ASTM D8033-22
(Classification)Standard Classification System for Poly(Ether Ether Ketone) (PEEK) Molding and Extrusion Materials
Standard Classification System for Poly(Ether Ether Ketone) (PEEK) Molding and Extrusion Materials
SCOPE
1.1 This classification system covers poly(ether ether ketone) materials suitable for injection molding and extrusion. This classification system allows for the use of recycled materials provided that all specification requirements are met.
1.2 The properties included in this standard are those required to identify the compositions covered. Other requirements necessary to identify particular characteristics important to specialized applications are to be specified by using the suffixes in Section 5.
1.3 This classification system and subsequent line callout (specification) are intended to provide means of calling out poly(ether ether ketone) materials used in the fabrication of end items or parts. It is not intended for the selection of materials. It is recommended that material selection be made by those having expertise in the plastics field only after careful consideration of the design and the performance required of the part, the environment to which it will be exposed, the fabrication process to be employed, the cost involved, and the inherent properties of the material other than those covered by this specification.
1.4 Poly(ether ether ketone), commonly referred to as PEEK, is a member of the poly (aryl ether ketone) or PAEK family. Specification D6262 covers properties of PAEK shapes and includes shapes produced from PEEK.
Note 1: This standard and ISO 23153 address the same subject matter, but differ in technical content.
1.5 The following precautionary caveat pertains only to the test method portion, Section 11, of this classification system: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.
1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
General Information
Buy Standard
Standards Content (Sample)
This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the
Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
Designation:D8033 −22
Standard Classification System for
Poly(Ether Ether Ketone) (PEEK) Molding and Extrusion
1
Materials
This standard is issued under the fixed designation D8033; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope* 1.6 This international standard was developed in accor-
dance with internationally recognized principles on standard-
1.1 This classification system covers poly(ether ether ke-
ization established in the Decision on Principles for the
tone) materials suitable for injection molding and extrusion.
Development of International Standards, Guides and Recom-
This classification system allows for the use of recycled
mendations issued by the World Trade Organization Technical
materials provided that all specification requirements are met.
Barriers to Trade (TBT) Committee.
1.2 The properties included in this standard are those
2. Referenced Documents
required to identify the compositions covered. Other require-
2
ments necessary to identify particular characteristics important
2.1 ASTM Standards:
to specialized applications are to be specified by using the
D149 Test Method for Dielectric Breakdown Voltage and
suffixes in Section 5.
DielectricStrengthofSolidElectricalInsulatingMaterials
at Commercial Power Frequencies
1.3 This classification system and subsequent line callout
D256 Test Methods for Determining the Izod Pendulum
(specification) are intended to provide means of calling out
Impact Resistance of Plastics
poly(etheretherketone)materialsusedinthefabricationofend
D257 Test Methods for DC Resistance or Conductance of
items or parts. It is not intended for the selection of materials.
Insulating Materials
It is recommended that material selection be made by those
D618 Practice for Conditioning Plastics for Testing
having expertise in the plastics field only after careful consid-
D638 Test Method for Tensile Properties of Plastics
eration of the design and the performance required of the part,
D648 Test Method for Deflection Temperature of Plastics
the environment to which it will be exposed, the fabrication
Under Flexural Load in the Edgewise Position
process to be employed, the cost involved, and the inherent
D790 Test Methods for Flexural Properties of Unreinforced
properties of the material other than those covered by this
and Reinforced Plastics and Electrical Insulating Materi-
specification.
als
1.4 Poly(ether ether ketone), commonly referred to as
D792 Test Methods for Density and Specific Gravity (Rela-
PEEK, is a member of the poly (aryl ether ketone) or PAEK
tive Density) of Plastics by Displacement
family. Specification D6262 covers properties of PAEK shapes
D883 Terminology Relating to Plastics
and includes shapes produced from PEEK.
D1600 TerminologyforAbbreviatedTermsRelatingtoPlas-
NOTE1—ThisstandardandISO 23153addressthesamesubjectmatter,
tics
but differ in technical content.
D2863 Test Method for Measuring the Minimum Oxygen
1.5 The following precautionary caveat pertains only to the
Concentration to Support Candle-Like Combustion of
test method portion, Section 11, of this classification system:
Plastics (Oxygen Index)
This standard does not purport to address all of the safety
D3641 Practice for Injection Molding Test Specimens of
concerns, if any, associated with its use. It is the responsibility
Thermoplastic Molding and Extrusion Materials
of the user of this standard to establish appropriate safety,
D3418 Test Method for Transition Temperatures and En-
health, and environmental practices and determine the appli-
thalpies of Fusion and Crystallization of Polymers by
cability of regulatory limitations prior to use.
Differential Scanning Calorimetry
D3835 Test Method for Determination of Properties of
Polymeric Materials by Means of a Capillary Rheometer
1
This test method is under the jurisdiction ofASTM Committee D20 on Plastics
and is the direct responsibility of Subcommittee D20.15 on Thermoplastic Materi-
2
als. For referenced ASTM standards, visit the ASTM website, www.astm.org, or
Current edition approved Sept. 1, 2022. Published September 2022. Originally contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM
approved in 2016. Last previous edition approved in 2016 as D8033 - 16. DOI: Standards volume information, refer to the standard’s Document Summary page on
10.1520/D8033-22 the ASTM website.
*A Summary of Changes section appears at the end of this standard
Copyright © ASTM
...
This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
Designation: D8033 − 16 D8033 − 22
Standard Classification System for
Poly(Ether Ether Ketone) (PEEK) Molding and Extrusion
1
Materials
This standard is issued under the fixed designation D8033; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope Scope*
1.1 This classification system covers poly(ether ether ketone) materials suitable for injection molding and extrusion. This
classification system allows for the use of recycled materials provided that all specification requirements are met.
1.2 The properties included in this standard are those required to identify the compositions covered. Other requirements necessary
to identify particular characteristics important to specialized applications are to be specified by using the suffixes in Section 5.
1.3 This classification system and subsequent line callout (specification) are intended to provide means of calling out poly(ether
ether ketone) materials used in the fabrication of end items or parts. It is not intended for the selection of materials. It is
recommended that material selection be made by those having expertise in the plastics field only after careful consideration of the
design and the performance required of the part, the environment to which it will be exposed, the fabrication process to be
employed, the cost involved, and the inherent properties of the material other than those covered by this specification.
1.4 Poly(ether ether ketone), commonly referred to as PEEK, is a member of the poly (aryl ether ketone) or PAEK family.
Specification D6262 covers properties of PAEK shapes and includes shapes produced from PEEK.
NOTE 1—There is no known ISO equivalent to this standard.This standard and ISO 23153 address the same subject matter, but differ in technical content.
1.5 The following precautionary caveat pertains only to the test method portion, Section 11, of this classification system: This
standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user
of this standard to establish appropriate safety safety, health, and healthenvironmental practices and determine the applicability
of regulatory limitations prior to use.
1.6 This international standard was developed in accordance with internationally recognized principles on standardization
established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued
by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
2. Referenced Documents
2
2.1 ASTM Standards:
D149 Test Method for Dielectric Breakdown Voltage and Dielectric Strength of Solid Electrical Insulating Materials at
Commercial Power Frequencies
D256 Test Methods for Determining the Izod Pendulum Impact Resistance of Plastics
D257 Test Methods for DC Resistance or Conductance of Insulating Materials
1
This test method is under the jurisdiction of ASTM Committee D20 on Plastics and is the direct responsibility of Subcommittee D20.15 on Thermoplastic Materials.
Current edition approved Dec. 1, 2016Sept. 1, 2022. Published December 2016September 2022. Originally approved in 2016. Last previous edition approved in 2016 as
D8033 - 16. DOI: 10.1520/D8033-16.10.1520/D8033-22
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM Standards
volume information, refer to the standard’s Document Summary page on the ASTM website.
*A Summary of Changes section appears at the end of this standard
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1
---------------------- Page: 1 ----------------------
D8033 − 22
D570 Test Method for Water Absorption of Plastics
D618 Practice for Conditioning Plastics for Testing
D638 Test Method for Tensile Properties of Plastics
D648 Test Method for Deflection Temperature of Plastics Under Flexural Load in the Edgewise Position
D790 Test Methods for Flexural Properties of Unreinforced and Reinforced Plastics and Electrical Insulating Materials
D792 Test Methods for Density and Specific Gravity (Relative Density) of Plastics by Displacement
D883 Terminology Relating to Plastics
D1600 Terminology for Abbreviated Terms Relating to Plastics
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.