Polyethylene Film and Sheeting
D3892 Practice for Packaging/Packing of Plastics
D4976 Specification for Polyethylene Plastics Molding and Extrusion Materials
D6988 Guide for Determination of Thickness of Plastic Film Test Specimens
E96/E96M Test Methods for Water Vapor Transmission of Materials
E1347 Test Method for Color and Color-Difference Measurement by Tristimulus Colorimetry
F88 Test Method for Seal Strength of Flexible Barrier Materials
2.2 Military Standard:
3
MIL-STD-105 Sampling Procedures and Tables for Inspection by Attributes
3. Terminology
3.1 Definitions—The plastics terminology used in this specification is in accordance with the definitions given in Terminology
D883.
3.2 Definitions of Terms Specific to This Standard:
3.2.1 nominal length—the length of sheeting in any roll, as specified on product labels, invoices, sales literature, and the like.
3.2.2 nominal net weight—the weight of sheeting in any roll, as specified on product labels, invoices, sales literature, and the
like.
3.2.3 nominal thickness—the thickness of sheeting in any roll, as specified on product labels, invoices, sales literature, and the
like.
1
This specification is under the jurisdiction of ASTM Committee D20 on Plastics and is the direct responsibility of Subcommittee D20.19 on Film and Sheeting .
Current edition approved Nov.May 1, 2008.2009. Published November 2008.June 2009. Originally approved in 1984. Last previous edition approved in 20022008 as
D4397–028.
2
ForreferencedASTMstandards,visittheASTMwebsite,www.astm.org,orcontactASTMCustomerServiceatservice@astm.org.For Annual Book of ASTM Standards
volume information, refer to the standard’s Document Summary page on the ASTM website.
3
Available from Standardization Documents Order Desk, Bldg. 4 Section D, 700 Robbins Ave., Philadelphia, PA 19111-5094, Attn: NPODS.
*ASummary of Changes section appears at the end of this standard.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.
1
---------------------- Page: 1 ----------------------
D4397–09
3.2.4 nominal width—the width of sheeting in any rolls, as specified on product labels, invoices, sales literature, and the like.
4. Materials
4.1 The sheeting shall be made from polyethylene or modified polyethylene, such as an ethylene copolymer consisting of a
major portion of ethylene in combination with a minor portion of some other monomer, or a mixture of polyethylene with a lesser
amount of other polymers.
NOTE 2—Polyethylene sheeting is made in a variety of colors, opacities, translucencies, and dimensions. It is recommended that manufacturers be
consulted on the varieties available.
5. General Requirements General Requirements
5.1 Appearance—Thesheetingshallhaveappearancequalit
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.